Tripp Lite SRCOOLNET2 User manual

Installation and
Quick Start Guide
SNMP/Web Management Accessory
Model: SRCOOLNET2
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2015 Tripp Lite. All rights reserved.
Read this manual carefully before installation. A separate User's Guide (PDF
format) is available for download at www.tripplite.com. Refer to the User's
Guide for additional information about configuration and operation.
Installation 2
Features 13
Tech Support 14
Warranty 14
Product Registration and 15
Regulatory Compliance
Español 16
Français 31
Русский 46
PROTECT YOUR INVESTMENT!
Register your product for quicker service and ultimate peace of mind.
You could also win an ISOBAR6ULTRA surge protector—a $50 value!
www.tripplite.com/warranty
15-02-247-93342E.indb 1 4/9/2015 9:52:07 AM

2
The SRCOOLNET2 allows the user to communicate with and control Tripp Lite’s
SRCOOL7KRM and SRCOOL18K spot coolers as manageable devices on a network
accessible via Web Browser, Network Management Station or Telnet.
1 - Preparation
1-1 Confirm Package Contents: In addition to this manual, your package should
include the following:
• Configuration cable (73-1025)
• ENVIROSENSE Module
• ENVIROSENSE User Manual
1-2 Locate MAC Address: The 12-digit MAC address (000667xxxxxx) is located on
the SRCOOLNET2.
Installation
2 – Installation
2-1 Insert the SRCOOLNET2 into the front SNMP accessory slot on the
SRCOOL7KRM or SRCOOL18K (Figure 1 in section 4-2).
2-2 Connect SRCOOLNET2 to Network: Connect a standard Ethernet patch cable
to the RJ45 Ethernet port on the SRCOOLNET2. Note: This port does not
support PoE (Power over Ethernet) applications.
2-3 Determine Network Installation Method: If your network's DHCP server will
assign a dynamic IP address to the SRCOOLNET2 automatically, proceed to
3 - Dynamic IP Address Assignment. If you will assign a static IP address to
the SRCOOLNET2 manually, proceed to 4 - Static IP Address Assignment. If
you are uncertain which method to use, contact your network administrator for
assistance before continuing the installation process.
15-02-247-93342E.indb 2 4/9/2015 9:52:07 AM

3
Installation
3 - Dynamic IP Address Assignment
3-1 Connect SRCOOLNET2 to Network: By default, the SRCOOLNET2 will attempt
to obtain an IP address via DHCP. This may take as long as several minutes,
depending on your network environment.
3-2 Discover IP Address: Contact your network administrator to determine which IP
address has been assigned to the SRCOOLNET2 by the DHCP server. The card
can be identified on the DHCP server by referring to its MAC address (see Step
1-2). You may wish to request a long-term lease period for the IP address,
depending on your application. After you have discovered the IP address,
proceed to 5 - Test and Configure.
Note: If you prefer, you can determine the DHCP address during boot-up.
Connect a computer running a terminal emulation program to the SRCOOLNET2
using the configuration cable and reset the SRCOOLNET2.
15-02-247-93342E.indb 3 4/9/2015 9:52:07 AM

4
Installation
4 - Static IP Address Assignment/Terminal Menu
Configuration Settings
4-1 Determine IP Information: Before assigning a static IP address, you'll need to
know the IP address, gateway address and subnet mask. If you do not have this
information, contact your network administrator for assistance.
4-2 Connect SRCOOLNET2 to Computer: Use the included mini-DIN to DB9
configuration cable (part number 73-1025) to connect the SRCOOLNET2 to the
computer. The circular connector Aat one end of the cable attaches to the
8-pin mini-DIN serial port (labeled CONFIG) Bon the SRCOOLNET2 (align the
connector carefully to avoid damaging the pins). The DB9 connector Cat the
other end of the cable connects to the computer’s serial port D.
SRCOOL7KRM SRCOOL18K
OR
Figure 1
AA
D
BB
C
15-02-247-93342E.indb 4 4/9/2015 9:52:08 AM

5
Installation
4-3 Configure Terminal Emulation Program: Open a VT100-compatible terminal
emulation program (such as Tera Term) on a computer with an available DB9
serial port. The example below illustrates the use of a Tripp Lite USB-to-Serial
converter.
4-3.1
Set the terminal emulation program to use the COM port that corresponds to the
DB9 serial port.
15-02-247-93342E.indb 5 4/9/2015 9:52:08 AM

6
Installation
4-3.2
Specify the parameters required to communicate with the SRCOOLNET2 terminal
interface. Click Setup, then select Serial Port.
15-02-247-93342E.indb 6 4/9/2015 9:52:08 AM

7
Installation
Press A to Accept the settings,
or M to Modify? m
Enter the root password: *********
Reset configuration and root password to default values? n
For each of the following questions, you can press <Return> to select the value
shown in braces, or you can enter a new value.
ETHERNET INTERFACE SETTINGS:
Obtain IPv4 settings automatically using DHCP for Ethernet interface [Y]? n
IP address [10.1.0.165]? 192.168.1.2
IP address IP address is 192.168.1.2
Subnet mask [255.255.255.0]?
Gateway address [10.0.0.1]? 192.168.1.1
Gateway address IP address is 192.168.1.1
Enable DHCPv6 for the Ethernet interface [N]?
Enable static IPv6 for the Ethernet interface [N]? y
4-4 Configure SRCOOLNET2 in Terminal Mode: Note: The SRCOOLNET2 must be
reinitialized by pressing the reset button (located between the "Link" and "Status"
descriptions under the RJ45 port on the SRCOOLNET2), for 3 seconds. After the
reset, an initialization page should appear in the terminal emulation program.
When the message below appears, press any key on the keyboard within 5
seconds. If the 5-second period has elapsed, you can reinitialize the
SRCOOLNET2.
Press any key in 5 seconds to change these settings.
Follow the sequence of responses below in order to assign a static IP address to
the SRCOOLNET2.
The default root password is TrippLite. Sample IP settings are shown – supply
your own IPv4 or IPv6 information when you configure your SRCOOLNET2.
When the message below appears, enter ‘m’ to modify the SRCOOLNET2's
settings.
15-02-247-93342E.indb 7 4/9/2015 9:52:08 AM

8
IPv6 address [2001:DB8::1:58:4F43:4849:544C]? fd36:a66d:8c61:8e65:19af:94e9:d8
8c:1
Network prefix length [64]?
IPv6 gateway [::]? fd36:a66d:8c61:8e65::1
DNS server [8.8.8.8]?
This card's host name [poweralert-0641576753151]?
This card's domain []?
For each of the remaining questions, you can press <Return> to select the
value shown in braces, or you can enter a new value. Tripp Lite recommends
against changing the default settings unless you are an advanced user with a
specific purpose.
After you have finished entering settings, the SRCOOLNET2 will save changes to
NV memory and reboot (this may take several minutes).
Saving the changes in NV memory...Done.
After the SRCOOLNET2 reboots, the initialization page should display the new
static IP settings.
PLATFORM: trippliteSnmpCard9210_H_16_32 16M/32M
------------------------------------------------------------------------------
NETWORK INTERFACE PARAMETERS:
FQDN poweralert-0641576753151
IP address on LAN is 192.168.1.2
LAN interface's subnet mask is 255.255.255.0
IP address of default gateway to other networks is 192.168.1.1
IPv6 static address on LAN is FD36:A66D:8C61:8E65:19AF:94E9:D88C:1 prefixlen 64
IPv6 gateway on LAN is FD36:A66D:8C61:8E65::1
DNS server is 8.8.8.8
Time is supplied by SNTP at an interval of 360 minutes
Primary SNTP Server host is 0.pool.ntp.org
Secondary SNTP Server host is 1.pool.ntp.org
Time zone is set to -6:00 from GMT, DST Enabled
Installation
15-02-247-93342E.indb 8 4/9/2015 9:52:08 AM

9
Installation
5 - Test and Configure
5-1 Test Network Connection: After an IP address has been assigned to the
SRCOOLNET2, try to access it with a Web browser that supports Java™. Open a
Web browser on a computer connected to the LAN and enter the SRCOOLNET2’s
IP address. The user name is localadmin and the default password is localadmin.
After you enter the user name and password, the PowerAlert Status page will
appear in the browser window. For more information about configuration and
operation of the managed device, refer to the Owner’s Manual, available for
download at www.tripplite.com.
Note: When using the SRCOOLNET2 with the SRCOOL7KRM or SRCOOL18K, do
not use the cooling unit’s manual control panel.
4-5 Remove Configuration Cable: Remove the configuration cable that connects
the SRCOOLNET2 to the computer.
15-02-247-93342E.indb 9 4/9/2015 9:52:08 AM

10
Installation
6 - Using ENVIROSENSE®and Remote Temperature
Setpoint Control
SRCOOLNET2 supports the use of the ENVIROSENSE environmental sensor (included)
to control the unit instead of the default temperature sensor in the AC unit’s return
airstream. The ENVIROSENSE sensor can be located in the area you wish to control to
the specific setpoint.
6-1 Configuring SRCOOLNET2 for Remote Setpoint Usage
To use the Remote Temperature Setpoint mode of operation, ensure that the
ENVIROSENSE device is installed and connected to the SRCOOLNET2 A.
ENVIROSENSE
MODULE
SRCOOLNET2
ENVIROSENSE
MODULE
SRCOOLNET2
A
15-02-247-93342E.indb 10 4/9/2015 9:52:09 AM

11
Installation
The SRCOOL7KRM or SRCOOL18K will now begin cooling when the temperature
reading at ENVIROSENSE equals or exceeds the setpoint value you entered.
When the temperature falls below this setpoint, the unit will stop cooling. If the
'Always On' checkbox is checked, the fans will remain running when the unit
stops cooling. If the 'Always On' checkbox is unchecked, the fans will shut off
and the SRCOOL7KRM or SRCOOL18K display will extinguish. Once the
temperature reaches the setpoint again, the unit will restart and begin cooling
until the temperature reported by ENVIROSENSE returns below the setpoint. This
cycle will continue indefinitely until you select STOP from the SRCOOLNET2 user
interface or turning the SRCOOL unit off via the device display panel.
Turn the unit on. From the SRCOOLNET2 user interface, make sure that the
ENVIROSENSE has been discovered/discover it. Click the 'Remote' checkbox to
override the setpoint control on the device display panel B. Type in the remote
setpoint you wish to target and press ENTER. The setpoint control on the device
display panel will be overridden.
B
15-02-247-93342E.indb 11 4/9/2015 9:52:09 AM

12
Installation
6-2 Important Considerations When Using Remote Temperature Setpoint Mode
It is important to keep the following considerations in mind when using the
Remote Temperature Setpoint feature of SRCOOLNET2:
1The temperature being used for controlling the attached cooling device is the
ENVIROSENSE sensor, NOT the return air temperature. The return air
temperature may be higher or lower than the temperature ENVIROSENSE is
reporting.
2The setpoint displayed on the attached cooling device display panel should
be ignored when the SRCOOLNET2 is set to Remote Temperature Setpoint
mode in PowerAlert. The setpoint displayed on the device display panel will
be the minimum (when cooling) or maximum (when not cooling) setpoint
permissible by the cooling unit.
3If the SRCOOLNET2 fan control is set to “always on” and the temperature at
the return air intake of the cooling device is outside the limits of the cooling
device, the ENVIROSENSE reading and remote setpoint will be overridden.
The return air temperature sensor will control the AC unit until the return air
temperature returns to the normal operating range. For this reason it is
important to ensure that the cooling unit air intake temperature be between
65°F (18°C) and 90°F (32°C ) for the Remote Temperature Setpoint to work
correctly.
4If the power button on the cooling unit display panel is pressed while in
Remote Temperature Setpoint mode, the mode will be canceled.
15-02-247-93342E.indb 12 4/9/2015 9:52:09 AM

13
Features
PS/2 Port: Use this port to connect the Tripp Lite ENVIROSENSE
environmental sensor to provide remote temperature/humidity
monitoring and a dry contact interface to control and monitor
alarm, security and telecom devices. Note: Do not connect a
keyboard or mouse to this port.
Mini-DIN Serial Port: Use this port to provide a direct terminal
connection to a computer with a terminal emulation program.
A configuration cable (part number 73-1025) is included with the
SRCOOLNET2. If you need to order a replacement cable, visit
www.tripplite.com/support.
RJ45 Ethernet Network Port: Use this RJ45 jack to connect the
SRCOOLNET2 to the network with a standard Ethernet patch cable.
The Link LED C1 and Status LED C2 indicate several operating
conditions, as shown in the table below. Does not support PoE
(Power Over Ethernet) applications.
SRCOOLNET2 Operating Conditions
C1 Link LED Color
Off No Network Connection
Flashing Amber 100 Mbps Network Connection
Flashing Green 10 Mbps Network Connection
C2 Status LED Color
Off SRCOOLNET2 Not Initialized
Steady Green SRCOOLNET2 Initialized and Operational
Flashing Amber Error - SRCOOLNET2 Not Initialized
SNMP Reset Button: Press the reset button for 3 seconds to
reboot the SRCOOLNET2. Rebooting the SRCOOLNET2 will not
erase network settings or power. Note: The recessed button is
located beneath the Ethernet port. Use a pin, paper clip, or pointed
tool to access the button. Do not use excessive force when
engaging the button.
C1 C2
RESET
15-02-247-93342E.indb 13 4/9/2015 9:52:09 AM

14
Technical Support can be found at: www.tripplite.com/support
Warranty
Technical Support
LIMITED WARRANTY
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects
in material and workmanship for a period of 2 years (except internal UPS system batteries outside USA and
Canada, 1 year) from the date of initial purchase. If the product should prove defective in material or
workmanship within that period, Seller will repair or replace the product, in its sole discretion. Service under this
Warranty can only be obtained by your delivering or shipping the product (with all shipping or delivery charges
prepaid) to: Tripp Lite, 1111 W. 35th Street, Chicago, IL 60609, USA. Seller will pay return shipping charges. Visit
www.tripplite.com/support before sending any equipment back for repair.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE,
ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET
FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING
ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET
FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES.
(Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not
apply to you. This Warranty gives you specific legal rights, and you may have other rights which vary from
jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate
or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes
no representation or warranty as to the suitability or fitness of these devices for any specific application.
Not compatible with PoE (Power over Ethernet) applications.
15-02-247-93342E.indb 14 4/9/2015 9:52:09 AM

15
Product Registration and Regulatory Compliance
PRODUCT REGISTRATION
Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You'll be automatically entered into a
drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
CAUTION: Use of this equipment in life support applications where failure of this equipment can reasonably be
expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not
recommended. Do not use this equipment in the presence of a flammable anesthetic mixture with air, oxygen or
nitrous oxide.
WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)
Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations,
when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to:
• Send old equipment for recycling on a one-for-one, like-for-like basis
(this varies depending on the country)
• Send the new equipment back for recycling when this ultimately becomes waste
Regulatory Compliance Identification Numbers
For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned
a unique series number. The series number can be found on the product nameplate label, along with all required
approval markings and information. When requesting compliance information for this product, always refer to the
series number. The series number should not be confused with the marketing name or model number of the
product.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
15-02-247-93342E.indb 15 4/9/2015 9:52:09 AM

16
Guía de Instalación
e Inicio Rápido
Accesorio para administración
SNMP/Web
Modelo: SRCOOLNET2
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2015 Tripp Lite. Todos los derechos reservados.
Antes de la instalación, lea cuidadosamente este manual. Está disponible
una Guía del Usuario (Formato PDF) independiente para descarga en www.
tripplite.com. Para información adicional acerca de la configuración y
operación, consulte la Guía de Usuario.
Instalación 17
Características 28
Soporte Técnico 29
Garantía 29
Cumplimiento de las Normas 30
English 1
Français 31
Русский 46
MÁS DE
15-02-247-93342E.indb 16 4/9/2015 9:52:10 AM

17
El SRCOOLNET2 permite al usuario comunicarse con los enfriadores de puntos
SRCOOL7KRM y SRCOOL18K de Tripp Lite y controlarlos como dispositivos
administrables sobre su red y son accesibles mediante explorador de Internet,
Estación de Administración de Red o Telnet.
1 - Preparación
1-1 Confirme el Contenido del Paquete: Además de este manual, su paquete
debe incluir lo siguiente:
• Cable de configuración (73-1025)
• Módulo ENVIROSENSE
• Manual de Usuario de ENVIROSENSE
1-2 Localice la Dirección MAC: La dirección MAC de 12 dígitos (000667xxxxxx) se
localiza en el SRCOOLNET2.
Instalación
2 – Instalación
2-1 Inserte el SRCOOLNET2 en la ranura frontal auxiliar SNMP en el
SRCOOL7KRM o SRCOOL18K (Figura 1, sección 4-2).
2-2 Conecte el SRCOOLNET2 a la Red: Conecte un cable patch estándar de
Ethernet al puerto Ethernet RJ45 en el SRCOOLNET2. Nota: Este puerto no
soporta aplicaciones PoE (Energía sobre la Ethernet).
2-3 Determine el método de instalación en Red: Si el servidor DHCP de su red
asignará automáticamente una dirección IP dinámica al SRCOOLNET2, proceda
a 3 - Asignación de Dirección IP Dinámica. Si usted asignará manualmente
una dirección IP estática a la SRCOOLNET2 proceda a 4 - Asignación de
Dirección IP Estática. Si no está seguro de cuál método usar, póngase en
contacto con su administrador de red para asistencia antes de continuar el
proceso de instalación.
15-02-247-93342E.indb 17 4/9/2015 9:52:10 AM

18
Instalación
3 - Asignación de Dirección IP Dinámica
3-1 Conecte SRCOOLNET2 a la Red: De fábrica, el SRCOOLNET2 intentará obtener
una dirección IP mediante DHCP. Esto puede tomar unos minutos, dependiendo
de su entorno de red.
3-2 Averigüe la dirección IP: Póngase en contacto con su administrador de red
para determinar qué dirección IP asignó el servidor DHCP al SRCOOLNET2. La
tarjeta puede identificarse en el servidor DHCP refiriéndose a su dirección MAC
(ver Paso 1-2). Puede desear solicitar un período de concesión a largo plazo
para la dirección IP, dependiendo de su aplicación. Después de que averigüe la
dirección IP, proceda a 5 - Pruebe y Configure.
Nota: Si lo prefiere, puede determinar la dirección DHCP durante el arranque.
Conecte una computadora corriendo un programa de emulación de terminal al
SRCOOLNET2 usando el cable de configuración y restaure el SRCOOLNET2.
15-02-247-93342E.indb 18 4/9/2015 9:52:10 AM

19
Instalación
4 - Parámetros de configuración de Menú de Asignación/
Terminal de Dirección IP Estática
4-1 Determine la información de IP: Antes de asignar una dirección IP estática,
deberá conocer la dirección IP, dirección de portal y máscara de subred. Si no
tiene esa información, comuníquese con el administrador de su red para obtener
asistencia.
4-2 Conecte el SRCOOLNET2 a la Computadora: Use el cable de configuración de
mini DIN a DB9 (número de parte 73-1025) incluido para conectar el
SRCOOLNET2 a la computadora. El conector circular Aen un extremo del cable
se acopla al puerto serial mini DIN de 8 pines (etiquetado CONFIG) Ben el
SRCOOLNET2 (alinee cuidadosamente el conector para evitar dañar los pines).
El conector DB9 Cen el otro extremo del cable se conecta al puerto serial de la
computadora D.
SRCOOL7KRM
COMPUTADORA
CON PUERTO DB9
SRCOOL18K
O
Figura 1
AA
D
BB
C
15-02-247-93342E.indb 19 4/9/2015 9:52:11 AM

20
Instalación
4-3 Configure el Programa de Emulación de Terminal: Abra un programa de
emulación compatible con VT100 (como el Tera Term) en una computadora con
un puerto serial DB9 disponible. El siguiente ejemplo ilustra el uso de un
convertidor USB a Serial de Tripp Lite.
4-3.1
Configure el programa de emulación de terminal para usar el puerto COM que
corresponde al puerto serial DB9.
15-02-247-93342E.indb 20 4/9/2015 9:52:11 AM