VADDIO RoboSHOT 12 User manual

© 2014 Vaddio - All Rights Reserved. RoboSHOT QCCU Systems - Document Number 342-0797 Rev A
VADDIO™ROBOSHOT™ SERIES CAMERAS
RoboSHOT 12 and RoboSHOT 30, HD Robotic PTZ Camera Systems
featuring the Quick-Connect™ Universal CCU Interface
System Model and Part Numbers
RoboSHOT 12 QCCU System, 999-9907-000 (North America), 999-9907-001 (Int’l)
RoboSHOT 30 QCCU System, 999-9917-000 (North America), 999-9917-001 (Int’l)
RoboSHOT 30 QCCU System, 999-9917-000W (North America), 999-9917-001W (Int’l)
(Note: The W suffix on the part number indicates white version of the RoboSHOT 30)
RoboSHOT 30
High-definition Robotic PTZ Camera for Medium to Large Venues
Featuring 30X Optical Zoom Lens and Tri-Synchronous Motion
RoboSHOT 12
High-definition Robotic PTZ Conferencing Camera Featuring a 12X,
73º Wide Angle Optical Zoom Lens and Tri-Synchronous Motion
Quick-Connect Universal CCU System Interface
Installation and User Guide

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 2 of 48
Inside Front Cover - Blank

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 3 of 48
TABLE OF CONTENTS
Overview......................................................................................................................................................................................4
Unpacking the Camera Systems..................................................................................................................................................6
Image: RoboSHOT 12 HD PTZ Camera.............................................................................................................................7
Image: RoboSHOT 30 HD PTZ Camera.............................................................................................................................8
Image: RoboSHOT 12X and 30X Rear Panel Connections ................................................................................................9
Rear panel connections are identical for both models (RoboSHOT 12 shown)........................................................................9
Anatomy of the Universal CCU ..................................................................................................................................................10
Image: Front Panel CCU Controls.....................................................................................................................................10
Image: Close up View of the Universal CCU Control Panel ...............................................................................................10
Image: Rear Panel CCU Connections and Controls (left to right)......................................................................................11
RoboSHOT and Quick-Connect Universal CCU Control Menus ................................................................................................12
Menu Organization.............................................................................................................................................................12
Image: Main Menu Page ...................................................................................................................................................12
Image: Shutter and Noise Reduction Menu.......................................................................................................................12
Image: Wide Dynamic Range Menu..................................................................................................................................12
Image: Cat-5 Adjustment Menu Page ...............................................................................................................................12
Image: LCD Screen Adjustment Screen............................................................................................................................13
System Configuration Example..................................................................................................................................................13
Diagram: Basic Connectivity Example...............................................................................................................................13
Installation Basics:......................................................................................................................................................................14
Setting the RoboSHOT Camera.................................................................................................................................................15
Drawing: Dip Switch and Resolution Label on the Bottom of the RoboSHOT....................................................................15
Setting the RoboSHOT Switch Gear:.....................................................................................................................................15
Dip Switch Settings Further Explained (DSSFE):...................................................................................................................15
Setting the CCU .........................................................................................................................................................................15
Controlling the Camera ..............................................................................................................................................................16
IR Remote Commander .....................................................................................................................................................16
Telnet Control.....................................................................................................................................................................16
The Screen Shot Tour................................................................................................................................................................17
Compatible Web Browsers.....................................................................................................................................................17
DHCP IP Set-up (Dynamic Host Configuration Protocol).......................................................................................................17
Static IP Set-up: .....................................................................................................................................................................17
Screen Shot: Login............................................................................................................................................................17
Screen Shot: Camera Control Page..................................................................................................................................18
Screen Shot: Storing Presets............................................................................................................................................19
Screen Shot: Admin login from the Camera Control Page ................................................................................................20
Screen Shot: Admin Menu - Camera Settings...................................................................................................................21
Screen Shot: Admin Menu - Room Labels ........................................................................................................................22
Screen Shot: Admin Menu - DHCP Network Configuration...............................................................................................23
Screen SHOT: Admin Menu - Static IP Configuration.......................................................................................................23
Screen SHOT: Admin Menu - Security..............................................................................................................................24
Screen Shot: Admin Menu - Diagnostics...........................................................................................................................24
Screen Shot: Admin Menu - System .................................................................................................................................25
Screen Shot: Admin Menu - Update Confirmation.............................................................................................................26
Screen Shot: Admin Menu - Update in Progress...............................................................................................................26
Screen Shot - Admin Menu - Help......................................................................................................................................27
General Specifications ...............................................................................................................................................................28
Communication Specification.....................................................................................................................................................29
RoboSHOT Command List.....................................................................................................................................................29
Telnet Serial Command API.......................................................................................................................................................34
Telnet Command List.............................................................................................................................................................34
Compliance and CE Declaration of Conformity - RoboSHOT HD PTZ Cameras.......................................................................43
Compliance and CE Declaration of Conformity - Quick-Connect Universal CCU.......................................................................44
Warranty Information..................................................................................................................................................................45
Appendix 1: Cable Pin-outs for the Quick-Connect CCU System .............................................................................................46

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 4 of 48
O VERVIEW
The extraordinary RoboSHOT HD PTZ cameras are professional
quality with super high quality imaging, fine detail and exceptional color
reproduction. This camera offers integrators, dealers and end users
with an incredible improvement over other conferencing and large
venue cameras available today. The RoboSHOT Platform consists of
two models; the RoboSHOT 12 and the RoboSHOT 30.
The RoboSHOT 12 is perfect for small to medium sized conference
rooms. This model features a 12X optical zoom and a 73° wide angle
horizontal field of view, which provides incomparable support for
applications including UCC applications, videoconferencing, distance
learning, lecture capture, telepresence and more!
The RoboSHOT 30 camera performs brilliantly in medium to large
rooms. It features a 30X optical zoom with an impressive 2.3° tele end
to 65° wide end horizontal field of view and provides exceptional
support for applications including House of Worship productions, large
auditorium A/V systems, large distance learning classrooms, live event
theatres with IMAG systems, large lecture theatres with lecture capture
and more!
The key features of both RoboSHOT cameras are Tri-Synchronous
Multi-Axis Motion and the Advanced Image Sensor, lens and ISP
(image signal processor) combination. The Tri-Synchronous Motion
algorithm in the RoboSHOT cameras is capable of moving all three
(pan, tilt and zoom) axes simultaneously. The algorithm calculates the
position and velocity of the smooth, direct-drive motor movements
between the presets so pan, tilt and zoom arrive at the preset subject
simultaneously, which finally allows for smooth and manageable on-air
camera movements. Yep, there’s no more pan/tilt, then zoom like other
PTZ cameras available today.
The lens, image sensor and ISP are the real magic behind the RoboSHOT’s remarkable video performance
characteristics. Both cameras use the latest generation Exmor® 1/2.8”, 2.34 Megapixel, Full HD (1080p/60) high-
speed, low noise CMOS image sensor combined with a new ISP, produces vivid, realistic and accurate color with
extremely fast, razor sharp automatic focus and auto iris routines.
All RoboSHOT’s are equipped with an Ethernet port and a built-in web server, which allows the user to control the
camera functions on an internal web page with a browser from anywhere in the world, or in the same room, over
the IP network. Telnet, IR Remote and RS-232 control for the camera are available to satisfy almost any system
control requirements.
The RoboSHOT platform paired with the Quick-Connect Universal
CCU uses the Vaddio EZCamera™ Cat-5 Cable System to
transport HSDS™ (differential video), power and control to and
from the camera over standard Cat-5 cabling up to 500’ (152.4m)
with virtually no loss in video quality or any without latency. The
most flexible attributes the Universal CCU has is at the outputs.
The Universal CCU has simultaneous HD-SDI, HDMI and HD Analog component (YPbPr) outputs, all of which can
be used concurrently. Resolution throughput from the camera ranges up to and including 1080p/60 on all outputs.
The back-lit blue LED screen displays up to eight (8) parameters at a time and the camera’s model number so the
interrelationship of the controls can easily and quickly be read and understood.
The RoboSHOT cameras were designed for the times and represent a new era in specifying and integrating
professional quality cameras into A/V and conferencing system configurations. In short, it has never been easier
to integrate cameras into any environment than with the RoboSHOT HD Cameras.
RoboSHOT 30
HD PTZ Camera on Mount
RoboSHOT 12
HD PTZ Camera on Mount
Quick-Connect Universal CCU
(shown with included rack ears)

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 5 of 48
Intended Use:
Before operating the device, please read the entire manual thoroughly. The system was designed, built and tested
for use indoors with the power supply provided. The use of a power supply other than the one provided or outdoor
operation hasn’t been tested and may damage the device and/or create an unsafe operating condition.
Save These Instructions:
The information contained in this manual will help you install and operate your product. If these instructions are
misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product
drawings (DWG and PDF) for the Vaddio product lineon the Vaddio website. These documents can be downloaded
from www.vaddio.com free of charge.
Important Safeguards:
Read and understand all instructions before using. Do not operate any device if it has been dropped or damaged.
In this case, a Vaddio technician must examine the product before operating. To reduce the risk of electric shock,
do not immerse in water or other liquids and avoid extremely humid conditions.
The RoboSHOT HD PTZ camera connectivity for all signals (video, power and control) is over Cat-5 cable
(ubiquitously referred to as Cat-5 or Cat-5e). For best results, please use quality Cat-5e cable and real RJ-45
crimpers. Unlike phone and data lines that use the four center conductors (pairs 3 & 6 and pairs 4 & 5), the Vaddio
EZCamera systems use all of the pins in most configurations. When terminated correctly The Vaddio Cat-5e
solution provides for the utmost in flexibility for HD video system design, integration and ease of installation.
Use only the power supply provided with the system. Use of any unauthorized or
extended DC power supplies will void any and all warranties.
Please do not use “pass-thru” type RJ-45 connectors. These pass-thru type
connectors do not work well for professional installations and can be the cause of
intermittent connections which can result in the RS-232 control line failing and
locking up, and/or compromising the HSDS (high speed differential signals). For
best results please use standard RJ-45 connectors and test all cables for proper
pin-outs prior to use and connection to Vaddio Cat-5e products.

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 6 of 48
U NPACKING THE C AMERA S YSTEMS
Carefully remove the product and all of the included parts from the packaging.
Identify the following parts for each camera:
RoboSHOT 12 QCCU System
Part Number 999-9907-000 (North America)
One (1) RoboSHOT 12 HD PTZ Camera (998-9900-000)
One (1) Thin Profile Wall Mount (535-2000-240) with Mounting Hardware
One (1) IR Remote Commander (998-2100-000)
One (1) EZCamera Control Adapter (998-1001-232)
One (1) Quick-Connect Universal CCU Interface (998-1105-034)
One (1) 36 VDC, 2.78 Amp Switching Power Supply with North American AC Cord Set
One (1) 806-819 Gray RJ-45 Dust Cap (for 36VDC RJ-45 Port on camera)
One (1) 3-pin Molex 5.0mm Euro style Connector
One (1) Quick Setup Guide
RoboSHOT 30 QCCU System
Part Number 999-9907-001 (International)
One (1) RoboSHOT 12 HD PTZ Camera (998-9900-000)
One (1) Thin Profile Wall Mount (535-2000-240) with Mounting Hardware
One (1) IR Remote Commander (998-2100-000)
One (1) EZCamera Control Adapter (998-1001-232)
One (1) Quick-Connect Universal CCU Interface (998-1105-034)
One (1) 36 VDC, 2.78 Amp Switching Power Supply
One (1) Euro Power Cord
One (1) UK Power Cord
One (1) 806-819 Gray RJ-45 Dust Cap (for 36VDC RJ-45 Port on camera)
One (1) 3-pin Molex 5.0mm Euro style Connector
One (1) Quick Setup Guide
RoboSHOT 30 QCCU System
Part Number 999-9917-000 (North America)
One (1) RoboSHOT 30 HD PTZ Camera (998-9910-000)
One (1) Thin Profile Wall Mount (535-2000-240) with Mounting Hardware
One (1) IR Remote Commander (998-2100-000)
One (1) EZCamera Control Adapter (998-1001-232)
One (1) Quick-Connect Universal CCU Interface (998-1105-034)
One (1) 36 VDC, 2.78 Amp Switching Power Supply with North American AC Cord Set
One (1) 2-pin Molex 5.0mm Euro style Connector
One (1) 806-819 Gray RJ-45 Dust Cap (for 36VDC RJ-45 Port on camera)
One (1) Quick Setup Guide
RoboSHOT 30 QCCU System
Part Number 999-9917-001 (International)
One (1) RoboSHOT 30 HD PTZ Camera (998-9910-000)
One (1) Thin Profile Wall Mount (535-2000-240) with Mounting Hardware
One (1) IR Remote Commander (998-2100-000)
One (1) EZCamera Control Adapter (998-1001-232)
One (1) Quick-Connect Universal CCU Interface (998-1105-034)
One (1) 36 VDC, 2.78 Amp Switching Power Supply
One (1) Euro Power Cord
One (1) UK Power Cord
One (1) 2-pin Molex 5.0mm Euro style Connector
One (1) 806-819 Gray RJ-45 Dust Cap (for 36VDC RJ-45 Port on camera)
One (1) Quick Setup Guide

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 7 of 48
Image: RoboSHOT 12 HD PTZ Camera
Camera Front View with Feature Call-outs
1) Camera and Zoom Lens: This RoboSHOT model features a 12X optical zoom lens (12X in Super-Wide mode
and 10X in normal mode) that is built around an Exmor 1/2.8-Type, high-speed, low noise image sensor with a total
of 2.34 megapixels for exceptionally precise HD video image acquisition in a small to medium sized conference
room.
2) Camera Support Arm: The RoboSHOT cameras use a single control arm for pan and tilt movements. Both
ends of the cast control arm are anchored with silent and smooth BLDC (brushless DC) direct drive motors. These
motors provide ultra-accurate and fast camera positioning and are capable of the slowest of crawls, which are
suitable for on-air use.
3) IR Sensors: IR sensors are built into the front of the RoboSHOT to receive IR signals from the IR Remote
Commander suppliedwith the camera. The IR sensors sit behind the Makrolon IR Window on the front of the base.
4) Multi-Color LED:
The multi-colored LED indicates the use states of the camera:
Purple LED is for Boot-up and Standby modes.
Blue LED is for normal operation and is a power on, ready condition.
The blue LED will blink when the camera receives a valid IR command.
Solid red LED is to indicate a tally function illuminating when the camera is on-air.
Blinking red LED indicates a fault condition.
Yellow LED illuminates during a firmware update.
5) Logo: Really Cool Logo Badge (RCLB) is located on the IR Window.
6) Camera Base: Cast zinc alloy base for strength and stability, powder coated for toughness with fine texture.
②
①
③
④
⑤
⑥
Color: Silver and Black

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 8 of 48
Image: RoboSHOT 30 HD PTZ Camera
The differences between the 12X model and the 30X models center around the power of the optical zoom lens and
overall color of the camera models. The 30X is available in both black and white.
1) Camera and Zoom Lens: This RoboSHOT model has a powerful 30X optical zoom lens that is built around
an Exmor 1/2.8-Typ, high-speed, low noise image sensor with a total of 2.34 megapixels for vibrant, detailed HD
video image acquisition in a large to medium sized room.
2) Camera Support Arm: The RoboSHOT cameras use a single control arm for pan and tilt movements. Both
ends of the cast control arm are anchored with silent and smooth BLDC (brushless DC) direct drive motors. These
motors provide ultra-accurate and fast camera positioning and are capable of the slowest of crawls, which are
suitable for on-air use.
3) IR Sensors: IR sensors are built into the front of the RoboSHOT to receive IR signals from the IR Remote
Commander suppliedwith the camera. The IR sensors sit behind the Makrolon IR Window on the front of the base.
4) Multi-Color LED:
The multi-colored LED indicates the use states of the camera:
Purple LED is for Boot-up and Standby modes.
Blue LED is for normal operation and is a power on, ready condition.
The blue LED will blink when the camera receives a valid IR command.
Solid red LED is to indicate a tally function illuminating when the camera is on-air.
Blinking red LED indicates a fault condition.
Yellow LED illuminates during a firmware update.
5) Logo: Really Cool Logo Badge (RCLB) is located on the IR Window.
6) Camera Base: Cast zinc alloy base for strength and stability, powder coated for toughness with fine texture.
Color: Black
Also Available in White
②
③
④
⑤
⑥
①

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 9 of 48
Image: RoboSHOT 12X and 30X Rear Panel Connections
Rear panel connections are identical for both models (RoboSHOT 12 shown).
1) CAMERA SETTINGS: Dip switch settings for IR remote frequency, baud rate and image flip can be configured
with these switches. See the Switch Settings page for additional information.
2) HD VIDEO SELECT: A rotary switch allows the user to choose the HD video output resolution. See the Switch
Settings page for additional information.
3) NETWORK CONTROL Port: The Ethernet 10/100 port allows the camera to be controlled from embedded
web server with a web browser or through Telnet session.
4) RS-232 Port: The RS-232 port accepts modified VISCA protocol for camera control over a Cat-5e cable. This
port also acts as an IR Forwarding port with the Quick-Connect SR or Quick-Connect DVI/HDMI interfaces, which
allows the user to transmit 3
rd
party IR signals through camera to the head-end.
5) EZ-POWER VIDEO Port: The EZ-Power Video port supplies 24 VDC power to the camera and delivers HD
video back to the Quick-Connect interface using high speed differential signaling over Cat-5e cable.
6) 36 VDC FOR CCU ONLY: The CCU power port is only used with Quick-Connect Universal CCU and is shipped
with a dust cap inserted in the connector The EZ-Power Video port, becomes the Video output to the CCU, and the
RS-232 connects normally. Please see the system diagrams of the CCU systems to fully understand the wiring.
NOTE: Remove the dust cap just prior to connecting the 36 VDC Cat-5e cable. Please do not plug this
cable into the EZ-POWER VIDEO RJ-45.
②
③
④
⑤
⑥
①

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 10 of 48
A NATOMY OF THE U NIVERSAL CCU
The Universal CCU will automatically sense the connected camera and initialize the firmware for that camera. The
next section will look at the controls and how they are laid out for easy access.
Image: Front Panel CCU Controls
Front Panel Controls (left to right):
5-Line Blue Back-lit LED: Displays up to 8 parameters at a time so the interrelationship of the controls can
easily and quickly be read and understood.
Tally Light: A contact closure on the back panel lights the blue LED on front panel indicating which Universal
CCU and camera combination is the live Program in a multi-camera CCU installation. A tally command will
also be sent to the camera via RS-232 to light the LED on cameras with on-board tally lights
Image: Close up View of the Universal CCU Control Panel
Keypad Controls from (left to right): Touch the button for the parameter to be controlled and adjust the value
with the rotary encoder, then touch the cancel button to exit. When the rotary encoder button is touched, the
SELECT and CANCEL menu buttons will illuminate to remind the user to either…select or cancel.
Scenes A, B & C: Three user definable camera scenes (A, B & C) can be stored into microprocessor memory.
Whenlit(backlit blue button),thesceneisactivated. Tostore a scene,theuser adjusts thecontrolsandtouches
and holds the scene button down until the button blinks. To erase a scene press and hold the scene button
and the cancel button.
Auto White Balance: The Automatic White Balance controls/adjusts the color levels automatically when
engaged. Take it out of Auto to manually adjust the Red and Blue levels.
OPWB (One Push White Balance): When using OPWB, zoom in on a white subject, at least 60% of the image
must be white, touch the OPWB button and the coloration of the image will adjust to the white used in this shot.
Red & Blue Gain Controls: The Red and Blue Gain buttons in combination with the encoder adjust the red
and blue gain of the signal when Auto White Balance is disengaged.
Chroma: Chroma controls the overall color of the image being captured.
Bright: This is the overall luminance control for the image.
Gamma: Gamma adjusts the overall brightness of an image to compensate for the perception of luminance
and chroma.
Detail: The Detail control sharpens or softens objects in the frame. Works well when looking at text.
IRIS - Auto or Manual: The Auto Iris mode automatically adjusts the iris and gain of the camera. To manually
adjust the iris or gain, turn off this control. The Manual Iris control allows the user to set the iris manually to one
of the several settings available
Gain: The Gain control boosts the signal level when the iris is openall the way, and there is not enough lighting
available. To manually adjust the Gain, Auto Iris must be off. Use the Gain last to enhance the image.
Rotary Encoder: Use the encoder to adjust values after the button is selected. This makes for very quick
changes.
The Menu Buttons: There are other screens to be accessed other than the camera control screen. Use the
SELECT and CANCEL to enter other controls and exit other menus.

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 11 of 48
Image: Rear Panel CCU Connections and Controls (left to right)
Power Supply Input: The Universal CCU uses a 36VDC, 2.78 Amp power supply on a 5.5mm OD x 2.5mm
ID coaxial connector with a positive center.

36 VDC to Camera - RED RJ-45: Power is provided on a Cat-5 cable to the RoboSHOT 36 VDC RJ-45 marked
for CCU use only (see page 9). The power is regulated in the camera to 12 VDC.
RS-232 IN - GREEN RJ-45: RS-232 Input from ProductionVIEW™ console, Precision Camera Controller or
other custom camera control system. Daisy Chain topology is not supported.
RS-232 to Camera - BLUE RJ-45: RS-232 control is sent through this Cat-5 connection.
Tally on 2-pin Molex 5.0mm Euro-Style connector: Acontact closure lights the blue LED on front panel
showing which Universal CCU and camera combination is the live Program in a multi-camera CCU installation.
A tally command will also be sent to the camera via RS-232 to illuminate the LED on the cameras that have on-
board tally lights.
Camera Feature Switches: The CCU interface has an 8-position dip switch on the rear panel to allow for
certain functionality. All switches should be in the down position for default.
Dip Switch 1: Put up to allow Scene A to load upon start-up or boot up.
Dip Switch 5: Put up to access LCD Display Menu settings including Display Mode, Bias and Contrast.
Video from Camera - YELLOW RJ-45: The yellow RJ-45 receives the camera’s differential video signals from
the RoboSHOT’s EZ-POWER VIDEO jack (but there’s no power on the cable).
HD Video Outputs: The Universal CCU has 3 (three) simultaneous video output formats that are the same
resolution as the video inputs providing the ultimate in connectivity flexibility. The output formats include:
HD YPbPr on DE-15-F (HD15) - (supports up to/and including 1080p/60 - not limited)
HDMI on HDMI-F (supports up to and including 1080p/60)
HD-SDI on Edge Mount Carrier Class, Gold BNC-F (supports 3Gb/s Single Link 1080p/60 HD-SDI)
The Quick-Connect Universal CCU supports the resolutions with refresh rates of above 50 Hz (60, 59.94 and 50).

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 12 of 48
R OBO SHOT AND Q UICK -C ONNECT U NIVERSAL CCU C ONTROL M ENUS
The RoboSHOT cameras have individual firmware that auto loads when the camera is plugged in to the Universal
CCU and the CCU is turned on (Note: Always turn the camera on first so when the CCU wakes up, it will recognize
the RoboSHOT). The menus are organized as follows:
Menu Organization
Image: Main Menu Page
The Main Menu screen shows eight (8) prominent
parameters at a time. These controls are directly related to
the front panel buttons allowing for quick change access.
Simply touch the button of the control to be adjusted, and
spin the rotary encoder and watch the value of the control
on the display change in real-time. This screen does not
need a cursor since the control relates directly to a front
panel button.
Image: Shutter and Noise Reduction Menu
Access to the shutter speed is allowed in this menu. For the
most part, it can be left at the default unless challenging or
funky lighting demands the use of the shutter. On this
screen and the rest, the cursor is the “@” sign and the “>”
appears as the parameter is select and adjusted. Touch
cancel to return to the cursor mode.
Image: Wide Dynamic Range Menu
The controls on this screen work together to provide wide
dynamic range (WDR. The controls are used in conjunction
with the Auto Iris Mode (auto iris has to be on to use WDR).
The WDR controls include:
Wide Dynamic Range: ON/OFF
Display Brightness Level: 0 - 6, 0: Dark, 6: Bright
Brightness Compensation: 0 - 3, 0: Very Dark, 1: Dark, 2: Standard, 3: Bright
Compensation Level 0 - 2, 0: Low, 1: Medium, 2: High
Image: Cat-5 Adjustment Menu Page
The Cat-5 Adjustment Menu allows the operator to adjust
the skew of the Cat-5 Cable, the color space of the HDMI
output, Y-Gain and the Scene Configuration.
Adjust the skew of the Cat-5 cable (range of 1 to 16) to
compensatefordifferinglengths oftheCat-5 cablepairs
between the camera and CCU. This setting will usually
be best in the middle of the range of skew numbers
which pass acceptable video.
Set the HDMI Color Space to YCbCr for HDMI and to sRGB for DVI-D output.
The Y-Gain is for adjusting the video ±10 IRE at all outputs as needed for associated video equipment.
Preset Lighting Scene Configurations offer sample settings for fluorescent, incandescent and outdoor lighting
environments. Choose the scene (shown in the Screen Config description below) which looks best for the
situation and fine tune from there.
Main Control Menu
8-Most used Controls
displayed
For this Menu, put
Di
p
Switch 5 UP
CAT-5 CCU RoboSHOT 30
RED 65 GAMMA 48
BLUE 75 DETAIL 04
CHROMA 08 IRIS AUTO
BRIGHT 50 GAIN AUTO
CAT-5 CCU RoboSHOT 30
@Skew 8 Scene Config
HDMI YCbCr > 1: AUTO
YGain Def
CAT-5 Adjust Menu
With Skew, Color
Space Y-Gain and Six
p
reset Scene
Wide Dynamic
Range Menu
Shutter and Noise
Reduction Menu
Version Info Menu
LED Display Menu
For set up of front
panel LED display
LCD Display
Adjustment Menu
CAT-5 CCU RoboSHOT 30
@Shutter 60
NR 2
CAT-5 CCU RoboSHOT 30
@WIDE DYNAMIC RANGE OFF
DISPLAY BRIGHTNESS LEVEL 3
BRIGHTNESS COMPENSATION 2
COMPENSATION LEVEL 1

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 13 of 48
Scene Configurations:
Six (6) Generalized Scene Configurations have been added to allow the user to quickly run through preset lighting environment
scenes. The admin can set three (3) custom scenes as well. The following presets are included:
1) AUTO (full Auto)
2) Incand Lo (incandescent low)
3) Incand Hi (incandescent high)
4) Fluor Lo (fluorescent low)
5) Fluor Hi (fluorescent high)
6) Outdoor
Image: LCD Screen Adjustment Screen
Put DIP switch 5 in the up position to adjust the front panel LCD.
The controls provided on this menu include:
Display Mode: Normal (negative mode) and Inverted
(positive mode)
Bias: Serves as a brightness control.
Contrast: For overall adjustment of the LCD contrast. Set
these controls to taste with the idea of making the display
more readable.
When finished, put DIP switch 5 back in the down position.
S YSTEM C ONFIGURATION E XAMPLE
The Quick-Connect Universal CCU interface uses three (3) Cat-5e cables to supply power to the camera, return
differential video from the camera while providing bi-directional control signaling (RS-232) for the camera over a
distance of up to 500’ (152.4m).
Diagram: Basic Connectivity Example
RoboSHOT Camera Connected to Quick-Connect Universal CCU Interface, ProductionVIEW™ HD-SDI MV
Controller with built-in multi-viewer.
CAT-5 CCU RoboSHOT 30
@Disply Norml
Bias 1/9
Contrast 204
Rear View of
RoboSHOT
Camera
RS-232
RS-232 Cat-5e
36 VDC, 2.78 A
Power Supply
HD-SDI
Quick-Connect Universal CCU (Rear Panel)
ProductionVIEW HD-SDI MV
with built-in Multi-viewer
Network Connection for Camera Configuration
& Control (Embedded web server or Telnet)
Cat-5e Power to Camera ►
◄ Cat-5e Video to CCU
Multi-viewer Preview Monitor Program Monitor
HDMI Simulated Video Feeds
Three Cat-5e
cables up to 500’
(
152.4m
)
in len
g
th

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 14 of 48
I NSTALLATION B ASICS :
The RoboSHOT cameras include a Thin Profile Wall Mount for…wall mounting the camera. There
are options for IN-Wall™ mounts and IN-Ceiling™ Half-Recessed as well. The Cat-5 cabling
ideology is especially convenient for camera mounting when the camera location is not anywhere
near an AC outlet. Installation is simplified in that no custom 8-Pin mini-din cables or expensive
plenum coax cables or multi-pin cables or power outlets are required near the camera location. All
Cat-5 cabling is routed to the head-end using with standard straight through RJ-45 connectors (568B
termination). “Pass-thru” type RJ-45 connectors should be avoided like bad clichés.”
Step 1: Determine Camera Mount Location
When locating the camera, consider viewing angles, lighting conditions, possible line of site obstructions and check
for in-wall or in-ceiling obstructions where the camera is to be mounted. Pick a mounting location to optimize the
performance of the camera. After determining the optimum location of the camera system, route the required three
(3) Cat-5e cables from the camera location back to the head-end. Mark the Cables: POWER, VIDEO and
CONTROL.
Note: Please check all Cat-5 cables for continuity in advance of final connection (568B). Plugging the
Power Cat-5 cable into the wrong RJ-45 or using the wrong pin-out may cause damage to the camera
system and void the warranty, which is typically bad…mostly.
After determining the optimum location of the camera system, route the required Cat-5e cables from the camera to
the head-end Quick-Connect. Test and mark the cables accordingly.
The Cat-5e cables should feed-through the cable management slots provided by
all Vaddio mounting options. If the wall mount is to be mounted on a 2-gang wall
box, use the screws supplied with the wall box cover plate to attach the Thin
Profile Wall Mount Bracket. If mounting to drywall with wall anchors, use the four
(4) quality wall anchors and screws provided.
The mounting holes are slotted and are 90° opposing to provide easy leveling.
Level the mount and place the camera on the mount. Check the level again to
avoid any of those weird Batman like camera angles. Use the provided ¼”-20 x
.375” mounting screw to attach the Camera to the mount.
Step 2: System Wiring
Follow the sample wiring diagrams for connecting the Cat-5e cables to the camera and Quick-Connect Universal
CCU Interface. Additional diagrams are available on the Vaddio website.
Connect the camera side as follows:
First, remove the dust cap on the Power RJ-45 and connect the POWER Cat-5e to the 36 VDC FOR CCU
ONLY RJ-45 on the RoboSHOT.
Connect the VIDEO Cat-5e to the EZ-POWER VIDEOV RJ-45 on the RoboSHOT (Only differential video is
transported over this Cat-5e - there is no power is on this wire).
Connect the RS-232 control Cat-5e to the “RS-232 IN” RJ-45 on the RoboSHOT camera.
Connect the Universal CCU side as follows:
Connect the VIDEO Cat-5 cable to the VIDEO FROM CAMERA RJ-45 jack (yellow) on the CCU.
Connect the RS-232 Cat-5 cable to the RS-232 TO CAMERA RJ-45 (Blue) on the CCU.
With the CCU not plugged into a power source, connect the POWER Cat-5e cable
Step 3: It’s alive… Plug the 36 VDC adapter into a power source and connect the DC power connector to the
CCU. If all the connections are good, the CCU will light up and look for the camera. The camera will boot up, twitch
a bit, and move to the home position. The CCU will find the camera and load the RoboSHOT control protocols. If
using a Vaddio controller, connect it to the RS-232 IN RJ-45 and turn on the controller. To ensure proper continuity
of control, the RS-232 controller (control system or joystick) should be powered on after the CCU and camera.
Important Note: Please refrain from dousing the CCU and RoboSHOT with and type of commands while
they are booting up. Wait until the boot cycle of the camera is finished. It has a Linux OS, so let it boot.
Use a level to
level the mount…

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 15 of 48
IR 1
1 & 2 UP
ON
DIP SWITCH SETTINGS
8
1234567
HD VIDEO RESOLUTION SELECT
720p/59.94
1080i/59.94
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1080p/59.94
1080i/60
1080p/60
720p/50
21 5 4
3768
IR 2
ON IR 3 ON
IR
OUT
OFF
BAUD
9600
bps
38,400
bps 1080i/50
1080p/50
7
OFF 8 OFF
IMAGE
FLIP
OFF
ON
SUPER
WIDE
OFF
ON
720p/60
720p/30
1080p/30
720p/25
1080p/25
SETTING THE ROBOSHOT CAMERA
The RoboSHOT cameras control the resolution of the video signal sent back to the Quick-Connect interface. There
is, as explained on the page 9, a rotary switch to set the HD video resolution and a set of eight (8) dip switches that
determine certain camera functions. See the drawing and description on how to setup the camera.
Drawing: Dip Switch and Resolution Label on the Bottom of the RoboSHOT
Setting the RoboSHOT Switch Gear:
1) Set the desired and available HD output resolution for the camera with the Rotary Switch.
2) Set the IR control frequency of the camera if it is to respond to the IR remote control.
3) If using the IR forwarding features with a 3rd party codec remote, set the IR OUT switch to ON (SW3).
4) If inverting the camera, turn the IMAGE FLIP ON (SW4).
5) For the RoboSHOT 12X model only, set the Super-wide mode to ON for a 12X, 73º horizontal super-wide
angle of view. Normal mode will produce 67.2º horizontal field of view (HFOV). The RoboSHOT 30 does not
have a Super Wide mode.
6) Set the Baud Rate dip switch (SW6) to 9600bps for most applications. Default is 9600 bps systems.
7) Setting all dip switches DOWN with a power cycle loads the default camera settings. Return dips to desired
operating position after power cycle.
Note: Switches 7 & 8 are reserved for future use.
Dip Switch Settings Further Explained (DSSFE):
IR 1, 2 and 3 (SW 1 &2): A single IR remote has the capability of operating up to three different PTZ cameras in a
room. Use these selector dip switches and the selector buttons at the top of the IR remote to select the frequency.
IR OUT on/off (SW3): The IR output is sent out on the RS-232 RJ-45 jack on the back of the camera. Turning on
the IR output will allow IR signals to be transmitted over the Cat-5 cable to the head end. When using RS-232 control
or Vaddio CCU controllers (also via RS-232), turn the IR OUT to OFF (up).
Image Flip (SW4): To invert the camera, turn the IMAGE FLIP ON (switch down).
Super-Wide Mode: Super-wide works only with the RoboSHOT 12 model and allows the camera to switch from
67.3º wide end HFOV to a Super Wide 73º wide end HFOV.
Baud Rate (SW6): The options for baud rate are either 9600 or 38,400 bps. The 9600 bps works best with Cat-5e
over distance. Use 38,400 bps for short control lines only.
Dip Switches (SW7 & 8): Not used for operation, please leave these dip switches up or in the OFF position.
SETTING THE CCU
Optimizing the Quick-Connect Universal CCU settings will help achieve maximum performance from
the system. Difficult lighting is one of the most challenging problems video system integrators face.
The Vaddio CCU will provide the flexibility to fine tune for variables such as cable length, day/night
lighting transitions and lighting color temperature.
Adjust Iris and Digital Gain Settings: Disable Auto Iris. Set the Iris to its largest aperture (lowest ‘f’ number).
Adjust the Gain until the image is too dark and then bring it back until it is properly exposed. Exposures that require
high gain settings will have a grainy video image. Adjust the detail settings for a smoother image.
Adjust Color to Taste: Required adjustments will vary based on the environment. The CCU allows the set-up of
three (3) scenes so settings are available for a variety of conditions. Adjust the Chroma level to taste. Adjust
Red/Blue levels next. Adjusting for skin tones or using a color chart is an easy way to find a good baseline setup.
②①
③④⑤⑥
⑦
All Down
with Power
Cycle for
Defaults

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 16 of 48
C ONTROLLING THE C AMERA
IR Remote Commander
The following functions are accessible with the Vaddio IR remote:
Camera Power On/Off (Toggle on/off same button)
Back Light Compensation (Toggle on/off same button)
Data Screen: Toggle on/off the OSD for the RoboSHOT’s IP/MAC Address
Camera Select (the remote can operate 3 cameras (with 3-IR Freq.)
Pan/Tilt and Home controls with Reverse and Std. Pan direction
Pan/Tilt Reset
Auto Focus (Toggle on/off same button)
Zoom In/Out controls Wide & Telephoto
Fast speed controls (W & T)
Slow speed controls (W & T)
Manual Focus On/Off control (Toggle on/off same button)
Near (-) adjustment
Far (+) adjustment
Six (6) pan/tilt/zoom positioning presets (1 through 6)
Preset Set (store)
Preset Reset (clear)
Red LED that indicates IR Transmission and battery level
The IR Remote operational characteristics are as follows:
Preset Activation: IR Remote is limited to executing Presets 1 through 6
Tri-Sync Speed on Preset: If a global Tri-Sync speed is stored in the preset by the user/admin, then that
speed is used. If no Tri-Sync speed is assigned, then a default (medium) speed will be used.
Preset Store: IR Remote is limited to positional (PTZ) type presets. To set a preset, position the camera,
hold down the Preset Button and touch the one of the preset numbered buttons 1 through 6.
Telnet Control
The following
* Telnet commands are available through the Ethernet Port.
Camera Home
Camera Pan (left, right and speed - real-time operation)
Camera Tilt (up, down and speed - real-time operation)
Camera Zoom (zoom in/out/stop and speed - real-time operation)
Camera Store Preset (Gets or Sets 12 presets with global relative PTZ [Tri-Sync] speed control to destination)
Camera Image (Gets or sets current image control values, sets in 1 of 3 CCU presets)
(AWB or manual w/Red and Blue gain, BLC on/off, Auto Iris or manual with Iris value and Gain, Detail and Chroma)
Camera Sleep (Gets or sets standby power mode - camera has to us less power in this mode)
Exit (ends Telnet session)
Help (displays CLISH syntax)
History (command history)
Network Ping (send ICMP ECHO_REQUEST to network hosts)
Network Settings (Gets MAC address, IP address, Subnet Mask, Gateway and NTP server address)
Network (Gets the current network settings or pings an IP address)
Streaming Mode - USB or IP needs to be changed to USB and IP (get and set streaming modes, on/off)
Streaming Quality (gets/sets high/standard/low for IP)
Streaming Resolution (gets/sets streaming resolution)
Streaming (gets/sets current streaming settings)
System Factory Reset
System Reboot
Version (system version information)
* Please see the full Telnet command list at the end of this manual
Vaddio
IR Remote
Commander

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 17 of 48
T HE S CREEN S HOT T OUR
The RoboSHOT camera platform uses a Linux OS and has a built-in web server. The internal web pages will allow
control of the attached camera via an Ethernet network connection. These web pages will allow the user or
administrator to control the camera, set PTZ presets, set security passwords, change the IP address, view
diagnostics, access the firmware upgrade page and more!
Compatible Web Browsers
You may ask, “What are the approvedweb browsers that work with the RoboSHOT’s embedded web server?” The
answer is: Chrome
®
(latest version), Firefox
®
(latest version), Internet Explorer
®
(versions 8 through 11) and Safari
®
(versions 6 and 7) have been tested thoroughly with RoboSHOT and are compatible.
DHCP IP Set-up (Dynamic Host Configuration Protocol)
DHCP Set-up (skip this section if Static IP). If the LAN has a DHCP (dynamic host configuration protocol) server, then the IP address,
gateway and routing information will automatically be assigned. The software is defaulted to DHCP and will attempt to dynamically obtain an
IP address using DHCP, but it will fall back to the default address of (169.254.1.1) if no DHCP server can be found.
Static IP Set-up:
The static IP can be assigned either through the network or directly to a computer using a cross-over cable. Depending on the age of the
computer, you may not need a cross-over cable. Either way the steps are the same for network or direct connection to a computer. The default
address of the camera is 169.254.1.1 and the Subnet mask is 255.255.0.0. Different computer OS types all have their own way of doing things
(without question), but they are essentially doing the same stuff, changing the IP address so the web pages of the RoboSHOT are accessible
.
Screen Shot: Login
The RoboSHOT webserver is intended as a user’s camera control page at one level, and an administrator’s
management tool at another level, which requires password authentication for access.
The Login Page will appear if there is a user name assigned by the administrator. Assigning a user name can limit
access to the admin menus by a general user.
By default, the User name is: user, and the password for the User account is: password.
The Administrator can set the name and password for the User account.
By default, the Admin user name is: admin, and the password for the admin account is: password
If a user or an admin logs in through this screen, then the next page shown will be the camera control page.
The user will only have access to the camera control page.
The Admin will have complete access to all web pages.

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 18 of 48
Screen Shot: Camera Control Page
This web page provides access to the camera controls for the User and the Admin.
1) Pan, Tilt and Home Controls: These intuitive controls use the up/down and diagonal arrows for camera pan and tilt. The
center button will move the camera to the home position.
2) Zoom Control: The camera’s zoom lens can be controlled with the “+” to zoom-in and the “-“to zoom out.
3) Pan/Tilt and Zoom Speed Controls: The speed for both the Pan/Tilt and Zoom controls can be adjusted with the three
(3) sliders in this section. For tighter shots, it is recommended that the slower speed is used. These controls are for real-
time camera movements only.
4) Standby: The Standby control puts the camera in low power mode and effectively puts the RoboSHOT to sleep. The
camera will pan 90º from center and 30º downward (to not collect dust on the lens). When the camera is inverted (ceiling
mounted) the camera will pan 90º from center and 30º downward. If the system is on, then the button will be blue and
controls will be visible. If the button is red, no controls are accessible and the screen states: Device is in standby. Click
to power-up, then you’ll know what to do.
5) Camera Presets: Twelve (12) camera position presets can be recalled simply by clicking a preset number.
6) Store Preset Button: Clicking the Store button opens up a Store Preset pop-up dialog box. To set presets, set up the
camera shot, click on choice of preset number (1 through 12). The preset is stored and the dialog box closes. The Store
Preset dialog bow will prompt the operator to enter the Tri-Sync speed to the stored camera preset and if the current color
settings are to be stored with the preset too (see the next page).
7) CCU Scenes: The user has access to the CCU scenes set and stored on the Admin pages. There are three (3) user
definable presets and six (6) presets preconfigured by the technical folks at Vaddio (really Scott set them all) that are meant
to be used in certain lighting scenarios. These lighting presets included: Automatic, Incandescent Hi, Incandescent Lo,
Fluorescent Hi, Fluorescent Lo and Outdoor.
8) Administration Menu: By clicking on the Administration menu bar, the Admin Login screen will appear.
➊
➍
➋
➎ ➏
➐
➌
➑

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 19 of 48
Screen Shot: Storing Presets
1) Store Preset: When the Store Preset button is clicked (point 6 on previous page), the Store Preset dialog pops into
existence. To save the current camera shot, click one of the Preset buttons (1 through 12), the button will be
highlighted and the dialog box will present the Tri-Sync controls and if the CCU setting are to be kept with the preset.
2) Save with Tri-Sync and Setting the Tri-Sync Speed: The Tri-Synchronous Motion algorithm in the RoboSHOT
cameras is capable of moving all three (pan, tilt and zoom) axes simultaneously. The algorithm calculates the PTZ
position so pan, tilt and zoom arrive at the preset subject simultaneously. Tri-Sync speed is speed at which all other
presets will use to get to the preset being stored. All axes will launch at the same time and if the next preset position
is not too close or too far, axes should simultaneously arrive at the preset location. Storing the preset with Tri-Sync
is fairly straight forward. Here’s a quick method to set Tri-Sync:
a) Position the first preset, click on Store Preset and click on Preset 1. Check the Save with Tri-Sync box. Move
the tri-Sync speed slider to about the approximate position above (about 1/3 up the speed scale). This is the
speed that all the other presets will use to get to this Preset 1. The speed is stored with the destination preset.
Click on Save to store the camera location and Tri-Sync speed.
b) Set another camera position, and try a different pan, tilt and zoom position and click on Store Preset. Click on
Preset 2 through 12, click on the Save with Tri-Sync box and set the slider to about ½ way this time and click on
Save. These two presets are stored with different preset destination speeds.
c) Click between these two recently stored presets and note the different speeds applied to the 2 presets.
Tri-Sync Notes: If a preset is very close to the previous preset, like within 10º with no change in zoom, it certainly
doesn’t need to be Tri-Sync’d. If a preset is super-fast and off-air, Tri-Sync won’t be of much use either. Tri-Sync
is a cool tool to set for on-air shots, but the process of setting the speeds will need some practice.
3) Store with Current Color Settings: To save the currently assigned CCU scenes settings, check this box.
4) Click Save or Cancel to exit this pop-up dialog box.
➊
➍
➋
➌

RoboSHOT HD Cameras
RoboSHOT HD Cameras - Document Number 342-0797 Rev A Page 20 of 48
Screen Shot: Admin login from the Camera Control Page
On the security page, which will be reviewed at a bit later in the tour, allows the Admin to set the system to allow
automatic guest access to the main camera control page. I f guest access is turned on by the Admin, then system
will open to the camera control page and an additional Admin Login is provided.
The default Admin password is: password.
Admin