Trotec BE15 User manual
TRT-BA-BE15-TC-001-EN
BE15
EN
OPERATING MANUAL
VOLTAGE DETECTOR
1 EN
voltage detector BE15
Table of contents
Notes regarding the operating manual.................................1
Safety .....................................................................................1
Information about the device................................................2
Transport and storage...........................................................3
Operation ...............................................................................3
Maintenance and repair ........................................................5
Disposal .................................................................................5
Notes regarding the operating manual
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information (e.g.
material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
operating manual must be observed.
You can download the current version of the operating manual
and the EU declaration of conformity via the following link:
BE15
https://hub.trotec.com/?id=41857
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!
Warning
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future
reference.
This appliance can be used by children aged from
8years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
• Do not use the device in potentially explosive rooms.
• Do not use the device in aggressive atmosphere.
• Protect the device from permanent direct sunlight.
• Do not remove any safety signs, stickers or labels from the
device. Keep all safety signs, stickers and labels in legible
condition.
• Do not open the device with a tool.
• Observe the storage and operating conditions as given in
the Technical data chapter.
Intended use
Only use the device for detecting alternating voltages whilst
adhering to the technical data.
To use the device for its intended use, only use accessories and
spare parts which have been approved by Trotec.
EN 2
voltage detector BE15
Improper use
The device is not suitable for the accurate measurement of
voltages. Do not try to detect direct current voltages with the
device.
The device may not be used in potentially explosive
atmospheres, when wet or very humid.
Personnel qualifications
People who use this device must:
• be aware of the dangers that occur when working with
electric devices in damp areas.
• have read and understood the operating manual, especially
the Safety chapter.
Residual risks
Danger
Electric shock from insufficient insulation. Check the
device for damages and proper functioning before each
use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!
Do not use the device when the battery compartment
or the housing are open.
Danger
Electric shock from contact with live parts. Do not
touch any live parts. Secure neighbouring live parts by
insulating them or switching them off.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Caution
Keep a sufficient distance from heat sources.
Note
To prevent damages to the device, do not expose it to
extreme temperatures, extreme humidity or moisture.
Note
Do not use abrasive cleaners or solvents to clean the
device.
Information about the device
Device description
The voltage detector detects alternating voltage (AC) and signals
it to the user via a flashing LED and an acoustic signal.
The device can be used for finding a cable break or determining
the presence of alternating voltage in fuses, wires and cables.
Additionally the measuring device is equipped with an
integrated LED torch.
Device depiction
1 2 3
5
6
7
4
No. Designation
1 Device power button/ sensitivity selection button
2 Clip
3 LED torch power button
4 LED torch
5 Battery compartment cover
6 Battery compartment
7 Measuring tip
3 EN
voltage detector BE15
Technical data
Parameter Value
Detection range 200 V AC to 1000 V AC
24 V AC to 1000 V AC
Overvoltage category CAT III 1000 V
CAT IV 600 V
Degree of pollution 2
Battery type 2 x 1.5 V batteries AAA (Micro)
Weight 48.5 g
Ambient conditions 0°C to 40°C
with max. 80% RH
Storage conditions -10°C to 60°C
with max. 80% RH
Scope of delivery
1xVoltage detector BE15
2 x 1.5 V battery AAA (Micro)
1 x Quick guide
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
For transporting the device use a suitable bag to protect it from
external influences.
Storage
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat
• protected from dust and direct sunlight
• with a cover to protect it from invasive dust if necessary
• The storage temperature is the same as the range given in
the Technical data chapter.
• Remove the batteries from the device.
Operation
Inserting the batteries
Note
Make sure that the surface of the device is dry and the
device is switched off.
Insert the batteries contained in the scope of delivery (2 x 1.5V
AAA) before first use.
Please proceed as follows to insert the batteries into the device:
1. Press down the clip(2).
2. Pull the battery compartment cover(5) back.
3. Insert the batteries into the battery compartment(6) with
correct polarity.
4. Slide the battery compartment cover(5) back onto the
device and make sure that the clip(2) engages.
Switching the device on
1. Switch the device on by pressing the device power
button(1).
ðA brief beep is emitted, and the measuring tip(7) lights
up green.
Info
After switch-on, the device's measurement sensitivity
is always set to 200V to 1000V. In order to detect
lower ACvoltages, you have to select sensitivity level2
before starting the measurement.
EN 4
voltage detector BE15
Setting the measurement sensitivity
The device BE15 has two sensitivity levels.
Sensitivity level ACvoltage
measuring range
LED colour
measuring tip
1 200 V to 1000 V green
2 24 V to 1000 V orange
Please proceed as follows to change the sensitivity level:
1. Switch the device on.
ðAfter switch-on, the device's measurement sensitivity is
set to 200V to 1000V.
2. Briefly press the sensitivity selection button(1) once.
ðThe measuring tip lights up orange, and sensitivity
level2 is set.
ðThe device's measurement sensitivity is now set to 24V
to 1000V.
24 V – 1000 V 200 V – 1000 V
~
~
Checking the device's functionality before measuring
üCharged batteries have been inserted into the device.
1. Switch the device on.
2. Check the voltage detector for proper functioning before
each measurement. To do so, hold the measuring tip (7)
to a known source of voltage.
ðThe measuring tip (7) flashes red.
ðA repetitive beep is emitted.
ðYou can now use the device to detect ACvoltages.
Detecting ACvoltage
After successfully testing the device's functionality, you can use
the device to detect ACvoltages. To do so, please proceed as
follows:
üCharged batteries have been inserted into the device.
üThe device's functionality has been tested successfully.
1. Switch the device on.
2. Select the desired sensitivity level.
3. Hold the device near the ACvoltage source to be
measured.
ðIf there is an ACvoltage within the selected sensitivity
range present at the source, the measuring tip(7) will
flash and a repetitive beep will be emitted.
5 EN
voltage detector BE15
Switching on the torch
Please proceed as follows to use the torch:
üCharged batteries have been inserted into the device.
1. Press and hold the LED torch power button(3).
ðThe LED torch(4) will be illuminated for as long as the
LED torch power button(3) is pressed.
2. Let go of the LED torch power button(3) to switch off the
LED torch.
Maintenance and repair
Cleaning
Clean the device with a soft, damp and lint-free cloth. Ensure
that no moisture enters the housing. Do not use any sprays,
solvents, alcohol-based cleaning agents or abrasive cleaners,
but only clean water to moisten the cloth.
Repair
Do not modify the device or install any spare parts. For repairs
or device testing, contact the manufacturer.
Disposal
The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.
Li-Ion
In the European Union, batteries and accumulators must not be
treated as domestic waste, but must be disposed of
professionally in accordance with Directive 2006/66/EC of the
European Parliament and of the Council of 6September 2006
on batteries and accumulators. Please dispose of batteries and
accumulators according to the relevant legal requirements.
Trotec GmbH & Co. KG
Grebbener Str. 7
D-52525 Heinsberg
+49 2452 962-400
+49 2452 962-200
www.trotec.com
This manual suits for next models
1
Table of contents
Other Trotec Security Sensor manuals
