Hybrid DVR
Quick Start Guide
1. Notes
● Please read this instruction carefully before operating the unit and
keep it for further reference.
● All the examples and pictures used here are for reference only.
● The contents of this manual are subject to change without notice.
● This device should be operated only from the type of power source indicated
on the marking label. The voltage of the power must be verified before using
the same.
The interfaces of the rear panels are for reference only.
4. Rear Panel Instruction
5. Startup & Shutdown
8. Network Configuration & Add IP Camera
7. Analog Camera Connection
You must configure the wizard if you start the DVR for the first time.
Please change the
password as needed and then click “Edit Security Question” to set questions
and answers for retrieving password.
The default
username is admin and the default password is 123456.
►Startup
① Connect the monitor and the power.
② The device will boot and the power indicator will display blue.
③ A wizard window will pop up.
►Shutdown
Click “Start” and then select “Shutdown” icon. This will bring up a shutdown
window. The device will shut down by clicking “OK” button. Then disconnect
the power.
6. Login
First connect the camera to the DVR. Then go to Start → Settings → Camera
→ Manage Camera → Camera Signal to set the signal mode of camera. The
actual signals input shall correspond to the video mode. Please refer to User
Manual for details.
④ Go to Start → Settings → Camera → Add Camera. The DVR will automatically
refresh the list of online IP cameras which are in the same local network with
the DVR. Click to modify the IP address.
Username
Password
Pattern Lock
Confirm Password
admin
Edit
Wizard
123456
123456
Display Password
Enable
Log In Automatically
NextEdit ecurity uestion S QCancel
4.0.0.1. bet a1
Version
80
No. Addres s Edi tPort Proto col M odel
Subnet Mas k
1
192.168. 2.4 5
XXXXXX
255.255.255.0
Quickly Add Manually Add
Add Camera
Selected: 1/1
Add
Default Pa ssw ord
Remain Bandwidth: 10 / 10 Mb Canc el
Mac Address
Address
Edit IP
192 .16 8 . 1 . 45
255 . 255 . 255 . 0
admin
192 .16 8 . 1 . 1
Subnet Mas k
Username
Gateway
Password
OK Cancel
CE :98 :23 :75 : 35 :22
3. HDD Installation
2. Packing Check
This series of the product supports 8 SATA hard drives. The pictures of the
installation are only for reference, please take the real object as the standard. Please
make sure that the device is powered off before the installation.
① Remove the cover and loosen the screws to take out two mounting bars.
② Fix the HDDs on the mounting bar with screws.
Please check the device and accessories after getting the device. If there are
any damages, shortages or defects, please contact your dealer immediately.
③ Install the two mounting bars with HDDs back to the device ( It is recommended to
install the copper-pillar provided in case the HDDs are damaged by external forces ).
④ Connect the power and data cables.
⑤ Install back the cover and secure it with the screws.
Tips: Please check the inside structure of the device and make sure the cables connected
well before installing the cover back.
AUDIO IN Connectors for audio input
VIDEO IN
AUDIO OUT
MIC IN
CVBS
LAN1/2
VGA
HDMI1
HDMI2
USB3.0/USB
RS 485 K/B: connector for a keyboard. A is TX+; B is TX-
P/Z: connector for a PTZ device. Y is TX+; Z is TX-
ALARM OUT
ALARM IN
E-SATA
RJ 45 1000Mbps Ethernet ports
Connectors for video input
Connectors for audio output
Connect to a microphone used for two-way talk
CVBS video output connector
Connect to monitor
Connect to monitor, used as main output
Connect to monitor, used as secondary output
Connect to USB storage device or USB mouse
Connector for alarm output devices
Connector for alarm input devices, like sensors
Connect to the HDD with e-SATA interface
►LAN
① Set the network of the DVR. Go to Start → Settings → Network →TCP/IP. Enter
IP address, subnet mask, gateway, etc. If using DHCP, please enable DHCP in both the
NVR and the router.
② Go to Start → Settings → Network → Port. Enter HTTP port (the default value
is 80), server port (the default port is 6036).
③ Click “Apply” to save the settings.
Network Fault Tolerance: Bound two network ports to one IP address. This pattern
can increase the network bandwidth and form a network redundant array to share the load.
When one port goes wrong, the other port will take over the entire load immediately and
seamlessly.
Multiple Address Setting: You shall set the IP address, subnet mask, gateway and
DNS of each ethernet port respectively.
The pictures are only for reference, please refer to User Manual for details.
IP Address Settings
Obta in an IPv 4 addre ss automa tical ly
Obta in DNS au tomat icall y
Obta in an IPv 6 addre ss automa tical ly
Ethernet Port 1 ( Online ) Ethernet Port 2 ( Online )
Addr ess
MCA Addr ess
Addr ess
MAC Add ress
192 . 16 8 . 1 . 2
10 . 151 . 1 51 . 1
0 . 0 . 0 . 0
. . .
0
192 . 16 8 . 1 . 1
Netw ork Fau lt Tol erance
Ethe rnet Po rt 1
1500
Subn et Mask
Preferred DNS
Mask L ength
Gate way
Prim ary Car d
Work Pat tern (Mod ifyin g work pa ttern need to rebo ot )Gat eway
Gate way
MTU
After you finish adding IP cameras, you can see the live images through the monitor
of the DVR. The following will mainly introduce how to add the IP cameras via
LAN/WAN. This DVR has two network ports, you can select the network work
pattern as needed. Network fault tolerance and multiple address setting are optional.
Admin Password Setup
