Tripp Lite DWT3285L User manual

1
Owner’s Manual
Tilt Flat Screen
Wall Mount
Model: DWT3285L
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2014 Tripp Lite. All rights reserved.
200 x 200 to
700 x 400
32”- 85”
MAX 56.6kg
(125lbs)
MAX
Este manual esta disponible en español en la página de Tripp Lite: www.tripplite.com
Ce manuel est disponible en français sur le site Web de Tripp Lite : www.tripplite.com
Русскоязычная версия настоящего руководства представлена на веб-сайте компании
Tripp Lite по адресу: www.tripplite.com
Dieses Handbuch ist in deutscher Sprache auf der Tripp Lite-Website verfügbar: www.tripplite.com
13-09-030-9332E8-EN.indd 1 4/3/2014 2:57:58 PM

2
NOTE: Read the entire instruction manual before you start installation and assembly.
Warranty & Warranty Registration
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this manual. If you have any questions regarding any
of the instructions or warnings, please visit www.tripplite.com/support.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone of good mechanical ability,
with basic building experience and a full understanding of this manual.
• Make sure that the supporting surface will safely support the combined load of
the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. The use of an edge-to-edge stud finder is highly
recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws rmly, but do not over tighten. Over tightening can damage the
items, greatly reducing their holding power.
• This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
5-Year Limited Warrant
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects
in material and workmanship for a period of 5 years from the date of initial purchase. If the product should
prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole
discretion.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE,
ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY
SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES,
INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY
PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL
DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions
may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from
jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate
or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes
no representation or warranty as to the suitability or fitness of these devices for any specific application.
WARRANTY REGISTRATION
Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You’ll be
automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
13-09-030-9332E8-EN.indd 2 4/3/2014 2:57:58 PM

3
Component Checklist
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to
installing. If any parts are missing or faulty, visit www.tripplite.com/support for service.
Wall Bracket (1) Mount Arms (2)
Mesh Sleeve (1) 4mm Security Hex Key (1)
M8x20 (4) M6x14 (4) M5x10 (2) Lag Bolts (4)
Concrete Anchor (4) Rubber Washer (4) Metal Washer (4) Cable Tie (2)
Note: Your hardware package includes security bolts that can only be fastened with the provided security hex key.
13-09-030-9332E8-EN.indd 3 4/3/2014 2:57:59 PM

4
1a. Mount on Wood Stud Wall
1
2
3
Find and mark the
exact location of
mounting holes
Screw the wall
plate onto the
wall
Drill pilot holes
WARNING
• Make sure that mounting screws are anchored into the center of the studs.
Use of an edge-to-edge stud finder is highly recommended.
• Never tighten in excess of 80 in-lb • (9 N.M.)
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined
load of the equipment and all attached hardware and components.
• When installing this wall mount on a wood stud wall covered with gypsum board
(drywall), verify that the wood studs are a minimum of 2” x 4” nominal size. When
installing to more than one stud, ensure the spacing between the studs is at least
16” but doesn’t exceed 24”. Do not install over gypsum board thicker than 5/8”.
65 mm
(2.5”)
ø 4 mm
(ø 5/32”)
Metal
Washer
Wall
Bracket
Lag Bolt
13-09-030-9332E8-EN.indd 4 4/3/2014 2:58:00 PM

5
1b. Mount on Solid Brick, Cinder Block or Concrete Wall
Concrete Anchor
Metal Washer
Lag bolt
Mark the
exact location of
mounting holes
Screw the wall
plate onto the
wall
Drill pilot holes
WARNING
• When installing wall mounts on a concrete wall, the wall must be at least 8” thick
with a minimum compressive strength of 2,000 psi.
• When installing wall mounts on cinder block, verify the actual concrete thickness is
at least 1-3/8” (35mm) for using the concrete anchors. When installing wall mounts
on a cinder block wall, the cinder blocks must meet ASTM C-90 specications and
have a minimum nominal width of 8”. Do not drill into mortar joints! Be sure to
mount in a solid part of the block, generally 1” (25mm) minimum from the side of
the block. It is suggested an electric drill on a slow setting be used to drill the hole
instead of a hammer drill to avoid breaking out the back of the hole when entering a
void or cavity.
• Installers must verify that the supporting surface will safely support the combined
load of the equipment and all attached hardware and components.
• Tighten screws so that wall bracket is rmly attached, but don’t overtighten.
Overtightening can damage screws, greatly reducing their holding power.
• Never Tighten in excess of 80 in-lb (9 N.M.)
• Always attach concrete anchors directly to load-bearing concrete.
• Never attach concrete anchors to concrete covered with plaster, drywall or other
finishing material.
1
2
64 mm
(2.5”)
ø 8 mm
(ø 5/16”)
13-09-030-9332E8-EN.indd 5 4/3/2014 2:58:01 PM

6
Note: Choose appropriate screws, washers and spacers (if necessary) according to the type of screen.
• Position the adapter brackets as close as possible to the center of the display.
• Screw the adapter brackets onto the display.
Tighten all screws but do not over tighten.
2. Attach Mount Arms to Display
TV
TV
TV
TV
TV
TV
or
Rubber
Washer
M8X20 M6X14
13-09-030-9332E8-EN.indd 6 4/3/2014 2:58:01 PM

7
3. Attach Mount Arms to Wall Bracket
Maintenance
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
• Please visit www.tripplite.com/support if you have any questions.
• Attach display to wall bracket and slide into position. Loosely fasten mount arms into place using security
screws.
• Adjust display until it’s in the desired position. Tighten security screws using supplied Hex key to lock into
place.
Wall Wall
Security Screw
13-09-030-9332E8-EN.indd 7 4/3/2014 2:58:02 PM

8
4. Height and Level Adjustment
Adjust display as desired.
• Turn knob CLOCKWISE to raise side.
• Turn knob COUNTER-CLOCKWISE to lower side.
UP
ROTATE LEFT ROTATE RIGHT
DOWN
13-09-030-9332E8-EN.indd 8 4/3/2014 2:58:03 PM

9
5. Tilt and Depth Adjustment
Adjust display as desired.
• Turn knob CLOCKWISE to move corner towards the wall.
• Turn knob COUNTER-CLOCKWISE to move corner away from the wall.
Note: Adjustments are made with the wall bracket open (see step 8 for instructions on opening the unit) and you facing the back of
your display.
IN OUT TILT FORWARD
TILT BACKWARD TILT RIGHT TILT LEFT
13-09-030-9332E8-EN.indd 9 4/3/2014 2:58:04 PM

10
6. Cable Management
7. Opening and Closing Wall Bracket
Display cables can be routed along top or bottom of wall bracket.
• Use mesh sleeve and cable ties for cable management.
To open wall bracket, push or pull up on locking tabs.
Important: Open position is for service access onl. The bracket must be closed during
normal use.
CABLES
Locking
Tab
Mesh
Sleeve
Cable
Tie
PULL UP
PUSH UP
Locking
Tab
13-09-030-9332E8-EN.indd 10 4/3/2014 2:58:06 PM

11
12
8. Opening and Closing Mount Arms
ORANGE CORD
ORANGE CORD
BLACK CORD
BLACK CORD
PULL
DOWN
PULL
DOWN
Open mount arms by pulling down on the orange cords while an assistant pulls the bottom of the display up and
away from the wall.
Important: Open position is for service access onl. The bracket must be closed during
normal use.
Pull display away from the wall slightly to release kickstand while an assistant pulls down on black cords. Once
black cords are pulled, kickstand will disengage.
Note: The kickstand will automatically engage. Make sure it is in the down position before letting go of the display.
Note: Support the display until the mount arms are engaged in the closed position.
To Close
To Open
13-09-030-9332E8-EN.indd 11 4/3/2014 2:58:07 PM

12
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
13-09-030 • 93-32E8_RevA
9. Securing Wall Bracket (Optional)
To prevent locking tabs from releasing, secure them with the two M5x10 Security Screws provided.
M5X10
13-09-030-9332E8-EN.indd 12 4/3/2014 2:58:07 PM