turbofan G32M User manual

F24824-15
G32M CONVECTION OVEN
G32MS CONVECTION OVEN
INSTALLATION / OPERATION
MANUAL

MANUFACTURED BY
Moffat Limited
PO Box 10001
Christchurch
New Zealand
Ph: [phone]
Fax: [phone]
WORLD-WIDE BRANCHES
UNITED KINGDOM
Blue Seal
Units 6-7, Mount Street Business Park
Mount Street, Nechells
Birmingham B7 5QU
Ph: [phone]
Fax: [phone]
UNITED STATES
Moffat Inc
3765 Champion Blvd
Winston-Salem
North Carolina 27115
Ph: [phone]
Fax: [phone]
CANADA
Serve Canada
22 Ashwarren Road
Downview
Ontario M3J1Z5
Toll Free:800 263 1455
Ph: [phone]
Fax: [phone]
[email protected]
www.servecanada.com
www.moffat.com
NEW ZEALAND
Christchurch Auckland
Moffat Limited Moffat Limited
PO Box 10-001 4 Waipuna Road
16 Osborne Street Mt Wellington
Christchurch Auckland
Ph: [phone] Ph: [phone]
Fax: [phone] Fax: [phone]
AUSTRALIA
Victoria New South Wales
Moffat Pty Limited Moffat Pty Limited
740 Springvale Road 3/142 James Ruse Drive, Rose Hill
Mulgrave, Melbourne PO Box 913, Smithfield
Victoria 3171 Sydney, N.S.W. 2142
Ph: [phone] Ph: [phone]
Fax: [phone] Fax: [phone]
Western Australia Queensland
Moffat Pty Limited Moffat Pty Limited
67 Howe Street 30 Prosperity Place
Osbourne Park Geebung, Brisbane
WA 6017 Queensland 4034
Ph: [phone] Ph: [phone]
Fax: [phone] Fax [phone]
The reproduction or copying of any part of this manual by any means whatsoever is strictly forbidden unless authorized previously in
writing by the manufacturer.
In line with policy to continually develop and improve its products, Moffat Ltd. reserves the right to change the specifications and
design without prior notice.
© Copyright Moffat Ltd. November 2006.

Date Purchased................................................................. Serial No ..........................................................
Dealer............................................................................................................................................................
Service Agent ................................................................................................................................................
Contents
1
Introduction .......................................................................................................... 2
Installation ............................................................................................................ 3
Before Connection
Supply Requirements
Location
Electrical Connection
Gas Connection
Water Connection
Before Use
Lighting Instructions
Reversing the Door
Specifications....................................................................................................... 7
Operation.............................................................................................................. 8
Description of Controls
Baking
Roast ‘n’ Hold
Oven Racks
Cooking Guide ................................................................................................... 12
Baking
Bake-Off
Roasting
Roast ‘n’ Hold
Cleaning and Maintenance................................................................................ 14
Trouble Shooting ............................................................................................... 15
Spare Parts......................................................................................................... 16
Circuit Schematics............................................................................................. 18
Canada
UK
Non UK / Canada

We are confident that you will be delighted with your TURBOFAN OVEN, and it will become a most valued
appliance in your commercial kitchen.
A new oven can seem very complex and confusing at first glance. To ensure you receive the utmost
benefit from your new Turbofan, there are two important things you can do.
Firstly
Please read the instruction book carefully and follow the directions given. The time taken will be well
spent.
Secondly
If you are unsure of any aspect of the installation, instructions or performance of your oven, contact your
G32 dealer promptly. In many cases a phone call could answer your question.
This oven is designed to meet the technical safety and health standards of the United Kingdom, U.S.A.,
Europe, Canada, Australia and New Zealand.
Instructions to be followed in the event the user smells gas are to be posted in a prominent location. This
information shall be obtained by consulting the local gas supplier.
FOR YOUR SAFETY
DO NOT store or use gasoline or other flammable vapours or liquids in the vicinity of this or
any other appliance.
THIS APPLIANCE IS FOR PROFESSIONAL USE AND IS ONLY TO BE USED
BY QUALIFIED PEOPLE
Improper installation, adjustment, alteration, service or maintenance can cause
property damage, injury or death. Read the installation, operating and maintenance
instructions thoroughly before installing or servicing this equipment.
Introduction
2
CAUTION: When operating the oven the door surface will be hot.

This appliance must be installed in accordance with National installation codes and in addition, in
accordance with relevant National / Local codes covering gas and fire safety.
UNITED KINGDOM: GAS SAFETY (Installation & Use)
REGULATIONS 1984 (Amendment 1990)
AUSTRALIA: AS5601 / AG601 - 2000, Gas Installations Code
NEW ZEALAND: NZS5261, Installation of Burning Appliances and Equipment
UNITED STATES: ANSI 223.1 (Latest edition) National Gas Fuel Code
CANADA: CAN/CGA -B149, Installation Codes for Gas Burning Appliances and
Equipment
Installations must be carried out by authorised persons only. Failure to install equipment to relevant
codes and manufacturers specifications in this section will void warranty.
The oven and its individual shutoff valve must be disconnected from the gas supply piping system
during any pressure testing of that system at test pressures in excess of 3.45 kPa / 34.5 mbar (0.5psi).
This oven must be electrically grounded in accordance with local codes.
Installation must allow for a sufficient flow of fresh air for the combustion air supply. Combustion air
requirements:
Natural Gas (G20-UK) 10m³/hr
Propane Gas (G31-UK) 9m³/hr
Components having adjustments protected (e.g. paint sealed) by manufacturer are only allowed to be
adjusted by an authorised service agent. They are not to be adjusted by the installation person.
Before Connection to Power and Gas Supplies
• Remove all packing.
• Check equipment and parts for damage. Report any damage immediately to the carrier and
distributor.
• Remove protective plastic coating from the side panels.
• Check that the following parts have been supplied with your oven:
4 x Leg assembly
4 x Oven racks
1 x Water inlet elbow (c/w washer)
• Report any deficiencies to the distributor who supplied the oven.
• Fit the legs to the oven or fit oven to manufacturers stand.
• Check that the available power and gas supply is correct to that shown on the rating plate located
on the right -hand side panel.
Supply Requirements
3
Installation
Installation Requirements
It is most important that this oven is installed correctly and that operation is correct
before use.
Installation shall comply with local electrical, gas, health and safety requirements.
Natural Gas LPG Natural Gas - UK Propane - UK
(G20) (G31)
Input Rating 35 MJ/hr 35 MJ/hr 9.5 kW 9.5 kW
(N.H.G.C.) (33,000 Btu/hr) (33,000 Btu/hr) (0.91 m³/hr) (0.67 kg/hr)

Location
• This oven must be installed in an area of adequate air supply. To ensure correct ventilation for the
motor and controls the following minimum installation clearances are to be adhered to:
• This oven must be fitted on supplied legs in all installations, unless installed on a manufacturers
stand.
• Position the oven in its working position.
• Use a spirit level to ensure oven is level from side to side and front to back. (If this is not carried
out, uneven cooking could occur). The legs used with bench/floor mounting or provided with
stands are adjustable and will require adjusting in levelling the unit.
• The unit should be positioned such that the operating panel and oven shelves are easily reachable
for loading and unloading.
• Adequate ventilation is essential. DO NOT obstruct the air flow around the ventilation slots.
Electrical Connection
This oven is fitted with an approved power supply cord via an electrical junction box at the right hand
rear of the unit. Should changing of the cord be necessary then follow the instructions given below:
• Remove right hand side panel to allow access to the terminal block and strain relief cable clamp.
• The cable can be fitted through the small grommet and held by the cable clamp.
Installation
4
Important:
THE VENT LOCATED ON THE OVEN TOP MUST NEVER BE OBSTRUCTED.
Supply Requirements (continued)
Natural Gas LPG Natural Gas - UK Propane - UK
(G20) (G31)
Operating Pressure 0.85 kPa 2.25 kPa 10 mbar 35 mbar
(3.5” w.c.) (9.0” w.c.)
Gas Connection ½” BSP Female ½” BSP Female
½” NPT Female (Canada only)
Electrical Connection 220-240 Volts AC, 50Hz, 0.7A, 0.168kW, Single Phase
220 Volts AC, 60Hz, 0.7A, 0.168kW, Single Phase
110 Volts AC, 60Hz, 2.0A, 0.12kW, Single Phase
Cold Water Connection ¾” B.S.P. (80psi maximum pressure)
Supply Pressure 1.13 kPa 2.75 kPa 20 mbar 37 mbar
(4½” w.c.) (11” w.c.)
Top 200mm / 8” (or 600mm / 24” from a combustible surface)
Rear 75mm / 3”
Left-hand side 75mm / 3”
Right-hand side 75mm / 3” (Fixed installations require at least 500mm (20”) clearance at
the right hand side for service accessibility.)

Gas Connection
• A ½" BSP female elbow (½" N.P.T female - Canada only) is provided at the bottom rear of the
oven.
• A restraint chain anchor has been provided above the gas connection point for fitment of a
restraint chain when a flexible gas line is fitted.
• It is important that adequately sized piping run directly to the connection joint on the oven with as
few tees and elbows as possible to give maximum supply volume.
• A suitable jointing compound which resists the break down action of LPG must be used on every
gas connection.
• Check all connections for leakages.
• Check appliance name plate on oven front right hand for correct orifice size and operating
pressure for the gas being installed, before operation.
• The appliance combination gas valve is fitted with an internal regulator for adjusting the operating
pressure. To access, remove appropriately marked side service panel from bottom right side of
oven. Unscrew and remove regulator cap from gas valve. Adjust regulator to achieve stated
pressure.
NOTE:
Pressure test points are located behind this side service panel also at bottom right side of oven.
Water Connection - Optional (not required for main oven operation)
• If the manual addition of water into the oven for humidification or steaming effect on baked product
is required, the unit’s water connection can be used.
• A cold water supply should be fitted to the water inlet (¾” BSP hose connection) which is located
on the rear of the right hand side of the unit.
• Alternately, a connection elbow and sealing washer is supplied with this unit for direct
connection of a ½” ID hose, and is recommended for easy installation and service.
• Connect water supply - Max inlet pressure 80psi / 550kPa.
• Turn on water supply to check for leaks.
Before Use
• Operate the oven for about 1 hour at 200°C (400°F) to remove any fumes or odours which may be
present.
Lighting Instructions
• Set the thermostat temperature.
• Automatic ignition will light the burner.
• If not, turn the thermostat off, and wait 5 minutes before relighting.
• The burner will cycle on/off to maintain the set temperature.
• Turn the thermostat off to shut-down the burner.
NOTE:
If the burner is not cycling to maintain temperature the ignition system has locked out. To reset turn
the thermostat to the ‘off’ position. Wait 5 minutes before relighting.
If the flame is lost during operation the ignition system will try three times to re-establish the flame with
a 30 second delay between each try, before going into lockout.
Important :
MAXIMUM INLET WATER PRESSURE IS 550 kPa / 80 psi.
Installation
5

Installation
1
2
Reversing the Door
If desired, a left hand hinged oven door can be changed to a right hand hinged door (or vice versa).
• While supporting the door, undo the door hinges from the oven. Remove the door.
• The bottom right door catch plate should now be transferred to the top left of the oven (1), and the
top right door catch plate transferred to the bottom left of the oven (2).
• Secure the door hinges and oven door to the right hand side of the oven door opening.
• If alignment of the door is necessary, the five screws along the bottom of the oven can be
loosened, and the door moved a small amount to ensure that it is square with the oven. Tighten
the screws when the correct door position is attained.
• If necessary the roller catches can be removed from the door (after removing handle on stainless
steel doors) to adjust height settings for correction of door catch operation.
Important :
THE FOLLOWING PROCEDURE SHOULD ONLY BE PERFORMED BY A QUALIFIED
SERVICEPERSON.
6

7
Specifications
Side
Front
205
GAS
70
50
710
MWS
1E
510
E
1MWS
350
900
810
E
1
MWS
GAS
GAS
(28")
28"
(28") (32")
(2¾")
(3½")
(35½")
(20")
(13¾")
(8")
(2")
Natural Gas LPG Natural Gas - UK Propane - UK
(G20) (G31)
Input Rating 35 MJ/hr 35 MJ/hr 9.5 kW 9.5 kW
(N.H.G.C.) (33,000 Btu/hr) (33,000 Btu/hr) (0.91 m³/hr) (0.67 kg/hr)
Injector Size Ø2.80 mm Ø1.80 mm Ø2.60 mm Ø1.55 mm
Supply Pressure 1.13 kPa 2.75 kPa 20 mbar 37 mbar
(4½” w.c.) (11” w.c.)
Operating Pressure 0.85 kPa 2.25 kPa 10 mbar 35 mbar
(3.5” w.c.) (9.0” w.c.)
Gas Connection ½” BSP Female ½” BSP Female
½” NPT Female (Canada only)
Electrical Connection 220-240 Volts AC, 50Hz, 0.7A, 0.168kW, Single Phase
220 Volts AC, 60Hz, 0.7A, 0.168kW, Single Phase
110 Volts AC, 60Hz, 2.0A, 0.12kW, Single Phase
Cold Water Connection ¾” B.S.P. (550kPa / 80psi maximum pressure)
Plan

Operation Guide
8
Operation
Power
Depress to switch power on or off (switch
illuminates when power is on).
Thermostat
Temperature range 50-320°C (120 - 600°F).
Indicator illuminates when the burner is cycling ON
to maintain set temperature.
Bake Timer
1 Hour bake timer.
(Indicator illuminates when “time up” (0) reached,
and buzzer sounds).
Roast ‘n’ Hold
Depress switch to activate ’Roast ’n’ Hold’ function.
(Switch illuminates when ON).
Roast Timer
3 Hour roast timer.
(Indicator illuminates when “time up” (0) reached).
Product is held at 75°C (165°F).
Steam Switch
Push switch to activate water injection. (Water
injects into oven while button is depressed).
Light Switch
Push switch to activate lights.
(Lights illuminate while button is latched in the
down position).
Description of Controls
Important :
Ensure that a clearance of 50mm (2”) from the oven ceiling is maintained when placing product on the
top shelf. This ensures correct operation of the oven.

9
Operation
Baking
1. Turn power on
Power switch illuminates when it is depressed and latched in the down position.
2. Set thermostat to desired temperature
The heating indicator light will illuminate whenever the burner is cycling on to maintain the set
temperature.
Note:
If the burner is not cycling to maintain temperature the ignition system has locked out. To
reset turn the thermostat to the ‘off’ position.
If the flame is lost during operation the ignition system will try three times to re-establish the
flame with a 30 second delay between each try, before going into lockout.
3. Load oven
Once the oven is up the temperature, open the door and load the oven with product. Avoid
delays in loading the oven with the door open as this will delay the oven’s temperature
recovery.
Note:
The oven lights will illuminate when the door is opened.
4. Set bake timer to desired time
To set timer, turn knob clockwise to the required time. At any stage, the time can be adjusted
in either direction.
For settings less than 10 minutes, first set to greater setting, then turn down to the required
time period.
Note:
This 60 minute timer is completely independent of the oven control.
5. Water injection
To steam the oven while baking, push the steam switch on the control panel. We
recommend a 2-15 second injection period, according to product need, for this oven.
Keep switch depressed for required steam period.
6. Light
To view the product while baking, depress the light switch on the control panel. The lights will
stay on while the switch is latched in the down position.
7. Time up.
When the timer reaches 0 minutes the buzzer sounds and indicator illuminates.
To cancel the buzzer turn the timer to the off position.
8. Unload oven
Open the door and unload the oven .
Note:
The oven lights will illuminate when the door is opened.

Operation
10
Roast ‘n’ Hold
1. Turn power on
Power switch illuminates when it is depressed and latched in the down position.
2. Set thermostat to desired temperature
The heating indicator light will illuminate whenever the burner is cycling on to maintain the set
temperature.
Note:
If the burner is not cycling to maintain temperature the ignition system has locked out. To
reset turn the thermostat to the ‘off’ position.
If the flame is lost during operation the ignition system will try three times to re-establish the
flame with a 30 second delay between each try, before going into lockout.
3. Load oven
Once the oven is up the temperature, open the door and load the oven with product. Avoid
delays in loading the oven with the door open as this will delay oven temperature recovery.
Note:
The oven lights will illuminate when the door is opened.
4. Set roast timer to desired time
This 3 hour timer is electrically driven and is set by turning the timer knob in either direction to
the required time. The timer can be set when convenient, but will not start working until the
oven control is set and the Roast ’n Hold switch is depressed (switch illuminated).
5. Depress roast switch
Depress the Roast ’n Hold switch. The switch will illuminate and the timer will begin to count
down.
6. Water injection
To steam the oven while roasting, push the steam switch on the control panel. We
recommend a 2-15 second injection period, according to product need, for this oven.
Keep switch depressed for required steam period.
7. Light
To view the product while roasting, depress the light switch on the control panel. The lights
will stay on while the switch is latched in the down position.
8. Hold
When the timer reaches the hold position, the main oven thermostat is turned off and a
pre-set hold thermostat located behind the control panel will control the oven to keep the food
warm at serving temperature as long as required until the Roast ‘n Hold switch is turned off.
Note:
The hold light will illuminate when the timer reaches hold until the Roast ’n Hold switch is
turned off. The hold light may come on briefly when the Roast ’n Hold control is first switched
on until the oven heats up beyond the pre-set holding temperature.

11
Operation
Oven Racks
The oven is supplied with four general purpose oven racks. These racks incorporate two important
safety features:
• Self Supporting: When fitted, the oven racks are self supporting and will not drop or angle down
when the racks are withdrawn during operation, when loading and unloading products on racks or
when attending to the product being cooked during it’s cook cycle.
• Auto Supporting: The oven rack supports incorporate a special retaining tab which provides a
positive stop to each oven rack and stops it’s inadvertent removal during normal operation.
To fit the oven racks follow the steps shown in the diagram below.
To remove oven racks reverse the procedure.
1
2
3
4
5
1. Fit the oven rack, positioning the rack back stop on top of the rack runner.
2. Slide the rack along the runner and ensure that the front stop is under the rack runner.
3. Slide the rack to the rear of the oven.
4. Allow the rack back stop to drop below the rack runner.
5. The rack can now be pulled forward and loaded as required.
NOTE: Components having adjustments protected (e.g. paint sealed) by manufacturer are only to be
adjusted by an authorised service agent. They are not to be adjusted by the user.

This TURBOFAN oven will cook a greater quantity of food faster, at a lower temperature and more evenly
than an ordinary oven. As many excellent recipe books are published, it is not our intention to list recipes,
but to provide a temperature and time chart as a guide.
Baking
Select a temperature of about 20-30°C (35-55°F) lower than in a conventional oven and preheat oven
until the heating indicator light goes out. The oven has now reached the desired temperature and
trays of food may be placed in the oven. The oven will take four American trays (26" x 18") or eight
American half trays (18" x 13").
Use the racks supplied if American baking trays are not available.
FOOD TEMP°C TIME
Sponges 165 10-12 mins
Small Cakes 165 8-12 mins
Butter Cakes 160 35 mins
Fruit Loaf 150 40-50 mins
Macaroons 160 15-20 mins
Biscuits 140 12-20 mins
Shortbread 130 15-20 mins
Scones 200 10-12 mins
Madeira 165 35-50 mins
Bread 200 25-35 mins
Plain Fruit Cake 165 1-1½ hrs
Rich Fruit Cake 130 2-3 hrs
Gingerbread 140 35-50 mins
Baked Custard 130 50 mins
Souffle 165 25 mins
Rice Pudding 130 2-3 hrs
Pastry
Puff 220 8-12 mins
Short 175 8-12 mins
Flakey 205 8-12 mins
Jam 185 12-20 mins
Fruit 185 35 mins
12
Cooking guide
Bake-Off
Frozen product (yeast, breads or butter based pastries) is placed on baking trays and put into a
refrigerator overnight to thaw. After proofing, the trays of breads or pastries are baked in this oven.
Oven temperature for yeast based products should be 190-220°C (340-355°F).
Oven temperature for butter based products should be 180°C (320-330°F).
A full load will bake in 20-25 minutes.

Roasting
Set the oven temperature to 150-160°C (300-320°F). The hot air circulating in the oven reduces
moisture loss and shrinkage. Roasting times are reduced by approximately 20 minutes per kg.
MEAT TIME per kg
Beef - Rare 30-40 min
Beef - Medium 40-50 min
Beef - Well Done 50-60 min
Veal 50-70 min
Lamb 30-40 min
Duck 50 min
Goose 50 min
Turkey 30-40 min
Chicken
- under 1kg
- over 1kg
50-65 min
40-50 min
Roast-’n’-Hold
This system will automatically cook food for a set time, then hold the oven at a preset temperature
indefinitely to maintain food at a serving temperature after cooking has been completed.
When the oven has reached the set temperature, place food in the oven, set roast cooking time and
depress the Roast ’n’ Hold button. The hold indicator will come on when cooking is complete.
To return to normal operation, push the Roast ‘n’ Hold switch again (switch will cease illuminating).
Cooking guide
13

Exterior
Clean with a good quality stainless steel cleaning compound. Harsh abrasive cleaners may damage
the surface.
Interior
Ensure that the oven chamber is cool. Do not use wire brushes, steel wool or other abrasive materials.
Clean the oven regularly with a good quality oven cleaner. Take care not to damage the fan or the
tube at the right side of the oven which controls the thermostat.
Oven Racks
To remove, follow instructions given in operation section.
Side Racks
To remove, lift front top to disengage and slide rack forward. To replace, slide top rear slot in rack
onto rear stud, then engage front keyhole on front stud.
Lamp Glass
To remove glasses, unscrew anti-clockwise. To replace, screw in clockwise, but do not over tighten.
Ensure that the silk gasket is fitted before replacing the lamp glass.
Oven Seals
To remove, hold at their centre point and pull forward until they unclip. Remove side seals first, then
top and bottom. The seals may be washed in the sink, but take care not to cut or damage them.
To replace, have the lip facing the oven opening. Fit the top and bottom seals first, then the side
seals.
Oven Door Glass
Clean with conventional glass cleaners.
Venting
Regularly check that the oven flue tube is free of obstruction. The flue tube must NEVER be covered.
Lubrication
No lubrication is required by the user. Components are self-lubricating. It is recommended, however,
that a light coating of grease be used on the door catches to provide smooth operation.
14
Cleaning
Caution:
ALWAYS TURN OFF THE POWER SUPPLY BEFORE CLEANING.
THIS UNIT IS NOT WATER PROOF.
DO NOT USE WATER JET SPRAY TO CLEAN INTERIOR OR EXTERIOR OF THIS UNIT.
Cleaning Guidelines

15
Trouble-shooting
Fault Possible Cause Remedy
The oven does not operate / start. The mains isolating switch on the
wall, circuit breaker or fuses are
“off” at the power board.
The power switch on the oven is
off.
Turn on.
Depress switch. Switch will
illuminate.
Burner will not ignite. Isolating valve on oven is turned
off.
No gas supply to unit.
Turn on.
Check gas supply.
Bake timer does not time down. Bake timer not set correctly. For settings less than 10 minutes,
first set to greater setting then
turn back to desired setting.
Roast timer does not time down Roast ‘n’ Hold button not
depressed.
Depress Roast ‘n’ Hold button.
(Roast timer only operates when
Roast function is selected).
Oven light not illuminating. Blown bulb. Replace bulb.
No water injection / steam. Water not turned on. Turn water on at water supply.
NOTE: Components having adjustments protected (e.g. paint sealed) by manufacturer are only allowed
to be adjusted by an authorised service agent. They are not to be adjusted by an unauthorised
service person.

Replacement Part List
Controls
021473 Power Switch (220-240V)
021514 Power Switch (110V)
024774 Thermostat
020823 Knob - Thermostat / Bake Timer
020849 Neon Indicator (220-240V)
023857 Neon Indicator (110V)
011760 Bake Timer
011794 Buzzer (220-240V)
015822 Buzzer (110V)
021476 Roast ‘n Hold Switch (220-240V)
021515 Roast ‘n Hold Switch (110V)
011419 Roast ‘n Hold Timer (220-240V, 50Hz)
011983 Roast ‘n Hold Timer (220-240V, 60Hz)
015823 Roast ‘n Hold Timer (110V, 60Hz)
021472 Roast ‘n Hold Timer Knob
021534 Roast ‘n Hold Relay (220-240V)
021535 Roast ‘n Hold Relay (110V)
021474 Steam Switch
024773 Light Switch
018223 Hold Thermostat
024802 Microswitch
003002 Oven Lamp Glass
003434 Silk Gasket
013520 Oven Lamp Assembly - 40W Miniature Edison Screw (220-240V)
023216 Oven Lamp Assembly - 40W Edison Screw (110V)
013521 Oven Light Bulb (220-240V)
---------- Oven Light Bulb (110V) - E26 40W
019369K Over-temp Thermostat Kit (UK Only)
Motor
014672 Fan Motor (220-240V)
015821 Fan Motor (110V)
015598 Oven Fan
Steam System
020851 Water Solenoid (240V)
021617 Water Solenoid (110V)
021057 Spray Nozzle Assembly
021526 Water Inlet Elbow
021527 Washer
Ignition System
023025 Ignition Box (220-240V - SIT)
023024 Ignition Box (110V, USA/Canada - Fenwall)
019370 Gas Control Valve (220-240V)
015626 Gas Control Valve (25V)
024851 Transformer (USA/Canada)
SA1530 Complete Ignition Electrode Assembly
025071 Flame Sensor Electrode
024127 Spark / Earth Electrodes
Spare parts
16

Door
024784 Door Seal (Side)
024785 Door Seal (Top/Bottom)
020082 Top Hinge
020083 Bottom Hinge
024809 Roller Catch
017905 Door Bush
021468 Door Handle (G32M)
024599 Door Handle Bracket (G32M)
024844 Door Outer Glass (G32M)
002340 Door Inner Glass (G32M)
024713 Door Handle (G32MS)
023063 Door Glass (G32MS)
Racks
015575 Oven Side Rack - LH
015656 Fan Baffle
015168 Oven Rack
Gas Type Conversion Kits
025901 Natural Gas and LPG Conversion Kit
019379 Natural Gas to Propane Gas Conversion Kit (UK Only)
019378 Propane Gas to Natural Gas Conversion Kit (UK Only)
Stacking Kit
025739 Double Stacking Kit
Spare parts
17

Circuit schematics
18
Circuit Schematic - Canada Only
V2 S1
GND
YELLOW
BLUE
TH
V1
BLACK
WHITE
SPARK
LIGHTS
TIME
UP
13
4
LIGHTSWATER
2
1
3
NC
M'SWITCH
DOOR
C
T'STAT
4
5
M
2
1
3Hr TIMER
HEATING
6 3
135
7
HOLD
4
HOLD
42 8
62
HOLD
3
1
2
THERMOSTAT
HOLD
12
1
43
21
IGNITION
BOX
2 1
2 1
NO
1Hr TIMER
GAS SOLENOIDS
1/2" NPT MALE
10mm ID HOSE
GAS
(3/8 inch)
WATER
GAS REGULATOR
CONNECTIONS
EARTH/GROUND
ELECTRICAL
(GREEN/YELLOW)
(RED)
(BLACK)
NEUTRAL
BUZZER
B
POWER
WATER
TRANSFORMER
SENSOR
WATER SOLENOID
INJECTOR