Tripp Lite 0DT60001 User manual

ssasdfasdfasdf
KVM Extender USB
Quick Start Guide
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Copyright ©2012 Tripp Lite. All rights reserved.

KVM EXTENDER USB
1
1. Introduction
The KVM Extender USB system from Minicom is an advanced KVM extender that
performs the following functions:
Extends KVM control over a computer up to a distance of 150m / 500ft
Gives 2 users at 2 workstations control of 1 computer
A 2-port KVM switch at the remote workstation
Full USB keyboard and mouse control
2. System components
The KVM Extender USB system consists of:
Transmitter
Receiver
2 x VGA+USB cable
1 Power adapter for the Receiver
1 Screwdriver
8 non-stick rubber stops
3. The KVM Extender USB units
The figures below illustrate the Transmitter unit.
Figure 1 Transmitter front panel
3.1 Transmitter Button / LEDs
Button / LED Function
Lock button Press to keep control of the connected
computer at the Transmitter position
Control LED Blinks when Transmitter position has control
of the Transmitter position computer
Lock LED Blinks after either Transmitter or Receiver
position presses the Lock button for control
LOCK
MINICOMKVM EXTENDER USB
LOCKCONTROL
Keyboard
USB connector
Mouse USB
connector Lock button
Local + Lock
LEDs

QUICK START GUIDE
2
Figure 2 Transmitter back panel
The figures below illustrate the Receiver unit. The Receiver can be up to 150m / 500ft
away from the Transmitter.
Figure 3 Receiver front panel
3.2 Receiver Buttons / LEDs
Button / LED Function
Lock button Press to lock control of the Transmitter
computer at the Receiver position
Local button Press to toggle control between the local
Receiver computer and the remote
Transmitter computer (see also section 8.1 on
page 6)
Lock LED Blinks after either Transmitter or Receiver
position presses the Lock button
Local LED Blinks when Receiver position has control of
the Receiver position computer
Figure 4 Receiver back panel
CONTROLPOWER SYSTEM COMPUTER
Power connector Local monitor Computer cable
(Optional)
Control box
System cable
Keyboard
USB connector
Mouse USB
connector
LOCK
MINICOMKVM EXTENDER USB
LOCKLOCAL LOCAL
Lock button
Local button
Local + Lock
LEDs
Power connector
CONTROLPOWER SYSTEM COMPUTEREq
Luminance +
Equalization
selector
Lu
(Optional)
Control box
System cable
Local monitor Computer cable

KVM EXTENDER USB
3
4. Pre-installation instructions
Place cables away from fluorescent lights, air conditioners, and machines that are
likely to generate electrical noise.
5. Connecting the System
When using the system as an extender, extending KVM control from the computer up
to a distance of 150m/500ft, connect the system as in Figure 5. The connections are
explained below.
Figure 5 KVM Extender USB as an extender
5.1 Connecting the Transmitter
Connect a VGA + USB cable - illustrated below - to the Transmitter and a computer.
Connect the HD15 connector to the Transmitter Computer port and connect the VGA
and USB connectors to the local computer Monitor and USB ports.
Figure 6 VGA + USB cable
5.2 Connecting a KVM workstation to the Receiver
Connect a KVM workstation to the Receiver. Connect a keyboard and mouse to the
Receiver Keyboard and Mouse USB ports. Connect a monitor to the Receiver Monitor
port.
Receiver Transmitter
Extended User
position CAT5 cable - 150m/500ft
VGA + USB cable

QUICK START GUIDE
4
5.3 Connecting the System cable
Connect the System cable CAT5/6/7 FTP cable to the System ports of the Transmitter
and Receiver.
5.4 Connecting to the power supply
The Transmitter receives its power from the connected computer and does not
generally need an external power supply. However, when the Transmitter is connected
to a KVM switch it may need an external power supply. Use a Minicom Power
adapter 12VDC 1A, ordered separately p/n 5PSA70020.
Connect the Receiver to the power supply with the Power adapter and cord provided.
6. Extender system with optional computer at
Receiver position
You can connect a computer to the Receiver position. The Receiver position can then
either control the local computer or the Transmitter position computer.
Figure 7 Extender system with optional computer at Receiver position
The connections are the same as outlined above, with the addition of a
computer connected to the Receiver as follows:
6.1 Connecting a computer to the Receiver
Connect a VGA + USB cable to the Receiver and a computer. Connect the HD15
connector to the Receiver Computer port and connect the VGA and USB connectors
to the computer Monitor and USB ports.
Receiver Transmitter
Local User
position
Extended User
position CAT5 cable - 150m/500ft
Optional PC

KVM EXTENDER USB
5
7. Extender + KVM switch system with optional
computer at Receiver position
You can connect a KVM switch to the Receiver position. The Receiver position can
then either control the local computer or any computer connected to the KVM switch
at the Transmitter position computer.
Figure 8 Extender + KVM switch with optional computer at Receiver position
The connections are the same as outlined above, with the addition of a KVM
switch connected to the Transmitter as follows:
Connect a VGA + USB cable to the Transmitter and the KVM switch. Connect
the HD15 connector to the Transmitter Computer port and connect the VGA
and USB connectors to the KVM switch Monitor and USB ports.
8. Operating the KVM Extender USB system
The system works on a first come first served basis – press the keyboard or move the
mouse at either the Transmitter (where relevant) or Receiver position to take control
of the Transmitter position computer.
Transmitter position: Press the Lock button to keep/gain control of the computer at
the Transmitter position. The Lock LED at the Transmitter position illuminates and
blinks at the Receiver position. The Control LED at the Transmitter position
illuminates.
Receiver position: Press the Lock button to keep control of the Transmitter computer
at the Receiver position. The Lock LED at the Receiver position illuminates and
blinks at the Transmitter position.
Press the Local button to gain control of the Receiver computer position. The Local
LED blinks.
I
012345678 1
01 11 21 31 41 51 6
9
Receiver Transmitter
Local User
position
KVM Switch
Extended User
position CAT5 cable - 150m/500ft
Optional PC

QUICK START GUIDE
6
Note! You can only gain control by pressing the Lock button if the Lock LED is
currently not blinking.
Re-pressing the Lock button at either position releases control and the Lock LEDs
turn off.
8.1 Keyboard hotkeys
To toggle between the Transmitter and the Receiver position, press: Caps Lock twice,
release, then press C.
To turn the beeper sound on/off, press: Caps Lock twice, release, then press B.
8.2 Adjusting the picture
At the Receiver, you can adjust the picture quality using a small screwdriver to turn
the Luminance and Equalization Picture adjusters located on the Receiver’s rear
panel.
9. Safety
The device must only be opened by an authorized Minicom technician. Disconnect
device from AC mains before service operation!
9.1 User guide feedback
Your feedback is very important to help us improve our documentation. Please email
any comments to: [e-mail]
Please include the following information: Guide name, part number and version
number (as appears on the front cover).
9.2 WEEE compliance
WEEE Information for Minicom Customers and Recyclers
Under the Waste Electrical and Electronic Equipment (WEEE) Directive and
implementing regulations, when customers buy new electrical and electronic
equipment from Minicom they are entitled to:
Send old equipment for recycling on a one-for-one, like-for-like basis (this
varies depending on the country)
Send the new equipment back for recycling when this ultimately becomes
waste
Instructions to both customers and recyclers/treatment facilities wishing to obtain
disassembly information are provided in our website www.minicom.com.

KVM EXTENDER USB
7
10. Technical specifications
System cable CAT5/6/7 FTP 2x4x24 AWG Solid Wire cable
Maximum distance 150m/500ft
Mouse support USB mouse
Operating systems All major operating systems
Management Push button or external control unit
Screen resolution Up to 1600X1200 @ 75Hz
Operating temperature 0°C to 40°C/32°F to 104°F
Storage temperature -40°C to 40°C/-40°F to 104°F
Warranty 3 Years limited
Transmitter Receiver
Cables & connectors
HDD15F (VGA + USB
cable) – for computer or
KVM switch
HDD15F (VGA + USB cable)
- for optional local computer
USB X 2: for Keyboard +
Mouse USB X 2: for Keyboard + Mouse
HDD15 : for monitor HDD15 : for monitor
RJ45 - System RJ45 - System
RJ11 - External control unit RJ11 - External control unit
Dimensions 85 x 113 x 25mm/
3.3 x 4.4 x 0.98 inches
85 x 49 x 25mm/
3.3 x 4.4 x 0.98 inches
Shipping weight 1,750g/3.9lb
Power supply From computer or
external power
adapter 12VDC 1A
External power adapter 12VDC 1A
201204190 • 933192_EN