TV Bedstore MONACO User manual

2Hrs
Page 1 of 21
MONACO OTTOMAN TV BED
ASSEMBLY INSTRUCTIONS
If Media Tray is wanted on
the left side, fit side rail (3)
to left and (4) to right.
If Media Tray is wanted on
the right side, fit side rail (4)
to left and (3) to right.
(4)
(3) (4)
(3)
V1 210424
An instructional video of the Operation of the Ottoman Lift Up system is available via YouTube using
the
following address: https://youtu.be/hyq4zm7h_yU
BT OPT
MODE
MIN
OFF/- +/ON
+
VOL.
BASS
TREB.
L
TORCH
MAX
BASS.
ADJUST BASS ATTENUATION - THESE BUTTONS INCREASE or
DECREASE THE LOWER FREQUENCIES OF THE SOUND.
TREBLE.
THESE BUTTONS INCREASE or DECREASE THE HIGHER FREQUENCIES
OF THE SOUND UNTIL THE PREFERRED SOUND EFFECT IS ACHIEVED.
NOTE: IF YOU REDUCE LEVEL OF THE HIGHER FREQUENCIES THE
VOLUME OF THE SOUND SEEMS TO BE REDUCED - THIS IS NORMAL.
MIN
OFF/-VOL. +/ON
MAX
MIN MAX
OFF/-VOL. +/ON
BASS +
+
TREB. +
R
LR
LH - PLATFORM LED LIGHT --- RH - UNDERBED LED LIGHT (IF FITTED).
TV LIFT UP - TV WILL WORK NORMALLY
TV LIFT STOP
TV LIFT DOWN - TV WILL SWITCH OFF FOR SAFETY
NOTE: BLUETOOTH WILL WORK NORMALLY WHEN TV IS UP OR DOWN.
SYSTEM ON / OFF.
1) PRESS ON BUTTON FOR 3 SECONDS TO START UP THE SYSTEM. RED
LIGHT ON SOUNDBAR IS LIT AND SYSTEM VOICE WILL TELL YOU
POWER IS ON, YOU CAN THEN OPERATE THE CONTROLS.
PRESS OFF BUTTON FOR 3 SECONDS TO CLOSE DOWN THE SYSTEM.
AUDIO VOLUME.
ONCE SYSTEM IS ON, USE --- + or - --- BUTTON TO INCREASE or
DECREASE THE VOLUME -- NOTE THIS CONTROL OPERATES STEP BY
STEP IN EACH DIRECTION - PRESS / RELEASE / PRESS / RELEASE ETC.
IT IS BETTER IF THE VOLUME IS REDUCED PRIOR TO SWITCHING OFF
THE SYSTEM.
STEREO BALANCE.
PRESS LEFT BUTTON FOR SOUND TO COME MORE FROM SPEAKERS ON
LEFT SIDE. PRESS RIGHT BUTTON FOR SOUND TO COME MORE FROM
SPEAKERS ON RIGHT SIDE.
CENTRAL BUTTON IS TO RESET BACK TO NORMAL STEREO SOUND.
BT OPT
MODE
MODE SELECTOR - BT or OPT (BLUETOOTH or OPTICAL).
SYSTEM WILL ALWAYS START CONNECTED TO TV BY THE OPTICAL
CABLE SO YOUR OWN TV MUST HAVE AN OPTICAL PORT.
TOGGLE TO BT MODE, BLUE LIGHT ON SOUNDBAR LIGHTS UP. SYSTEM
VOICE WILL ANNOUNCE --- 'PAIRED' --- IF CONNECTED TO SAME DEVICE
PREVIOUSLY or IF NOT WILL SAY --- 'PAIRING' AS CONNECTION TAKES
PLACE. CONNECT DEVICE IN THE NORMAL WAY TO -- 'MY BT'

Page 2 of 21
MODULE FITTED TO EACH SIDE
OF HEADBOARD
HEADPHONE SOCKET
PLUG A 3.5mm HEAD-PHONE
JACK PLUG INTO THIS SOCKET
AND SOUND FROM MAIN
SPEAKERS IS CUT OFF
USB CHARGING SOCKET
PLUG A STANDARD USB INTO
THIS SOCKET TO CHARGE ANY
DEVICE 5V 2.1A TOTAL
NOTE THIS USB IS FOR
CHARGING ONLY, CANNOT PLAY
MUSIC OR VIDEOS THROUGH
THE SYSTEM.
Warning
You must ensure that the mattress is on the bed frame before operating the lift mechanism – Failure
to do so could result in injury.
Keep hands clear of the mechanism when opening or closing the ottoman.
Beware of entrapment – Never reach in through the mechanism to access the storage area.
Always ensure that the ottoman is FULLY opened before accessing the storage area.
Do not exceed the maximum weight as specified in the table below:
•
Bed Bed Size Min Weight (kg) Max Weight (kg)
MONACO
OTTOMAN
TV BED
Single 10 25
Small Double 10 35
Double 10 40
King 15 45
Super King 20 50
•
•
•
•
Use caution when operating, always use the handle when lifting.
Note: This bed uses a pressurised mechanism.
To be operated by adults only．
Please ensure that children and pets are kept away from the bed when operating the lift mechanism.
Keep children and pets away from the storage area.
Do not overload the internal storage base.
Do not stand inside the internal storage area of the bed.
Before removing the mattress secure the frame to ensure it does not open unexpectedly.
Do not attempt to lie on the mattress when the ottoman is in the raised position.
When lifting the ottoman remove all bedding except the fitted sheet.
•
•
•
•
•
•
•
•
•
•
TO AVOID ACCIDENTS
TO ACCESS THE STORAGE AREA THE OTTOMAN FRAME
MUST BE FULLY OPENED AND FULLY CLOSED AFTERWARDS
Keep hands clear of the mechanism when operating the base system
Do not overload the internal storage base
Do not allow chlidren near the lift base when operating the mechanism
Do not stand inside the internal storage area of the bed
Do not reach into the storage area through the hinge mechanism
Don’t lift without mattress Ensure mattress is on before lifting
CAUTION
TO BE OPERATED BY ADULTS ONLY
KEEP CHILDREN OR PETS AWAY FROM THE STORAGE AREA
TO AVOID TRAPPING YOUR FINGERS, USE ONLY THE HANDLE TO LIFT AND LOWER THE BASE
BE CAREFUL WHEN LIFTING, ONLY LIFT WITH THE MATTRESS IN PLACE

Flat M8 washers Allen key for M8 bolts (5mm)
Bolts M8x30mm for fitting
media tray to side rail (3)
Plastic barrel nuts for
assembling media tray panels
Page 3 of 21
A x16
Bolts M8x30mm for
fitting side rails (3&4) to
headboard & footboard (1&2)
A x4
E x11 F x11
B x16
D x1
C x16
CARTON 1 - HEADBOARD CARTON 2 - FOOTBOARD
Hardware Pack for Bed Assembly
Hardware Pack for TV Installation
Hardware Pack for Media Tray Assembly
Spring M8 washers
C x4
Screws (5x50mm) for
assembling media tray panels
Aerial lead Cable clips
Mains power lead Cable ties
G x1 H x2 J x1 K x3 L x3
N x1
HDMI leads
TV Cables & Accessories plus Mattress Base Board Hinges
Remote control
TV Lift_Audio
The following items are in an accessory box, inside the TV Compartment,inside Carton 2
P1 x1 U x2
Allen key (4mm) Allen key (2.5mm)
b x1
FOOTEND CONNECTIONS
FOR SPEAKERS & USB
CABLES (P1 & P2)
HEADEND CONNECTIONS FOR
SPEAKERS & USB CABLES (P1 & P2)
HDMI 90° adapter
M x1
Gas-lift mechanisms
R x1 Pr
R(a) R(b)
Mattress stoppers
Flat M8 washers for fitting
media tray to side rail (3)
C
C
a x2
M8 x 25mm
Bolt sets Counter-sunk screw
sets (M6x12mm)
Counter-sunk screw
sets (M4x12mm)
(5 Pin)
P2 x1
(4 Pin)
Connection cablefor P1)
USB /headphone module
P2). Headboard speakers
C
C

Page 4 of 21
CARTON 3 - SIDE RAILS
(3) Side rail - with media tray （4）Side rail - without media tray
CARTON 5 - MEDIA TRAY
(5) Metal tie rails for mattress base boards x2 (6) Fabric hand strap x1
x1
(7) Remote control
holster
B x30 C x30
S x2 T x1
Q x4
Spring washers for M8
bolts & mattress stoppers
Flat M8 washers for bolts
(A) & mattress stoppers M8 Nuts for mattress stoppers
Spanner for M8 nuts
M8 Flange lock-nuts for
gas-lift piston stems
HARDWARE PACK FOR ASSEMBLY OF OTTOMAN MATTRESS BASE BOARDS
A x26
Bolts (M8x30) for fitting gas-lift
mechanisms R to headboard
& footboard (1&2).
For fitting metal tie rails (5)
and mechanisms (R) to
mattress base boards (13&14).
CARTON 4 - OTTOMAN MATTRESS BASES & STORAGE BASE BOARDS
（8）Media tray back panel （9）Media tray base panel
（10）Media tray side panel - LH （11）Media tray side panel - RH
(12) Storage base boards x2 (13) Mattress base board x1 (14) Mattress base board
x1

A x16 B x16 C x16
Page 5 of 21
1a
D
x1
R (a) x1 R (b) x1
AD
B
C
10mm
CHOOSE WHICH SIDE YOU WANT TO LIFT UP
OPEN FROM LEFT
B
A
C
D
BOLTS SHOULD BE IN CENTRE
OF LONG HOLES
R(b)
R(a)
1
2
ALIGN WITH BLUE LABELS
CHECK THIS DIAGRAM AND IF ACCESS IS NEEDED FROM LEFT SIDE OF BED, FIT
BOTH LIFT MECHANISMS TO RIGHT SIDE OF THE HEADBOARD & FOOTBOARD.
BOLT INTO THE HOLES MARKED (R) WITH BLUE LABELS.
THE MECHANISMS ARE LABELED R(a) &
R(b) PLEASE CAREFULLY FOLLOW THE
DIAGRAM BELOW.
LEFT SIDE

A x16 B x16 C x16
D
x1
R (a) x1 R (b) x1
Page 6 of 21
1b
AD
B
C
10mm
B
A
C
D
BOLTS SHOULD BE IN CENTRE
OF LONG HOLES
OPEN FROM RIGHT
R(b)
R(a)
1
2
ALIGN WITH RED LABELS
CHECK THIS DIAGRAM AND IF ACCESS IS NEEDED FROM RIGHT SIDE OF BED,
FIT BOTH LIFT MECHANISMS TO LEFT SIDE OF THE HEADBOARD &
FOOTBOARD. BOLT INTO THE HOLES MARKED (L) WITH RED LABELS.
THE MECHANISMS ARE LABELED R(a) &
R(b) PLEASE CAREFULLY FOLLOW THE
DIAGRAM BELOW.
RIGHT SIDE

Page 7 of 21
2
3
3
4
1&2
3or4
Ax4 Bx4
Cx4
D
x1
A
B
CD
90%
(3) IS ON LEFT SIDE
C
C
C
Always to LEFT side rail 3 or 4, irrespective of which side is chosen
to be plain or with media tray, fit Headboard Speaker/USB
connection cables (P1 & P2) tucking neatly under Velcro flaps.
CHOOSE SIDE FOR MEDIA TRAY THEN
FIT THE LEFT SIDE RAIL (3) or (4)
C
P
(4) IS ON LEFT SIDE

Page 8 of 21
4
5
Connect Main Power Lead to
your wall socket - for safety,
this must be an earthed supply.
G
On the two connection cables P1 & P2, connect
plugs and sockets together, these are clearly labeled.
HEADEND
FOOTEND
1
2

Page 9 of 21
6
7
TIP:
BEFORE FITTING THE TV,
PUSH CABLES THROUGH
EACH DUCT FROM THE TOP.
CHOOSE THE BEST SIDE TO
USE DEPENDING ON WHERE
THE CONNECTION PORTS
ARE, ON BACK OF YOUR TV.
NEVER CROSS CABLES FROM
ONE SIDE TO THE OTHER.
Note: For illustration purposes
only, TV connections may vary.
TV Power Lead
supplied with your own TV.
N
Press the “UP” button
to raise the TV lift.
H
J
HDMI
AERIAL
G
MAIN POWER
SUPPLY

Page 10 of 21
8
a
a
Loosen Tighten
b
IF SCREWS ARE SUPPLIED WITH TV, PLEASE USE THOSE IN PREFERENCE
TV Installation - Normal Vesa Fixing
a x2
b x2
M8 x 25mm
Bolt sets Counter-sunk screw
sets (M6x12mm)
Counter-sunk screw
sets (M4x12mm)
Allen Key (4mm) Allen Key (2.5mm)

aa
b
100mm
100mm
IF SCREWS ARE SUPPLIED WITH TV, PLEASE USE THOSE IN PREFERENCE
REMOVE CROSS-BRACKET
AND FIX IT DIRECTLY TO BACK OF TV
TV Installation - 100x100 Vesa Fixing
Page 11 of 21
9a
9b
a x2
b x2
M8 x 25mm
Bolt sets Counter-sunk screw
sets (M6x12mm)
Counter-sunk screw
sets (M4x12mm)
Allen Key (4mm) Allen Key (2.5mm)

Page 12 of 21
9c
Loosen Tighten
i.
ii.

Page 13 of 21
10
90º ADAPTER
TV Power Lead supplied
with your TV
PLUG IN - KEEP
ALL CABLES TIGHT
- USE CLIPS & TIES
PROVIDED.
H
K
L
H
J
M
Keep wires tight - peel off
cover from cable clips &
adhere to back of TV.
Note: For illustration purposes
only, TV connections may vary.
OPTICAL
REMOVE DUST-CAP

Page 14 of 21
11
12
TV Power Lead
supplied with your TV
Press the “DOWN” button
to lower the TV lift.
J
N
IMPORTANT: Be careful to keep the two HDMI Leads (H) on top of the Base Boards.
Main power lead (G) and Aerial lead (J) should be kept under the base boards & fed out under the
headboard so you can connect to your wall sockets.
12

Page 15 of 21
14
E
E
Ex11
8
9
10
11
13
Fx7
Fx2
F
Fx11
8
11
Fx2
10
E x7

Page 16 of 21
15
16
AD
C
Ax4
Cx4
Dx1
Ax4 Bx4
Cx4
D
x1
A
B
CD
100%
4
3
1&2
3or4
WHEN ALL BOLTS HAVE BEEN FITTED AND THE BED
IS SQUARED UP AS IN THE DIAGRAM, TIGHTEN 100%
FIT THE RIGHT SIDE RAIL (3) or (4)
FIT THE MEDIA TRAY

Page 17 of 21
17
B
A
C
D
C
T
Q
B
Ax12 B
x16 C
T
x16
Dx1 x1
Ux2
Qx4
6
5
14
13
5
5
U
Ux2
13 & 14

Page 18 of 21
18
Sx2 Tx1
T
S
N
X
TV
R (a) & R (b)
LIFT UP HINGE
SLIDE PISTON ONTO STEM
DO NOT OVERTIGHTEN
LEAVE A SMALL GAP
FIT FLANGE LOCK-NUT (S)
FIT THE REMOTE CONTROL HOLSTER LEFT or RIGHT

Page 19 of 21
19
B
A
C
D
Ax6 B
x6 Cx6 Dx1
Note: Be very careful what
you store under the bed -
the top of an item, like a
suitcase or a box, must not
touch the slats or they may
be damaged. Maximum
storage height is 320mm.
1 Before moving the mattress base board, place a mattress on top of the board as without a mattress in place the
speed of movement is quick and may cause injury so be careful.
2 Carefully lower the base board with the hand-strap ensuring the board edges are aligned with the side rails;
there should be an even edges on each side. If not aligned, check bed is still square and if it is, but edges are
still not even, re-align the base boards.
3 Depending on the weight of the mattress, the rising speed will vary so be careful until you get used to the speed.
Always use the strap to lift or lower the mattress base board - keep fingers well away from the moving parts.
4 To help prevent any accidental entrapment, please make certain the ottoman is lifted right to the top of it's travel
before putting in or retrieving an item from the storage area.
5 When finished, slowly lower the frame back to the lower rest position using the hand strap only.
When fully assembled and with the mattress in position, please raise & lower the ottoman 4/5 times to
ensure the gas pistons are fully lubricated.

Page 20 of 21
TV BED SAFETY INFORMATION
GENERAL INFORMATION
It is very important not to place any vessel containing liquids, e.g. drinks or vase of flowers, on top of the TV footboard
which may accidentally spill and enter the TV compartment as this could cause damage to the TV and/or the TV lifting
equipment.
If this happens, please contact your retailer.
Do not expose the bed to an undue level of heat - keep away from radiators.
Never allow anyone to sit on the foot end of the bed - keep children well away from moving parts.
To keep bed clean, we recommend that it be wiped over with a slightly dampened cloth or if fabric, use a light vacuum
cleaner; disconnect power before cleaning.
Supplied with the bed is a remote control to operate the TV lift and when you fit your own TV there is a remote control to
operate it as well. Both these remotes use batteries - there are no batteries in the rest of the equipment.
There are strict controls for disposal of batteries - your local council can advise on how to safely dispose of them.
Never burn batteries on an open fire as they could explode.
IMPORTANT POWER INFORMATION
It is essential that the Mains Power Lead is connected to an earthed socket be it a wall socket or extension lead - otherwise
there is risk of damage or even electric-shock.
The socket providing the power must be accessible at all times in case you need to switch off the power quickly.
During an electrical or lightening storm - disconnect the power completely as a precaution.
Always un-plug the power when going on holiday or when the bed is not used for an extended period.
If you have young children in the home always disconnect the power at the wall socket for extra safety.
Power outlets, extension leads or adapters must not be overloaded beyond their limit - this can result in fire or electric shock.
Leads supplied with this bed, or other approved mains powered extension leads used to power the equipment, must not be
placed where they can be walked on - this is dangerous and could lead to accidents.
Do not interfere with or modify any cables already fitted and do not add any extra media leads unless they are routed through
the ducts as shown. All leads must be tightly connected to back of TV, never hanging loose.
Never touch moving parts or any part of the equipment - if something needs to be checked, disconnect the power first.
Do not insert anything into the footboard as this could seriously damage the TV and/or the TV lifting equipment and could, if
done carelessly, cause serious damage or injury.
If the equipment doesn't operate normally or if there is an unusual noises, disconnect the power.
TELEVISION INSTALLATION
Before fixing the mattress base boards to the bed, please follow the television installation instructions. below.
Raise the TV lift by pressing the top UP button of the remote control.
Connect TV to the mounting bracket using the TV installation kit packed with the main hardware in the accessory box inside
carton 2. If screws are supplied with your TV, use those in preference.
If necessary mounting plate can easily be adjusted to move up or down to align with VESA holes in the TV.
Connect the TV power lead (supplied with TV) by passing plug down one of the ducts, plugging it into the TV power adapter
if supplied with your TV, then into the TV power socket which is on the face of footboard.This socket is only to be used for
the TV as the supply is not permanent.
Connect the aerial & HDMI cable by passing down the appropriate duct.
If required, connect your own media cables through either of the ducts - connecting your media equipment when ready.
Please use the cable clips & cable ties to make certain there are no loose wires to snag
or get trapped.
The TV can now be operated following the TV operation guide supplied with your TV.
When finished viewing, lower the TV back into the footboard by pressing DOWN button of the remote control.
The TV will retract into the footboard automatically - for safety, power shall be turned off to the TV when it reaches the
bottom rest position.
Note that when the TV is operating and Bluetooth is selected, the TV picture will stay on screen - either turn off TV or press
down button to lower to the resting position, TV is turned off but music will still play.
When the up button is pressed - the TV lifting column rises and power to the TV turns back on automatically.
TROUBLE SHOOTING
If your equipment does not operate please check all the power connections, to the wall and to the socket in the footboard.
Make sure TV is switched on. (Note: TV will only work when it is in the up position).
Follow instructionsto make certain pairing of the remote control & TV lift has not been lost.
If the television or TV Lift still fails to operate contact your retailer.
IMPORTANT
:
Care should be taken when connecting electrical iems. I f in any doubt please consult an approved
electrician to advise you on electrical supply to achieve safe connections, to the electrical equipment of the TV Bed.