TVT TD-2104TS User manual

HD TVI DVR
Quick Start Guide
1 Notes
● Please read this instruction carefully for correct use of the
product and preserve it for reference purposes.
● All the examples and pictures used here are for reference
only.
● There may be several technically incorrect places or
printing errors in this manual. The updates will be added
into the new version of this manual. The contents of this
manual are subject to change without notice.
● This device should be operated only from the type of power
source indicated on the marking label. The voltage of the
power must be verified before using the same.
This series of the product supports 1 SATA hard drive. Please
make sure that the device is powered off before the installation.
The pictures of the installation are only for reference, please take
the real object as the standard.
Please check the device and the accessories after getting the
device. If there are any damages, shortages or defects, please
contact your dealer immediately.
3 HDD Installation
2 Packing Check The interfaces of the rear panel are for reference only.
4 Rear Panel Instruction
5 Startup & Shutdown
Go to “Main Menu” and then select “Shutdown” icon. This
will bring up a shutdown window. The device will shut
down by clicking “OK” button. Then disconnect the power.
► NAT Settings
① The DVR shall be powered on and connected to the network.
② Go to Main Menu→Setup→Network→Network. Refer to
Fig 1. You can obtain the IP address, Subnet Mask and Gateway
automatically. You can also manually enter them according to
the actual network situation. Please make sure the network
segment is the same as that of the network which is used.
③ Set the preferred or alternative DNS Server. Click “Apply”
to save the parameters.
④ Go to Main Menu→Setup→Network→NAT tab. Refer to
Fig 2.
After the wizard setup, you can see the live image. Right click
to pop up a menu toolbar. Click Main Menu button. This will
take you to see a login box. The default username is admin;
the default password is 123456. Enter username and password
and click “Login” button to go to the main menu setup.
6 Login
7 NAT
►Startup
① Connect the monitor.
② Connect the power.
③ The device will boot and the power indicator will display
blue.
④ A wizard window will pop up.
►Shutdown
AUDIO OUT
DC12V
USB
LAN
VGA
AUDIO IN
VIDE O IN
1
3
24
Inte rnet
① Loosen the screws to open the
cover.
② Get the HDD ready.
⑤ Turn over the machine and secure
the HDD with the screws.
③ Put the HDD onto the bottom of
the device.
④ Connect the power and data
cables.
⑥ Install back the cover and secure
it with the screws.

HD TVI DVR
Quick Start Guide
1 Notes
● Please read this instruction carefully for correct use of the
product and preserve it for reference purposes.
● All the examples and pictures used here are for reference
only.
● There may be several technically incorrect places or
printing errors in this manual. The updates will be added
into the new version of this manual. The contents of this
manual are subject to change without notice.
● This device should be operated only from the type of power
source indicated on the marking label. The voltage of the
power must be verified before using the same.
This series of the product supports 1 SATA hard drive. Please
make sure that the device is powered off before the installation.
The pictures of the installation are only for reference, please take
the real object as the standard.
Please check the device and the accessories after getting the
device. If there are any damages, shortages or defects, please
contact your dealer immediately.
3 HDD Installation
2 Packing Check The interfaces of the rear panel are for reference only.
4 Rear Panel Instruction
5 Startup & Shutdown
Go to “Main Menu” and then select “Shutdown” icon. This
will bring up a shutdown window. The device will shut
down by clicking “OK” button. Then disconnect the power.
► NAT Settings
① The DVR shall be powered on and connected to the network.
② Go to Main Menu→Setup→Network→Network. Refer to
Fig 1. You can obtain the IP address, Subnet Mask and Gateway
automatically. You can also manually enter them according to
the actual network situation. Please make sure the network
segment is the same as that of the network which is used.
③ Set the preferred or alternative DNS Server. Click “Apply”
to save the parameters.
④ Go to Main Menu→Setup→Network→NAT tab. Refer to
Fig 2.
After the wizard setup, you can see the live image. Right click
to pop up a menu toolbar. Click Main Menu button. This will
take you to see a login box. The default username is admin;
the default password is 123456. Enter username and password
and click “Login” button to go to the main menu setup.
6 Login
7 NAT
►Startup
① Connect the monitor.
② Connect the power.
③ The device will boot and the power indicator will display
blue.
④ A wizard window will pop up.
►Shutdown
AUDIO OUT
DC12V
USB
LAN
VGA
AUDIO IN
VIDE O IN
1
3
24
Inte rnet
① Loosen the screws to open the
cover.
② Get the HDD ready.
⑤ Turn over the machine and secure
the HDD with the screws.
③ Put the HDD onto the bottom of
the device.
④ Connect the power and data
cables.
⑥ Install back the cover and secure
it with the screws.

HD TVI DVR
Quick Start Guide
1 Notes
● Please read this instruction carefully for correct use of the
product and preserve it for reference purposes.
● All the examples and pictures used here are for reference
only.
● There may be several technically incorrect places or
printing errors in this manual. The updates will be added
into the new version of this manual. The contents of this
manual are subject to change without notice.
● This device should be operated only from the type of power
source indicated on the marking label. The voltage of the
power must be verified before using the same.
This series of the product supports 1 SATA hard drive. Please
make sure that the device is powered off before the installation.
The pictures of the installation are only for reference, please take
the real object as the standard.
Please check the device and the accessories after getting the
device. If there are any damages, shortages or defects, please
contact your dealer immediately.
3 HDD Installation
2 Packing Check The interfaces of the rear panel are for reference only.
4 Rear Panel Instruction
5 Startup & Shutdown
Go to “Main Menu” and then select “Shutdown” icon. This
will bring up a shutdown window. The device will shut
down by clicking “OK” button. Then disconnect the power.
► NAT Settings
① The DVR shall be powered on and connected to the network.
② Go to Main Menu→Setup→Network→Network. Refer to
Fig 1. You can obtain the IP address, Subnet Mask and Gateway
automatically. You can also manually enter them according to
the actual network situation. Please make sure the network
segment is the same as that of the network which is used.
③ Set the preferred or alternative DNS Server. Click “Apply”
to save the parameters.
④ Go to Main Menu→Setup→Network→NAT tab. Refer to
Fig 2.
After the wizard setup, you can see the live image. Right click
to pop up a menu toolbar. Click Main Menu button. This will
take you to see a login box. The default username is admin;
the default password is 123456. Enter username and password
and click “Login” button to go to the main menu setup.
6 Login
7 NAT
►Startup
① Connect the monitor.
② Connect the power.
③ The device will boot and the power indicator will display
blue.
④ A wizard window will pop up.
►Shutdown
AUDIO OUT
DC12V
USB
LAN
VGA
AUDIO IN
VIDEO IN
1
3
24
Inte rnet
① Loosen the screws to open the
cover.
② Get the HDD ready.
⑤ Turn over the machine and secure
the HDD with the screws.
③ Put the HDD onto the bottom of
the device.
④ Connect the power and data
cables.
⑥ Install back the cover and secure
it with the screws.

450041001002 A0
Right click the mouse in the live interface to pop up the menu
toolbar. Click the little triangle button beside button to set
playback time (eg. 5 minutes). Then click button to play the
record from the past 5 minutes. You may control the video by
clicking the corresponding buttons, such as, forward, play/pause,
stop, etc. If you want to play the record by searching the specific
time and date, event or file, you may refer to the DVR User
Manual for details.
9 Manual Recording
Before recording, please install and format a HDD. Right
click the mouse in the live interface to pop up the following
menu toolbar. Click button to start recording.
10 Playback
Device Serial Number: The MAC address of the DVR (Go to
Main Menu→Information→Network to check the MAC address
of the DVR).
Username: The username of DVR. The default username
is admin.
Password: The password of DVR. The default password is
123456.
Note: Before setting UPnP function, please configure the correct local
IP address, subnet mask, gateway and DNS according to the router.
Make sure the HTTP port and data port are correctly set. Make sure the
router supports UPnP function.
Fig 2
► NAT Access
After finishing the NAT settings, input www.autonat.com
in the address bar to go to the IE client. If you are the first time
to access the NAT, you shall download and install the ActiveX
according to the popup tips. After installing ActiveX successfully,
it will pop up the login box.
8 DDNS & UPnP Function
► UPnP
You can use the UPnP function to enable the fast connection
of the device to WAN via a router without port mapping.
① Go to Other Settings tab and enable the UPnP and click
“Apply” button to save.
② Enable the UPnP function in the router.
► Quick DDNS Setup
You may set up DDNS to be used in connection when your
device is set to use PPPoE as its network connection.
① Go to Main Menu→Setup →Network→Other Settings
interface.
② Make sure the DDNS type “ www.autoddns.com” . Then
self-define the host domain. After you register it successfully,
save the settings by clicking “Apply” button. Now, you can
remotely access the device using the domain name via WAN.
Fig 1
Enter device serial number
Enter Username
Enter Password
Login
⑤ Enable NAT and input the NAT Server (The default NAT
Server is www.autonat.com) .
⑥ Click “Apply” to save the parameters.

450041001002 A0
Right click the mouse in the live interface to pop up the menu
toolbar. Click the little triangle button beside button to set
playback time (eg. 5 minutes). Then click button to play the
record from the past 5 minutes. You may control the video by
clicking the corresponding buttons, such as, forward, play/pause,
stop, etc. If you want to play the record by searching the specific
time and date, event or file, you may refer to the DVR User
Manual for details.
9 Manual Recording
Before recording, please install and format a HDD. Right
click the mouse in the live interface to pop up the following
menu toolbar. Click button to start recording.
10 Playback
Device Serial Number: The MAC address of the DVR (Go to
Main Menu→Information→Network to check the MAC address
of the DVR).
Username: The username of DVR. The default username
is admin.
Password: The password of DVR. The default password is
123456.
Note: Before setting UPnP function, please configure the correct local
IP address, subnet mask, gateway and DNS according to the router.
Make sure the HTTP port and data port are correctly set. Make sure the
router supports UPnP function.
Fig 2
► NAT Access
After finishing the NAT settings, input www.autonat.com
in the address bar to go to the IE client. If you are the first time
to access the NAT, you shall download and install the ActiveX
according to the popup tips. After installing ActiveX successfully,
it will pop up the login box.
8 DDNS & UPnP Function
► UPnP
You can use the UPnP function to enable the fast connection
of the device to WAN via a router without port mapping.
① Go to Other Settings tab and enable the UPnP and click
“Apply” button to save.
② Enable the UPnP function in the router.
► Quick DDNS Setup
You may set up DDNS to be used in connection when your
device is set to use PPPoE as its network connection.
① Go to Main Menu→Setup →Network→Other Settings
interface.
② Make sure the DDNS type “ www.autoddns.com” . Then
self-define the host domain. After you register it successfully,
save the settings by clicking “Apply” button. Now, you can
remotely access the device using the domain name via WAN.
Fig 1
Enter device serial number
Enter Username
Enter Password
Login
⑤ Enable NAT and input the NAT Server (The default NAT
Server is www.autonat.com) .
⑥ Click “Apply” to save the parameters.

450041001002 A0
Right click the mouse in the live interface to pop up the menu
toolbar. Click the little triangle button beside button to set
playback time (eg. 5 minutes). Then click button to play the
record from the past 5 minutes. You may control the video by
clicking the corresponding buttons, such as, forward, play/pause,
stop, etc. If you want to play the record by searching the specific
time and date, event or file, you may refer to the DVR User
Manual for details.
9 Manual Recording
Before recording, please install and format a HDD. Right
click the mouse in the live interface to pop up the following
menu toolbar. Click button to start recording.
10 Playback
Device Serial Number: The MAC address of the DVR (Go to
Main Menu→Information→Network to check the MAC address
of the DVR).
Username: The username of DVR. The default username
is admin.
Password: The password of DVR. The default password is
123456.
Note: Before setting UPnP function, please configure the correct local
IP address, subnet mask, gateway and DNS according to the router.
Make sure the HTTP port and data port are correctly set. Make sure the
router supports UPnP function.
Fig 2
► NAT Access
After finishing the NAT settings, input www.autonat.com
in the address bar to go to the IE client. If you are the first time
to access the NAT, you shall download and install the ActiveX
according to the popup tips. After installing ActiveX successfully,
it will pop up the login box.
8 DDNS & UPnP Function
► UPnP
You can use the UPnP function to enable the fast connection
of the device to WAN via a router without port mapping.
① Go to Other Settings tab and enable the UPnP and click
“Apply” button to save.
② Enable the UPnP function in the router.
► Quick DDNS Setup
You may set up DDNS to be used in connection when your
device is set to use PPPoE as its network connection.
① Go to Main Menu→Setup →Network→Other Settings
interface.
② Make sure the DDNS type “ www.autoddns.com” . Then
self-define the host domain. After you register it successfully,
save the settings by clicking “Apply” button. Now, you can
remotely access the device using the domain name via WAN.
Fig 1
Enter device serial number
Enter Username
Enter Password
Login
⑤ Enable NAT and input the NAT Server (The default NAT
Server is www.autonat.com) .
⑥ Click “Apply” to save the parameters.