Turin Networks CMG Router User manual

CMG Router
QUICK START GUIDE
Part Number: 002-0142-0230
Product Release: 2.91
November 2008

Copyright 2008 Turin Networks Inc. All rights reserved.
The information presented in this manual is subject to change without notice and does not represent a
commitment on the part of Turin Networks Inc. The hardware and software described herein are furnished
under a license or non-disclosure agreement. The hardware, software, and manual may be used or copied only
in accordance with the terms of this agreement. It is against the law to reproduce, transmit, transcribe, store
in a retrieval system, or translate into any medium - electronic, mechanical, magnetic, optical, chemical,
manual, or otherwise - any part of this manual or software supplied with the CMG Service card for any
purpose other than the purchaser’s personal use without the express written permission of Turin Networks
Inc.
Adit and the Turin Networks logo are registered trademarks of Turin Networks Inc. All other brand or product
names are trademarks or registration trademarks of their respective companies or organizations.
Supporting Software Versions:
Adit 600 Controller Release 9.7.1
CMG Router Release 2.91
Corporate Contact Information:
Turin Networks, Inc.
1415 North McDowell Blvd.
Petaluma, CA 94954
Phone: [phone]
Fax: [phone]
www.TurinNetworks.com
Turin Technical Assistance Center:
E-mail: [e-mail]
Phone (US): 1-800-887-4638
Phone (International/Direct): 1-707-665-4355

QUICK START GUIDE
In this Guide
Installation
Basic Setup
Basic VoIP Setup
Fax and Modem Setup
PPP Internet Connection and Public IP Address
Routing
Frame Relay Internet Connection and Public IP
Address Routing
Back-to-Back with PPP
Back-to-Back with Multi-Link PPP
Back-to-Back with Frame Relay

4 CMG Router - Release 2.91
Quick Start Guide
Installation
Installation
Installation of the CMG Router card into the Adit 600 chassis.
zUnit can be on or off
zCMG Router card will work in any slot
zSlide card into slot until fully seated
zCMG Router has completed its boot cycle when CRD light is solid
The following setups are all executed with CLI
NOTE: Configuration can be done with the following CLI commands or
with the Router Menu-Driven Software.
Basic Setup
Command Description
set {ds0-addr} type data Confirm DS0 is set to type data.
ds0-addr = {slot:port:channel} of DS0
Example: set a:1:1-24 type data
connect {slot:port:trunk}
{slot:port:channel}
Cross-connect T1 to router card.
Example: connect a:1:1-24 6:1:1 (router in slot 6)
set {router-addr} proxy
{disable|enable}
Disable/enable router proxy.
router-addr = {slot:port}| of router card.
Example: set 6:1 disable.
set {slot:port} up Set Router LAN as In-Service. Example: set 6:1 up
telnet {router_card-addr} Telnet to Router card.
router_card-addr = {slot} location of router card
Example: telnet 6 (if earlier than 3.0 release {slot:port} must
be used)
Local and Remote Profile Setup
reinitialize To enable any configuration changes, the card must be
reinitialized.

CMG Router - Release 2.91 5
Quick Start Guide
Basic VoIP Setup
Basic VoIP Setup
This example is with an Adit 600 with the following cards installed:
zController Card (4.0 or higher)
zCMG Router Card, 1.0 or higher (example - slot 6)
z3 FXS Cards, 1.03 or higher (example - slots 1, 2 and 3). Cards are configured for
Loop Start POTS lines.
Overview
zAdit 600: the DS0s supporting the bundled service delivery will be cross-
connected to the CMG card
zAdit 600: the CMG voice channels are connected to the FXS channels
zAdit 600 CMG: the VoIP parameters and data parameters are configured
zAdit 600 uses endpoint prefix "aaln" and endpoint suffix "1-48" i.e. channel 1
would be suffix "1", channel 5 would be suffix "5"
Adit 600 Implementation in VoIP Application

6 CMG Router - Release 2.91
Quick Start Guide
Basic VoIP Setup
Command Description
set local off Set the controller to use CLI commands
disconnect a:1 Disconnect all connections to the T1-1 on the
Controller (slot a)
disconnect 1 Disconnect all connections to the FXS card in slot 1
disconnect 2 Disconnect all connections to the FXS card in slot 2
disconnect 3 Disconnect all connections to the FXS card in slot 3
disconnect 6 Disconnect all connections to the router card in slot 6
set a:1 up Set the T1 on the controller up
set a:1 fdl none Disable FDL output messages on the DS1
set a:1 lbo 1 Set the DS1 Line Build Out to 0-133 feet
set a:1 framing esf Set the DS1 to Extended Superframe (ESF) framing
set a:1 id "TUR DS1# A:1" Set the DS1 ID to "TUR DS1# A:1"
set a:1 linecode b8zs Set the DS1 line coding to B8ZS.
set a:1 loopdetect on Enable the detection of CSU loop code on the DS1
set a:1:all type data Set the T1-1 of the Controller, Type to Data
set a:2 down Set the T1-2 as Out-of-Service
set clock1 a:1 Set primary master transmit clock source
set clock2 internal Set secondary clock source
set a:2 up Set the T1-2 as In-Service
connect a:1:1-24 6:1:1 Connect Data DS0s to the CMG card
connect 6:1:1:1-8 1:1-8 Connect CMG voice ports to FXS ports
connect 6:1:1:9-16 2:1-8 Connect CMG voice ports to FXS ports
connect 6:1:1:17-24 3:1-8 Connect CMG voice ports to FXS ports
set verification off Disable verification prompts

CMG Router - Release 2.91 7
Quick Start Guide
Basic VoIP Setup
set 6:1:1 encapsulation ppp Set Router trunk encapsulations to Point-to-Point
Protocol.
set 6:1:1 up Set Router trunk as In-Service
set 6:1 ip address {ip-addr}
{mask}
Set Router IP Address and Subnet Mask
set 6:1 up Set Router as In-Service
add 6 "RemoteAdit" static ip
network {ip-addr} {mask}
{next-hop-ip-addr} 1
Set router WAN static ip network. Metric set as 1,
normally indicates a direct network
set 6 "RemoteAdit" trunk 1 Set router WAN trunk to port 1
set 6 "RemoteAdit" up Set router WAN as In-Service
set 6 log last detail Set the router log to add new entries and display the
log in detail
set 6 voip sdpaddress 11.168.1.1 Set the address value to be used for the origin
and connection lines in the SDP. (May be required
depending on how the LAN and WAN are
configured.)
reset Reset the CMG card, to apply all configurations
Command Description

8 CMG Router - Release 2.91
Quick Start Guide
Fax and Modem Setup
Fax and Modem Setup
To configure the fax and modem bypass, the following is required.
zAdit 600, release 8.0
zCMG Router, release 2.3 with G.729 feature enabled (software keyed)
zCMG Router User Interface to configure, CLI configuration not available until
Adit 600 9.0
The following will configure the Fax and Modem
1. Telnet into the Router
> telnet 4
Connected.
Escape character is '^]'.
Attempting Turin Networks CMG connection...
CMG [Wed Jan 2, 2002 0:05:05] (<CR> to login)
Password >******
Select a terminal type...
(<space> or <back-space> to toggle, <CR> to accept)
Terminal: <VT100>

CMG Router - Release 2.91 9
Quick Start Guide
Fax and Modem Setup
2. Select Configuration: <Profile Directory> from the Main Menu, and select
[ENTER].
3. Select Router CARD <Setup -> and select [ENTER].
Main
Menu
Profile
Directory
Window

10 CMG Router - Release 2.91
Quick Start Guide
Fax and Modem Setup
4. Select VOIP Configure -> and select [ENTER].