TUYA S9E User manual

10”Super Smart Multi-functional Control
Panel(in-wall) SPEC
Ver.
Description
Creator
Date
V1.2
First edition
Engineer Department
June-13-2023

Contents
Chapter 1 Product presentations........................................................3
1.1 Appearance.................................................................................3
1.2 Main Features.............................................................................3
Chapter 2 Product Specifications....................................................... 4
RK3566B Quad core Cortex-A35............................................4-5
Chapter 3 Ports and Specifications....................................................5
3.1 Interface and ports.............................................................. 5-6
3.2 Specifications............................................................................. 7
Chapter 4 Installation instructions.....................................................8
4.1 Installation drawings........................................................... 8-9
4.2 Wires connection drawing.................................................. 10
Chapter 5 Operation guideline......................................................... 11
5.1 Safety Notes*****....................................................................11
5.2 Operation guideline........................................................11-19

Chapter 1 Product presentation
1.1 Appearance
1.2 Main Features
●Fit Asian 86mm*86mm wall boxes, simple inwall installation.
● 10.1-inch HD LCD, IPS, multi touch screen, quadruple
microphone with noise reduction, built in 2 x 2W speakers,
light sensor, radar sensor, temperature and humidity sensor.
● ZigBee gateway function, APP remote control.
● Control the lights, curtains, air conditioners, and all other
Smart Home devices. Configure smart home scenes in the
APP, turn on the scene mode with one touch on the screen.

Chapter 2 Product Specifications
Specification
CPU
RK3566B Quad core
Cortex-A35
OS
Android 11
RAM
2GB
Screen
10.1 Inch (1920*1200)
G+FF Crafted Multi Touch
Anti-fingerprint Coating
ROM
16GB
Bluetooth
BLE 5.0 Single point
Ethernet
10M/100M Adaptive
Ethernet RJ45
Material
PC
WiFi
5G/2.4G
(IEEE802.11b/g/n)
Zigbee
802.15.4 PHY/MAC
Zigbee network protocol
stack (Zigbee 3.0)
Temperature
Measurement range of
temperature:
0%-99%RH
Humidity
Measurement range of
humidity : 0℃ to +60℃
Ports
USB Type-C port,
RJ 45
Built-in
Sensors
Temperature
and humidity sensor, light
sensor, radar sensor
Functions
Gateway
Built-in Tuya Zigbee and support custom zigbee.

Relays
Built in 2 relays (200W Each) which can control 2 switches of the
room lights locally.
Music play
Built in 2*2W Mono speakers, users can custom their local
music source play, online music sources optional.
Light sensor
Automatically adjust the screen brightness according to
surroundings.
One Smart Control Panel could control all your smart switches, smart
sockets, lights, air conditioners, curtains, clothes hangers, security
cameras, smart sensors,up to 100+ ZigBee sub devices.
Chapter 3 Ports and Specifications
3.1 Interface and ports

3.2 Specifications
Item
Specifications
Product
Name
Super Smart Multi-functional Control Panel
Product
Model
S9E
Input Power
100-240VAC, 0.3A, 50/60Hz
Working
Temperature
0℃ to +40℃
Working
Humidity
5% to 90%RH(Non-condensing)
Wireless
Protocol
Wi-Fi, Bluetooth, Zigbee
Product
dimensions
272x155x38mm (with the base)
272x155x11.5mm (without the base | Outside the wall)
68x68x26.25mm (back base dimension)
60mm (bolt hole spacing)
Net weight
About 961g

Chapter 4 Installation instructions
● Turn off the main power in the electricity box and confirm the live wire is
not alive with a test pencil.
● Remove the base of the smart panel and install it in the wall box (as
shown in the pictures following).
● Check the wires and make sure the wires are in good contact with the
terminals and no exposed cooper wires.
● Fasten the base to the wall box with mounting screws and fix the smart
panel back to the base.
● Note that the screws should not be fixed too tight during installation in
case any deformation or damage to the screen and hardware.
● If your smart panel is not flat after installation, do not press the screen
violently, please check the wall box and the base installation at first.
4.1 Installation drawings

Note: Make sure the circuit power were cut off before wire
connections!
Circuit breaker used as disconnected device shall be
incorporated in the electrical installation of the building.
Depth of the wall box should be more than 50mm.

4.2 Wires connection drawing

Chapter 5 Operation guideline
5.1 Safety Notes*****
●This product must be installed by professional electricians.
● Turn off the main power in the electricity box and confirm the live wire is
not alive with a test pencil.
● This product should be kept away from fire and water during installation
and use.
● This product can not be used in moisture circumstances such as
bathroom.
● Please note that this product doesn’t support PoE, please do not plug
the PoE network cable into ethernet port to avoid burning damage.
5.2 Operation guideline
*This operation guideline is based on Tuya ZigBee, Tuya
App,Tuya cloud platform and Smatek S9E firmware. If
any other platforms or firmware, please follow their
operation guidelines.
(1)The product will be turned on once you connect it to the
power supply. The product will get to the network settings

when you start it in the first time. You can also get into the
network settings from the select menu by dropping down
from the top of the LCD screen.
(2)There are two options in the network settings. You can
select wireless connection or wired connection. There will be a

QR code showing on the screen after the network connection
is done.
(3) Start the Tuya App in your smart phone, select the “ ”
at top right corner in the App home page, and then select the
“ ”at top right corner in the App page.

(4)Scan the QR code on the screen of the product to add it into
the Tuya App. You will find a 10'' panel icon in your App.
(5) Enter the panel interface in the Tuya App, you will see the
gateway and switch icons like and . Click the
switch icon to control 2 local switches (load of each switch for
lamps should be no more than 200W.). It means the switch is
off when the icon is in grey, and the switch is on when it is in
orange.

Long press switch 1 or switch 2 to change the name of the
switch.
(6) Click the gateway icon to add ZigBee sub devices.
Make sure the ZigBee sub devices are in the set-up mode.
The gateway will search and add the sub devices
automatically. You can follow the user manual of the sub
devices to make sure it is in set-up mode. (Usually it is long
press the power button or the reset button in 5s, then the
LED indication light flickering which means it is in the
set-up mode.)
You will see the following pictures in the Tuya App when
you are adding sub devices to the gateway. Make sure the
sub devices are in the set-up mode and the LED indication
light is flickering.

(7) Click the Done button on the App after you add the sub
device successfully. For example (3 Gang Switch) as the
following.
(8) You could change the name of the sub devices after they
are added to the gateway successfully.

Drop down - sync to have devices and scenes sync to panel.
(9) You could change the device type by getting into the
device interface in the App. It means the switch is off when it is
in grey, and the switch is on when it is in green. You could also
set up timers(Schedule) for the switches to realize the
automation control.

(10) If you want to add your devices faster,click the“ ”
and then select the “ ”to add corresponding devices
manually,finally drop down the list on panel and click
“sync” to stay sync with App.

If there is any questions when you add some other sub
devices, please contact us for support.