TV Bedstore SHELDON User manual

x2
1.5 Hrs
Double & King Super King
V1 230605 Page 1 of 16
An instructional video of the Operation of the Ottoman Lift Up system is available via YouTube using
the
following address: https://youtu.be/hyq4zm7h_yU
Press once and TV will rise to it's upper working position. Power to the TV will
be connected automatically
Press once and TV Lift will stop.
Torch
Code Matching
Code Matching (pairing): occasionally pairing is lost, perhaps due to atmospheric conditions,
To re-pair - press and hold the code matching button whilst connecting the power by plugging
the mains cable into the control box of the TV lift on the base of the footboard.
Continue to press the button for another 5 seconds then press the up or down button to
successfully match the code.
Regularly check the batteries and if necessary re-place them - x3 pcs AAA size.
Press once and TV will go down - as soon as the lower resting position is
reached power to the TV is switched off to prevent it overheating.
GENERAL INFORMATION
It is very important not to place any vessel containing liquids, e.g. drinks or vase of flowers on top of the TV footboard that may
accidentally spill and enter the TV compartment as this could cause damage to the TV and/or the TV lifting equipment. If this
happens turn off the power and contact your retailer.
Do not expose the bed to an undue level of heat - keep away from radiators.
Never allow anyone to sit on the foot end of the bed - keep children well away from moving parts.
To keep your bed clean, we recommend that it be wiped over with a slightly dampened cloth, or if fabric, use a light vacuum
cleaner; disconnect power before cleaning.
Supplied with the bed is a remote control to operate the TV Lift and there will be one to operate the television itself. Both these
remotes will be supplied with batteries - there are no batteries in the rest of the equipment.
When it is time to change the batteries there are strict controls for disposal of the old ones - your local council can advise
on how to safely dispose of them. Never burn batteries on an open fire as they could explode.
SHELDON OTTOMAN TV BED
ASSEMBLY INSTRUCTIONS

Page 2 of 16
SHELDON
OTTOMAN
TV BED
Warnings
You must ensure that the mattress is on the bed frame before operating the lift
mechanism. Failure to do so could result in injury.
Keep hands clear of the mechanism when opening or closing the ottoman.
Beware of entrapment – Never reach in through the mechanism to access the storage
Always ensure that the ottoman is FULLY opened before accessing the storage area.
Do not exceed the maximum weight as specified in the table below:
•
•
•
•
•
Use caution when operating, always use the handle when lifting.
Note: This bed uses a pressurised mechanism.
To be operated by adults only
Please ensure that children and pets are kept away from the bed when operating the
lift mechanism.
Keep children and pets away from the storage area.
Do not overload the internal storage base.
Do not stand inside the internal storage area of the bed.
Before removing the mattress secure the frame to ensure it does not open unexpectedly.
Do not attempt to lie on the mattress when the ottoman is in the raised position.
When lifting the ottoman remove all bedding except the fitted sheet.
•
•
•
•
•
•
•
•
•
•
Don’t lift without mattress Ensure mattress is on before lifting
WARNING: ONLY USE THE HANDLE TO LIFT &
LOWER THE BED FRAME TO
AVOID TRAPPING FINGERS!
SAFETY WARNING
PLEASE DO NOT ALLOW CHILDREN
OR PETS INSIDE THE STORAGE AREA.
SAFETY WARNING
PLEASE BE CAREFUL WHEN LIFTING.
ONLY LIFT WITH MATTRESS ON TOP.
TO BE OPERATED BY ADULTS ONLY.
TO AVOID ACCIDENTS
TO ACCESS THE STORAGE AREA THE OTTOMAN FRAME
MUST BE FULLY OPENED AND THEN FULLY CLOSED AFTERWARDS
Bed Bed Size Min Weight (kg) Max Weight (kg)
Double 10 40
King 15 45
Super King 20 50
area.
Note: Be very careful
what you store under
the bed - the top of an
item, like a box or a
suitcase, must not
touch the slats or they
may be damaged.
Maximum storage
height is 250mm.

Page 3 of 16
Components Packed in carton 1 Components Packed in carton 2
Angle bracket - LH Hooks Angle bracket - RH Hooks
Bolt sets (M8x35mm) for
fitting side rails (3) to
headboard & footboard
(1&2)
Bolt sets (M8x35mm) for
fitting lift mechanism to
footboard (2)
Bolt sets (M8x65mm) for
fitting lift mechanism to
headboard (1)
Bolt sets (M8x50mm) for
fitting metal slat frame to
lift mechanism (7&8)
Bolt sets (M8x20mm) for
fitting corner brackets L&R
Allen key for M6 bolts Allen key for M8 bolts
HARDWARE FOR ASSEMBLING THE BED
A x12 E x4
Bolt sets (M6x45mm) for
fitting ‘U’ shape cross
bar to side rails
F x12
Bolt sets (M6x20mm) for
fitting brackets(6&13) to
side rails
G x1 H x1
D x12
L x2 M x2
HARDWARE FOR ASSEMBLING THE BED - PACKED IN CARTON 2
M8 Spring Washer M8 Flat Washer
Spanner for flanged
M8 lock-nuts
Metal connection plate Flanged M8 lock-nuts
HARDWARE FOR ASSEMBLING THE METAL SLAT FRAME
A x4 C x6
N x2 O x10
B x6
P x1 Q x6 R x4
HARDWARE FOR ASSEMBLING THE METAL SLAT FRAME - PACKED IN CARTON 2
(6) Angledcorner bracket x2
(11) Mattress Stopper x2
(13) Support bracket x2
Bolt sets (M8x20mm) for
fitting metal connection plate
D x4

Components Packed in carton 3
Components Packed in carton 4
(3) Side Rails x2
(4) (5)
(9) (12)
(10)
(7) (8)
x2
Page 4 of 16
TV INSTALLATION KIT
HARDWARE FOR ASSEMBLING THE BED & FITTING THE TV - PACKED IN CARTON 2
Allen Key (4mm) Allen Key (2.5mm)
(M6x12mm)
Counter-Sunk Screws Counter-Sunk Screws
(M4x12mm)
Cable ClipsPower Lead - 3 metre Cable Ties
S x1 W x3V x3
CABLES & ACCESSORIES FOR TV INSTALLATION
Y x1
Screw-Washer Sets
(M8x25mm)
Use 5mm Allen Key (D)
Remote Control
a x2
b x2
Spacer Rails for
Lift Mechanism
‘U’ Shape Cross Bar
Lift Mechanism - LH Lift Mechanism - RH
Gas Lift Pistons
Metal Slat Frame for Double or King Size
(17)
(14)
Metal Slat Frame for Super King Size
Fabric Base Cover
Fabric Hand Strap
x1 x1 x1
x1 x1
x1
x1
x2

Page 5 of 16
3
3
3
1
1
2
2
x2
A
x12
H
x1
L
x2
H
x1
M
x2
D
D x3
L
M
D x3
A x3
L
M
A x3
x12
2
1

3
12
5
E x2
Page 6 of 16
4
3
G
x1
E
x4
Fit the fabric base cover (12) evenly around the inside of the bed.
3
3

Page 7 of 16
5a
6a
Please choose which side of the slat-frame to lift up to reach into the storage area.
To lift from the LEFT, follow Step (5a, 6a & 14a) to lift from the RIGHT, steps (5b, 6b & 14b).
Depending which size of bed you have purchased, use the relevant hardware for the Double
size, King size or Super-King size bed.
G
x1
F
x12
G
x1
R
x4
A
x4
1
1
2
2
1
1
2
2
448
7
13 6
F x2 F x4
A x4
R x4
100%
Left

5b
Page 8 of 16
6b
G
x1
F
x12
G
x1
R
x4
A
x4
1
1
2
2
1
1
2
2
4847
A x4
R x4
6
F x4
13
F x2
100%
Right

Page 9 of 16
8
7
G
x1
N
x2
D
x4
S
10
11
10
17
17
D x2
D x2
N
N
x5
Connect the mains power lead
(S) to your wall socket - for
safety this must be an earthed
power supply.
Double & King Size Super King Size

9
Page 10 of 16
10
Y
Press the "UP" button
to raise the TV lift.
TV Power Lead supplied
with your own TV
Leads for
HDMI or Aerial
If required, please
purchase HDMI
leads about 3mt
long and length of
aerial lead to suit
the position of your
wall socket.
TIP:
BEFORE FITTING THE TV,
PUSH CABLES THROUGH
EACH DUCT FROM THE TOP.
CHOOSE THE BEST SIDE TO
USE DEPENDING ON WHERE
THE CONNECTION PORTS
ARE ON BACK OF YOUR TV.
NEVER CROSS CABLES FROM
ONE SIDE TO THE OTHER.
Note: For illustration purposes only, TV connections may vary.

Page 11 of 16
11
x2
TV INSTALLATION KIT
a
Screw-Washer set (M8/M6/M4)
a
a
Loosen Tighten
x1
Allen Key (5mm/4mm/2.5mm)b

Page 12 of 16
12
V
W
TV power lead supplied
with your own TV
PLUG IN - KEEP ALL CABLES TIGHT
- USE CLIPS & TIES PROVIDED.
Keep wires tight - peel
off cover from cable clips
& adhere to back of TV.
Note: For illustration purposes only, TV connections may vary.

Y
Page 13 of 16
13
TV power lead
supplied with your
own TV
Press the “DOWN” button
to lower the TV lift.
Aerial lead supplied
by yourself if required

Page 14 of 16
14a
14b
C
x6
G
x1
B
x6
P
x1
Q
x6
O
x6
Double or King Size
Double & King Size
Super King Size
Super King Size
Fit the bolt sets
but please do not
tighten fully yet.
Fit the bolt sets but please
do not tighten fully yet.
LIFT FROM RIGHT SIDE
MAKE SURE THE MATTRESS STOPPERS AND HAND STRAP
ARE ON THE CORRECT SIDE OF THE BED AS SHOWN
Q
C
B
C
O
Q
C
B
C
O
LIFT FROM LEFT SIDE
MAKE SURE THE MATTRESS STOPPERS AND HAND STRAP
ARE ON THE CORRECT SIDE OF THE BED AS SHOWN
10
10
14
17
17 14

Page 15 of 16
16
15
P
x1
O
x4
H
x1
P
x1
O
O
Fit the pistons (9) sliding the
stems (x) over the axles (y).
Tighten lock nuts (O) with
spanner (P) but please DO NOT
over-tighten, a small gap needs
to be left so stems can move
freely - if too tight the frame will
be hard to lift so this is important.
SMALL GAP
y
x
Carefully lay frame down. Make sure there is an
even gap each side of about 8 mm, as in the sketch.
8 mm
Hold frame securely then tighten all six bolt sets
100% using spanner (P) & Allen key (H).
9

Page 16 of 16
80
25
205
830
30
W
H
L
40
Top of slat to
top of side rail
290
Floor to top
of slat
IMPORTANT: Care should be taken when connecting electrical items. If you are in any doubt about the connections
please consult an approved electrician. If you still have a problem please contact your retailer for advice.
IMPORTANT POWER INFORMATION
Before fixing the mattress baseboards to the bed, please follow the instructions below:
Plug in the main power supply lead supplied with your bed; this is packedi inside the TV footboard Pack 2.
It is essential that this power lead is connected to an earthed socket be it a wall socket or extension lead - otherwise there is risk
of damage or even electric-shock.
The wall socket providing the power must be accessible at all times in case you need to switch off the electric supply.
Power cable supplied with this bed or other approved mains powered extension leads used to power your equipment must not be
placed where they can be walked on - this is dangerous and could lead to accidents.
Power outlets, extension leads or adapters must not be overloaded beyond their limit - this can result in fire or electric shock.
During an electrical or lightening storm - disconnect the power completely as a precaution.
Always un-plug the power when going on holiday or when the bed is not used for an extended period.
If you have young children in the home always disconnect the power at the wall socket for extra safety.
Do not interfere with or modify any cables already fitted and do not add any media cables unless they are routed through the
ducts as shown. All leads must be tightly connected to back of TV, never hanging loose where they can get trapped.
Never touch moving parts or any part of the equipment - if something needs to be checked, disconnect the power first.
Do not insert anything into the footboard as this could seriously damage the TVand/or the TV lifting equipment and could, if done
carelessly, cause serious damage or injury.
If the equipment doesn't operate normally or if there is any unusual noises, disconnect the powera nd contact your retailer for
advice.
TELEVISION INFORMATION
Please follow the assembly steps for initial operation of the TV Lift, your TV and any media cables required.
Push the television power plug (supplied with your own TV), into it's own special socket which is on the face of the footboard
clearly shown in the instructions. For safety and to prevent overheating, this socket is only to be used for the television as it does
not have a constant power supply.
Raise the TV Lift by pressing the UP button of the remote control.
If required you can connect media cables the television ports.
Please use the cable clips & cable ties to make certain there are no loose wires to snag or get trapped.
The television can now be operated following the TV User Guide.
When finished viewing, lower the television back into the footboard by pressing the DOWN button of the remote control.
For safety and to stop any overheating, power to the television is switched off when lift reaches the bottom rest position.
When the UP button is pressed - the TV Lifting Column rises and power is turned back on automatically.
TROUBLE SHOOTING
oIf your equipment does not operate please check all the electrical connections to the wall socket and check that
electricity is reaching the main power input plug bringing power to the footboard.
oMake sure that the TV is switched on - but note that the television will only work when it is in the up position.
oCheck that the remote control has not lost its connection with the TV Lift - please see pairing instructions on Page (1).
Double: 670 x 53 x 9
King:
Super King:
Double: 2200 x 1430 x 1155
King: 2300 x 1580 x 1155
Super King: 2300 x 1880 x 1155
Internal Dimensions (LWH mm)
Double:
King:
Super King:
Distance between slats (mm)
Double: 72
King & Super King: 70
Ottoman Piston Rating
Double & King: 800N
Super King: 900N
Technical Specifications
Max TV Size: 980 x 570 x 85 (WHDmm)
Overall Dimensions (LWH mm)
Slat Dimensions (mm)
745 x 53 x 9
595 x 53 x 9
1930 x 1380 x 250
2030 x 1530 x 250
2030 x 1830 x 250