TUF-TUG Products TT1-8W User manual

PRODUCTS
WEB-STRAP HOIST/PULLER
TT1-8W
• 1,000 Lb. Lift Capacity
• 2,000 Lb. Pull Capacity
• 8 Foot Reach Capability
• 1 Inch Wide Webbing With
Red Safety Warning Cores
• Double Strength
Dual Drive
• 1/4 Inch Alloy
Hooks
TUF-TUG Products
3434 Encrete Lane, Moraine, Ohio 45439
[phone] • Fax [phone]
TT1-8W 4/15/2020
OPERATING INSTRUCTIONS
TO APPLY TENSION, engage the drive lever
by pushing the black plastic covered spring,
located on the handle, rearward, and
pivoting the handle back and forth.
TO RELEASE TENSION, disengage the
drive lever by pushing the black plastic
covered spring, located on the handle,
forward, pivot the handle forward until
the stop lever is contacted, continue to
apply pressure against the stop lever until
it releases and allow the handle to pivot
backward. Repeat this procedure to release
the load a notch-at-a-time.
TO FREEWHEEL SPOOL, release all of the
line tension, manually disengage the stop
lever by pulling back on the exposed wire
loop and unreel the desired length of cable.
For more information on this product or our other Hoist/Pullers,
Blocks, Pulleys, Fence Installation Accessories or Safety Equipment…
Please Contact:
TUF-TUG Products
3434 Encrete Lane, Moraine, Ohio 45439
[phone] • Fax [phone]

TUF-TUG HOIST/PULLER LIST & PRICES
All prices FOB Dayton, OH and are subject to change without notice.
Part No. ................Description
101-103 ................Frame
101-107 ................Guide
101-108 ................Frame Sleeve
101-109 ................Lever Sleeve
101-110 .................Frame Bolt / Nut
101-111 .................Lever Bolt / Nut
101-113 .................Hook Sleeve
101-114 .................Hook Bolt / Nut
101-116 .................Cover
101-120 ................1/4" Hook
101-201 ................Ratchet Wheel Assm.
101-204 ................Handle Assm.
101-206 ................web & Hook Assm.
101-207 ................Stop Lever Assm.
USE CONSIDERATIONS WITH NYLON WEBBING
HEAT: Nylon webbing is not suited for use in environments above 180˚F.
EXPOSURE: Nylon webbing is adversely affected by prolonged
exposure to extreme ultraviolet light, such as direct sunlight and arc welding.
CHEMICALS: Nylon webbing is not compatible for use in the presence of vapors,
mists, sprays, or liquids of acids, phenolics, or bleaching agents.
Your Tuf-Tug Webbing Hoist/Puller utilizes nylon webbing with red safety
indicating cores inside. These threads are positive indicators that the webbing
has been damaged. If for any reason these red cores are outwardly visible,
discontinue use of the puller. Possible reasons for damaged webbing and
discontinued use include the following:
• Broken or worn stitching at attachments
• Excessive abrasions
• Acid or alkali burns
• Melted or charred sections
• Punctured, cut, or snagged sections
CAUTIONS
• Read and understand all
instructions before using.
• Inspect mechanism and cable/
webbing for proper operation and
condition before each use.
• Know your loadings; do not exceed
rated capabilities.
• This product is intended for
straight-in-line lifting and pulling;
do not side load mechanism or
cable/webbing.
• Do not shock load mechanism or
cable/webbing.
• Always keep a minimum of two
wraps of cable or one wrap
of webbing on the hub while
mechanism is under load.
• Always use puller under manual
power; do not use in place of
tow line.
• This product is not recommended
for use a load binder or tie-down.
• Handle is designed to bend
if overloaded; do not use an
extension bar on the handle.
• Never stand in from of, or in line
with a pretensioned mechanism.
• Do not use to lift people or loads
overhead.
• Do not operate hoist/puller with
twisted, frayed, damaged or kinked
cable/webbing.
• Do not pull cable/webbing over
sharp corners or secure hook back
onto cable.
WARRANTY
“Limited 90 Day Warranty to Original Using Buyer”
All Tuf-Tug Hoist Pullers are warranted for 90 days against defects when
operated under normal conditions, within their rated capacities and in
accordance with the operating instructions and use considerations.
Any part or mechanism that is recognized as defective by Ohio Hoist &
Puller will be repaired Free of Change during the warranted period if it is
returned, prepaid, to the factory with a copy of the sales receipt. Claims
for labor, delays or damages are not covered by this warranty.
This warranty does not apply if the unit has been altered, modified, or
repaired by any source other than Ohio Hoist & Puller. Warranty is also
invalid if the mechanism is subjected to uses or situations warned against
in either the “Cautions Section” or “Use Considerations”.