Trust ICS-2000 User manual

www.trust.com

ICS-2000
OCTOPUS CONTROL STATION
CONFIGURATION OF THE
SECURITY SYSTEM
Item 71110 Version 1.0
Visit www.trust.com
for the latest instructions

ICS-2000 INTERNET CONTROL STATION
3
Make sure your phone / tablet is connected to the same network as the ICS-2000
A
To verify this, check in the settings if the connectivity is displaying local. If this is not the case,
connect to the Wi-Fi network of the router to which your ICS-2000 is connected to.
1. Preparation
A
A

ICS-2000 INTERNET CONTROL STATION
4
BUnscrew the siren cap, open the contact sensors and remove the motion sensor(s) from the
holders.
CKeep the included pin ready for pressing the pairing button.
B
C

ICS-2000 INTERNET CONTROL STATION
5
By connecting the security system with the Octopus control station it is possible to operate it with your
smartphone / tablet and receive push notifications when the alarm is activated.
If you already have a working Trust Smart Home security system first clear the sirens memory
by pressing the learning button for 2 seconds (until the LED starts flashing), then release the button
and press it again for 6 seconds. Release it again and press once briefly. The LED will flash 5 times to
confirm the deletion.
APress the SECURITY button in the menu bar
BPress the + button at the top of the screen to add a new security system.
CA dialog is shown to put the siren in learning mode. (Refer to the manual of the siren howto put it
into learning mode.) Press CONNECT after activating the learning mode.
1.1 Connect a new security system
A
B
C
learn button
2 sec
6 sec
1 sec

ICS-2000 INTERNET CONTROL STATION
6
DThe Siren is now being paired to the control station
EThe Siren is now paired to the control station
FAnother dialog is displayed to add a device. Press the DOOR / WINDOW SENSOR. A new dialog is
displayed to give a name for the door / window sensor. Enter a name and press ADD.
Cause of environmental factors, you may need to repeat the pairing, choose RETRY
D
E
F

ICS-2000 INTERNET CONTROL STATION
7
GPress the SET button on the sensor for about 2 sec. Then press the CONNECT button.
HThe sensor is paired to the control station
IAnother dialog is displayed to add a device. Press the MOTION SENSOR. A new dialog is displayed to give
a name for the motion sensor. Enter a name and press ADD.
JPress the SET button on the sensor for about 2 sec. Then press the CONNECT button.
G
H
I

ICS-2000 INTERNET CONTROL STATION
8
KAnother dialog is displayed to add a device. When you are done adding sensors, press the button I’M
DONE. The security system is now being added. This may take some time (1-2 minutes)
LOptional: Add Remote.
It is not a requirement to add the remote control. You can control the security system completely with
the App.
To add the remote follow the steps in section 1.4
J
J
K
K

ICS-2000 INTERNET CONTROL STATION
9
After adding the security system the overview screen will be displayed
AOn / O switch: With this switch the system can be turned on or o.
BSystem Status: The status of the system is shown. There are six dierent states.
Security System: The security system is o. The sensors will not trigger the alarm.
Sensors check: The status of the sensors are checked and the walk-out time is started
Walk-out time: The walk-out time is active. The sensors will not trigger the alarm until for ~ 85 sec.
Security system on: The security system is on.
Activation Error: One of the sensors is not closed or an anti-tamper switch is not closed properly.
Alarm goes o: The security system goes o.
1.2 Security system interface
A
B

ICS-2000 INTERNET CONTROL STATION
10
CSensor status: When the system is turned on or o, the status of the sensors are checked and
displayed.
: Sensor is active Anti-tamper switch is activated
: Sensor is not active : Sensor has no connection
: Battery of the sensor is almost empty
When the system is activated and one of the sensors or siren indicates an error the status of the
system will change to activation error. Turn the system o and on again. If still not resolved: Make
sure all sensors and the siren are correctly mounted according to the instructions. Replace batteries
when the sensor or siren continues to give a connection error
C