Turboair TSR-23SD User manual

Turbo air Speeds Up the Pace of Innovation
Refrigerator
Freezer
Installation and Operation Manual
Please read this manual completely before attempting to install or operate this equipment!
CAUTION!
PLEASE KEEP POWER SWITCH ON
BEFORE OPERATING FREEZER
Full Stainless Steel Interior and Exterior
Refrigerator
TSR-23SD
TSR-49SD
TSR-72SD
Freezer
TSF-23SD
TSF-49SD
TSF-72SD

1. SPECIFICATION.......................................................................................... 2
2. SERIAL NUMBER........................................................................................ 2
3. INSTALLATION ............................................................................................ 3
4. CLEANING................................................................................................... 4
5. BASIC OPERATION
5-1. REFRIGERATORS ........................................................................... 5~8
5-2. FREEZERS..................................................................................... 9~12
6. BEFORE REQUESTING SERVICE........................................................... 13
7. WARRANTY......................................................................................... 14~15
2
Turbo air
CONTENTS
PAGE
Refrigerators
SPECIFICATION
MODEL COMP H.P. V/Hz REFRIGERANT AMPS WEIGHT
TSR-23SD 1/3 115V/60Hz R-134a 5.5A 265lbs
TSR-49SD 1/2 115V/60Hz R-134a 9.2A 397lbs
TSR-72SD 1/2 115V/60Hz R-134a 11A 530lbs
The serial number is located on the data label inside.
Please retain the unit’s serial number for service purpose.
SERIAL NUMBER
Freezers
MODEL COMP H.P. V/Hz REFRIGERANT AMPS WEIGHT
TSF-23SD 1/3 115V/60Hz R-404a 7.8A 265lbs
TSF-49SD 3/4 115V/60Hz R-404a 13A 397lbs
TSF-72SD 1 115V/208~220V/60Hz R-404a 10A 540lbs

3
Turbo air
1. GOOD AIR CIRCULATION
- Be sure to avoid any partition and object which may stop the air flow.
- Be sure that air space is allowed to flow the rear of the unit.
Turbo air recommends that the rear of the unit would be no less than 5 inches from the
wall.
2. PLACE ON STRONG GROUND
- Be sure that the location be chosen has a strong enough floor to support the total
weight of the cabinet and any other contents.
3. DO NOT PLACE NEAR HEAT
- Be sure to avoid hot corners and locations near stoves.
- High ambient temperature will make much lower cooling efficiency.
4. INDOOR USAGE ONLY
- Be sure to install this unit indoor.
- So, It should prohibit getting wet from the rain.
5. STABILIZING
- Make sure the unit is installed in a stable condition with the front wheels locked
while in use.
6. LEVELING
- Be sure that the unit levels from the front to the back and side to side.
7. UNIT SHOULD BE ON DEDICATED OUTLET.
INSTALLATION

4
Turbo air
CLEANING
1. CLEANING THE INTERIOR AND EXTERIOR
- The interior and exterior of the unit can be cleaned using warm water with soap.
- Do not use an abrasive cleaner because it will scratch the stainless steel surface.
2. CLEANING THE CONDENSER FINS
- To maintain proper refrigeration performace, the Condenser coil must be free of dust,
dirt, and grease.
This will require periodic cleaning. Condenser fins should be cleaned at least every
three months (90 days) or as needed.
3. CLEAN THE GASKET
- The door gasket should be cleaned frequently to maintain proper sealing.
4. CHECK AFTER CLEANING
- Check the unit again for safety.
- Check that the unit is operating properly.
1. POWER CORD
- Be sure that the power cord is connected to the proper voltage.
- A protected circuit of the correct voltage and amperage must be run for connection of
the line cord.
-Turn ‘off’ the power switch before disconnecting the power cord, whenever
performing maintenance functions or cleaning the refrigerated
cabinet.
- Dual voltage freezer (TSF-72SD) requires receptacle as shown the
right sides.
- Compressor warranties are void if compressor burns out due to low
voltage.
2. RE-STARTING
- If disconnected, wait for 5 minutes before re-starting.
CAUTION
WH
E
BK RD

5
Turbo air
BASIC OPERATION
TSR-23SD
TSR-49SD
TSR-72SD
1. Plug in and turn on the power switch located on the bottom of the top grille right side.
The Display panel will be lighted and make a beep sound. The compressor will begin
to run.
2. The default temperature setting is No. “5”.
3. The compressor is automatically cycled by the electronic controller (PCB, D-Sensor).
4. The Defrost cycle is automatically controlled by the R-sensor, and the PCB.
5. Set level toward “1”for higher temperature and toward “9”for lower temperature.
6. The interior light is activated by the rocker switch at the bottom of the grille when the
door is opened.
7. Evaporator fan motor(s) will run after all doors are completely closed.
REFRIGERATORS

6
Turbo air
DISPLAY PANEL OF REFRIGERATOR
9
TEMPERATURE T.C.
8
7654321
FAN DOOR
TURBO COOLING
TEMPERATURE
˚F
TEMP. SETTING
TURBO COOLING
FAN RUNNING
DOOR OPENING
TURBO COOLING
BUTTON
TEMP. CONTROL BUTTON
(SEE TO PAGE 7)
INNER TEMP.
(SEE TO PAGE 8)
(SEE TO PAGE 7)

7
Turbo air
1. If you push the T.C. (Turbo Cooling) button, the compressor will run continuously until
D-Senser detect 14˚F (-10˚C) to bring down the temperature more quickly.
(max.comp.run time = 120 min.)
2. If you push the T.C. button again during Turbo Cooling mode, the compressor will
return to the normal operation.
3. During the Turbo Cooling mode works, the temperature Up/Down button will not
affect the compressor’s operation.
1. By pushing the up/down button, you can set the inside temperature level from ‘1’to
‘9’.
2. If you want lower temperature, push the Down button to be lighted higher level
numbers.
TURBO COOLING
UP/DOWN BUTTON (Temperature control button)

8
Turbo air
1. It displays the inside temperature.
2. Display range is 14˚F to 69˚F (-10˚C ~ +20˚C).
3. When the inside temperature is lower than 14˚F, the panel will display ‘’.
and, higher than 69˚F, the panel will display ‘’.
1. If the fan motor is running, fan running indicator will be turned on.
2.
Evaporator fan motor is activated when the door (both doors for TSR-49SD, all three
doors for TSR-72SD) is closed.
1. If any door is opened, door opening indicator will be turned on.
2. In case that any door was opened around 30 seconds, warning beep sound will be
ring three (3) times.
3. In case of passing around 1 minute, warning beep sound will be ring again five (5)
times.
4. In case of passing around 5 minutes, the beep sound will be ring continuously.
5. On all the conditions good, the beep sound will stop immediately if the door closed
properly.
INNER TEMPERATURE DISPLAY
FAN RUNNING INDICATOR
DOOR OPENING INDICATOR

9
Turbo air
BASIC OPERATION
TSF-23SD
TSF-49SD
TSF-72SD
1. Plug in and turn on the power switch located on the bottom of the top grille right side.
The Display panel will be lighted and make a beep sound. The compressor will begin
to run.
2. The default temperature setting is No. “5”.
3. The compressor is automatically cycled by the electronic controller (PCB, F-Sensor).
4. The Defrost cycle is automatically controlled by the D-sensor, and the PCB.
5. Set level toward “1”for higher temperatures and toward “9”for lower temperatures.
6. The interior light is activated by the rocker switch at the bottom of the grille when the
door is opened.
7. Evaporator fan motor(s) will run after all doors are completely closed.
8. Good Air Flow in freezer unit is critical.
Be careful to load product so that it neither presses against the back wall, nor reaches
within four inches from the evaporator compartment.
FREEZERS

10
Turbo air
DISPLAY PANEL OF FREEZER
9
TEMPERATURE D.F.
8
7654321
FAN DOOR
MANUAL DEFROST
TEMPERATURE
˚F
TEMP. SETTING
MANUAL DEFROST
FAN RUNNING
DOOR OPENING
MANUAL DEFROST
BUTTON
TEMP. CONTROL BUTTON
(SEE TO PAGE 11)
INNER TEMP.
(SEE TO PAGE 12)
(SEE TO PAGE 11)