Tripp Lite SmartPro 2200XLT User manual

1
Copyright © 1999 Tripp Lite. All rights reserved. SmartPro®is a registered trademark of Tripp Lite.
Installation: p. 3 - 4
Basic Operation: p. 4 - 6
Storage & Service: p. 7
Specifications: p. 7
Safety: p. 2
Warranty & Insurance: p. 6
1111 W. 35th Street
Chicago, IL 60609 USA
Customer Support: [phone]
www.tripplite.com
Owner's Manual
SmartPro®
2200XLT
Line-Interactive
UPS Systems (230V)
9911081 230V Smartpro 2200T OM.p65 11/24/99, 12:00 PM1

2
This manual contains important instructions and warnings that should be
followed during the installation, operation and storage of all Tripp Lite UPS
Systems.
UPS Location Warnings
• Install your UPS indoors, away from excess moisture or heat, dust or
direct sunlight.
• For best performance, keep the indoor temperature between 32° F and
104° F (between 0° C and 40° C).
• Leave adequate space around all sides of the UPS for proper ventilation.
UPS Connection Warnings
• Connect your UPS to a properly grounded AC power outlet. Do not
remove or modify the UPS's plug.
• Do not use two-prong adapters with the UPS's plug. Do not plug your
UPS into itself; this will damage the UPS and void your warranty.
• If you are connecting your UPS to a motor-powered AC generator,
the generator must provide clean, filtered computer-grade output.
Equipment Connection Warnings
• Do not use Tripp Lite UPS Systems for life support applications in which
a malfunction or failure of a Tripp Lite UPS System could cause failure
or significantly alter the performance of a life-support device.
• Do not connect surge suppressors to the output of your UPS. This may
damage your UPS and will void both the surge suppressor and UPS
warranties.
Battery Warnings
• Your UPS does not require routine maintenance. Do not open your UPS
for any reason. There are no user-serviceable parts inside.
• Battery replacement must be performed by qualified service personnel.
Because the batteries present a risk of electrical shock and burn from
high short-circuit current, observe proper precautions. Unplug and turn
off the UPS before performing battery replacement. Use tools with
insulated handles and replace the existing batteries with the same
number and type of new batteries (Sealed Lead-Acid). Do not open the
batteries. Do not short or bridge the battery terminals with any object.
• The UPS batteries are recyclable. Refer to local codes for disposal
requirements or call 1-800-SAV-LEAD (1-800-728-5323) for complete
recycling information. Do not dispose of the batteries in a fire.
• Connect only Tripp Lite battery packs with the correct voltage (see voltage
requirements label on the rear of your UPS) and the correct connector color
to match your UPS’s External Battery Connector.
• Do not plug UPS in or operate without batteries.
Safety
9911081 230V Smartpro 2200T OM.p65 11/24/99, 12:00 PM2

3
Installation
Plug your UPS into
an electrical outlet.
The SmartPro 2200XLT should be connected to a
15-amp dedicated circuit.
Plug your equipment
into your UPS.
Turn your UPS ON.
Set the System Enable Switch (DIP
Switch #4, UPS back panel) to the
“ENABLE” (UP) position.
(See Figure 1)
This switch activates the battery charger and
microprocessor.
The “ ” light will flash until you engage the
ON/Standby Switch to activate the “ON” mode.
Engage the momentary ON/Standby
Switch (UPS front panel) and release it
to activate the “ON” mode and supply
power to the UPS receptacles.
(See Figure 2)
3
2
1
DB9 Port Connection (Optional) On Next Page . . .
Figure 2 - ON/Standby Switch
Figure 1 DIP Switch #4
(System Enable Switch)
ENABLE
DISABLE
Your UPS is designed to support
only computer equipment.
Connecting household appliances,
laser printers or surge suppressors
is not recommended.
·
·
9911081 230V Smartpro 2200T OM.p65 11/24/99, 12:00 PM3

4
Switches
System Enable Switch (DIP Switch #4)
This switch is located in the set of 4 switches next to the UPS’s DB9
ports. It activates the battery charger and intelligent microproces-
sor. Always leave it in the “ENABLE” (UP) position when your UPS
is plugged in. Set the switch to “DISABLE” (DOWN) only if you store
or ship your UPS (to reduce battery drain).
Note: the “XXX” light will flash until you engage the ON/Standby Switch to activate the “ON”
mode (power ON at the UPS receptacles).
3
2
1
DB9 Port Connection
–Optional–*
Using Tripp Lite cable, connect your
primary server’s DB9 port to the
single DB9 port labeled SMART/LAN
4.1 (which provides complete
intelligent RS-232 communications)
using the included cable labelled
73-743.**
If you have additional
computers:
Connect them to the DB9 ports
labeled BASIC/LAN 2.2 (which provide
basic, contact-closure shutdown
capabilities) using the included
cables labelled 73-844.
Set their corresponding LAN Interface
DIP Switches to the ACTIVATE
(DOWN) position. See diagram for
which switch controls which port.***
* Serial port connections are optional. Your UPS will function properly without these connections.
** The SMART/LAN 4.1 port is always enabled and is not controlled by the LAN Interface DIP Switches.
*** If you do not connect a computer to either of the BASIC/LAN 2.2 ports, set their corresponding LAN Interface DIP
Switches to the DEACTIVATE (UP) position. Note: DIP Switch #3 has no function.
a.
b.
2a. Back Panel
Basic Operation
Load software and run the installation program
appropriate for your operating system.
2b. Back Panel
DIP Switches #2 & #1
(Lan Interface Switches)
DEACTIVATE
ACTIVATE
9911081 230V Smartpro 2200T OM.p65 11/24/99, 12:00 PM4

5
ON/Standby Switch
This momentary switch controls power to the UPS receptacles.
Engage it momentarily and release it to toggle between the “ON”
mode (power ON at the UPS receptacles) and “Standby” mode
(power OFF at the UPS receptacles).
Mute/Test Switch
Use this momentary switch to do two things:
Silence the blackout alarm
Engage this switch and release it. Note: when the battery is nearly
depleted, the alarm resumes (and cannot be silenced) to alert you
to immediately shut down connected equipment.
Test your UPS’s battery charge
Leave your connected equipment ON. With your UPS plugged in
and completely turned ON, engage this switch; hold it there for 5
seconds and release it. The UPS will momentarily switch to battery
to test its charge. The “XXX” light will turn ON and the alarm may
sound if your UPS fails a self-test and/or the UPS battery is less
than fully charged. Let the UPS charge for 12 hours and perform
a second self-test. If the light continues to stay on, contact Tripp
Lite for service. CAUTION: Do not unplug your UPS to test its
batteries. This will remove safe electrical grounding and may
introduce a damaging surge into your network connections.
Indicator Lights
All Indicator Light descriptions apply when the UPS is plugged into a wall outlet
and turned ON.
This green light will shine constantly to indicate AC power is
available at the receptacles. It will flash to indicate AC power is not
available. (See “System Enable Switch” and “ON/Standby Switch”
descriptions above.)
This multi-colored light displays 7 separate UPS battery charge
conditions. It will turn from red (low) to yellow (medium) to green
(full) to show you the level of battery charge. If the light is constant,
then your UPS is operating from line power and the battery is
charging. If the light is flashing, then your UPS is operating from
battery power and the battery is discharging. When the light
flashes red, close any files you are working on and shut down your
computer.
Whenever your UPS is automatically correcting high or low AC line
voltage, this green light will turn ON and the UPS will gently click.
The more the UPS has to correct voltage, the more the green light
will turn ON and the more the UPS will click. These are both
normal, automatic operations of your UPS, and no action is
required on your part.
This red light will turn ON if your UPS fails a self-test and/or the
UPS battery is less than fully charged. Let the UPS charge for 12
hours and perform a second self-test. If the light continues to stay
on, contact Tripp Lite for service.
9911081 230V Smartpro 2200T OM.p65 11/24/99, 12:00 PM5

6
This multi-colored light displays 4 separate UPS load conditions.
It will turn from green (low) to yellow (medium) to red (high) as you
connect equipment to show you the load level your UPS is support-
ing. When the light is red your UPS is supporting a load above 85%
of its capacity. If the red light begins flashing, your UPS is severely
overloaded. Remove overload immediately until light stops flashing.
Other UPS Features
L6-20 AC Receptacle
This locking receptacle provides your connected equipment with
AC line power during normal operation and battery power during
blackouts and brownouts. It also protects your equipment against
damaging surges and line noise. You can remotely reboot con-
nected equipment by turningthe UPS OFF and ON using Tripp Lite
UPS software. See software instructions for details.
SMART/LAN 4.1 (RS-232) Port
The RS-232 port connects your UPS to any workstation or server.
Use with Tripp Lite software and cabling to monitor and manage
network power and automatically save open files and shut down
equipment during a blackout. This port uses RS-232 communica-
tions to transmit UPS and power conditions. Select models feature
plug-and-play capability. Contact Tripp Lite Customer Support for
more information and a list of available SNMP, network manage-
ment and connectivity products.
BASIC/LAN 2.2 (Contact Closure) Ports (2)
Also used to connect your UPS to any workstation or server. Use
with Tripp Lite software and cabling to automatically save open
files and shut down equipment during a blackout. These ports use
contact-closure signals to indicate line-fail and low-battery status.
External Battery Connector
Use this to connect additional Tripp Lite battery packs for addi-
tional runtime. Refer to the label next to the connector for
appropriate Tripp Lite battery pack to connect. Refer to instruc-
tions available with the battery pack for complete connection
information and safety warnings.
LAN Interface DIP Switches
DIP Switches #1 and #2 activate or deactivate remote shutdown
through the “BASIC” Contact-Closure Ports. See “DB9 Port Con-
nection” on page 4 for which switch controls which port. Note: DIP
Switch #3 has no function. DIP Switch #4 serves as
the UPS’s “System Enable Switch.”
9911081 230V Smartpro 2200T OM.p65 11/24/99, 12:00 PM6

7
Specifications
Storage & Service
Storage
Turn your UPS OFF: first engage the ON/Standby Switch and release it to place
your UPS in the “Standby” mode; then set the System Enable Switch (Jumper #4,
UPS rear panel) to "DISABLE" (down); finally, disconnect the UPS power cord
from the wall outlet. If you plan on storing your UPS for an extended period of
time, recharge the UPS batteries once every three months. Follow steps #1 and
#3 in the Quick Installation section and allow the UPS to charge from 4 to 6 hours.
If you leave your UPS batteries discharged for an extended period of time, they
will suffer permanent loss of capacity.
Service
If returning your UPS to Tripp Lite, please carefully pack the UPS using the
ORIGINAL PACKING MATERIAL that came with the unit. Enclose a letter
describing the symptoms of the problem. If the UPS is within the 2 year warranty
period, enclose a copy of your sales receipt.
Smart 2200XLT
Output Capacity (VA/Watts): 2200/1750
Battery Runtime (Half Load/Full Load) Minutes: 27+/11+*
Battery Recharge Time: 2-4 hrs.*
Approvals: UL, cUL
Nominal Input Voltage/Frequency: 208V/60 Hz
On-Line Input Voltage Range: 173-250 volts
Voltage-Regulated Output Voltage Range: 230V ± 9%
On-Battery Output Voltage Range: 230V ± 5%
Output Waveform —Line Mode: filtered sinewave
Output Waveform —Battery Mode: PWM sine wave
AC Surge Suppression : exceeds IEEE 587
Cat. A & B standards
AC Noise Attenuation: >40 dB
AC Protection Modes: H to N, H to G, N to G
*Runtime can be extended with the connection of the appropriate Tripp Lite external battery packs. With the addition of
external battery packs, battery recharge time will increase.
9911081 230V Smartpro 2200T OM.p65 11/24/99, 12:00 PM7

8
93-1503 (9911081)
1111 W. 35th Street
Chicago, IL 60609 USA
Customer Support: [phone]
www.tripplite.com
9911081 230V Smartpro 2200T OM.p65 11/24/99, 12:00 PM8