TW Audio FDBSX User manual

Assembly
Instructions
FDBSX

Assembly instructions FDBSX
2
Introduction
Thank you for choosing a high-quality product “MADEIN GERMANY” from TW AUDiO.
The front cover FDBSX is an accessory for the loudspeaker BSX.
It is characterized by a subtle look, a remarkable size to weight ratio and ease of use.
If you lend your product to another party, inform that party of the safety-related operating pro-
cedures and hand over this operating manual. If you require additional copies of this manual,
you can obtain them free of charge from TW AUDiO or download them from: www.twaudio.de
Instructions in this setup manual
Strictly adhere to the instructions contained in this assembly guide that are marked as follows:
This symbol in combination with the signal word „Caution” identifies a potentially hazardous
situation. Failure to comply with this safety instruction can lead to light or moderate injury.
This symbol in combination with the signal word „Note” identifies a potentially hazardous situ-
ation. Failure to comply with this safety instruction can lead to product damage.
This symbol in combination with the signal word „Tip” identifies additional information or notes
that will simplify working with TW AUDiO products on the basis of practical experience.
This symbol in combination with the signal word „Warning” identifies a potentially hazardous
situation. Failure to comply with this safety instruction can lead to serious injury or even death.
NOTE
TIP
CAUTION
WARNING

Assembly instructions FDBSX
3
Notes on the products
Read manual
before use!
Before using the front cover, carefully read the assembly instructions and keep the instructions
in a safe place together with the FDBSX front cover.
General Information
Assembly instructions: OM-FDBSX
Version 1.0 en, 02/2019
© by TW AUDiO 2019; all rights reserved.
All information contained in this assembly guide was correct to the best of our knowledge at
the time of printing.
Quality warranties or assurance of suitability for a certain type of use based on the technical
specifications, dimensions and weights are not granted by TWAUDiO.
TW AUDiO also shall not assume liability for any secondary damage (property damage and/
or personal injury) nor for the failure to comply with this assembly guide!
TW AUDiO reserves the right to update this document based on recent developments.
TW AUDiO GmbH
Osterholzallee 140
71636 Ludwigsburg
Germany
Telefon: + 49 (0) 71 41-48 89 89 0
Telefax: + 49 (0) 71 41-48 89 89 99
E-Mail: [email protected]
WWW: www.twaudio.de

Assembly instructions FDBSX
4
Content
1. Safety | Intended use...................................................................................................... 5
2. Overview ........................................................................................................................ 6
2.1 Components ........................................................................................................... 6
3. Technical specifications .................................................................................................. 6
3.1 Data sheet............................................................................................................... 6
4. Commissioning............................................................................................................... 7
4.1 Setup ..................................................................................................................... 7
5. Transport and Storage.................................................................................................... 8
6. CE Conformity Declaration.............................................................................................. 8
7. Disposal ......................................................................................................................... 9

Assembly instructions FDBSX
5
1. Safety | Intended use
To avoid risks please observe the following safety instructions when using accessories.
The FDBSX front cover was developed for use in professional sound systems. The front cover
may only be used by trained and qualified personnel.
Note the operating modes described in this operating manual. Other uses are not permis-
sible.
Damage caused by improper use is not covered by TW AUDiO
The front cover FDBSX may only be used with the loudspeaker BSX.
These assembly instructions describe how to use the FDBSX front cover. Any other use shall
be deemed improper and may result in damage or even injury.
Modifications or alterations to individual parts of the FDBSX front cover are not permitted!
WARNING
The FDBSX is an accessory designed both for indoor and outdoor use.
The FDBSX front cover may only be used by trained and qualified personnel. Personnel must
check the FDBSX for its full suitability before each use.
WARNING
When visible damage to any part of the FDBSX front cover is detected, it must be decommis-
sioned immediately.
Before each installation, check the integrity of the FDBSX front cover and ensure that all com-
ponents are in perfect condition.
WARNING
CAUTION
WARNING

Assembly instructions FDBSX
6
2.1 Components
1. front cover - Polyurea-coating
2. Butterfly-Latch, size: medium
Figure 2.1 - Overview
3.1 Data sheet
Dimensions (d x w x h) 1400 x 600 x 30 mm (55,118 x 23,622 x 1,181 in)
Weight 12 kg (26,455 lbs)
Surface Polyurea-coating
2. Overview
3. Technical specifications
1
2
2

Assembly instructions FDBSX
7
4. Commissioning
Figure 4.1 - Transport setup BSX with FDBSX
4.1 Setup
1. Carefully position the FDBSX front cover on the front of the loudspeaker.
2. Attach the front cover FDBSX to the BSX loudspeaker using the butterfly latches.
3. Make sure that the hooks on the butterfly latches are hooked into the BSX speaker’s dolly
panels.
NOTE

Assembly instructions FDBSX
8
5. Transport and Storage
Ensure that the front cover is not damaged during transport and storage. Moisture can pene-
trate exposed wood surfaces and cause the wood to swell.
This is why the product should be transported and stored in a safe, careful, dry and largely
dust-free manner.
The original packaging is not suitable as permanent storage and transport packaging.
NOTE
Copy and translation of the original CE Conformity Declaration:
We hereby declare that the below-referenced components by virtue of their design and
construction, and in the configuration placed on the market by us, satisfy the safety and
health requirements of the applicable EC directives. This declaration becomes invalid in
case of modifications that have not been approved by us.
This declaration applies to the following components
• FDBSX
as well as all model variants based on these, provided that they correspond to the original
factory models and have not been technically modified in any way.
Applicable directives:
• 2001/95/EG
Applicable national standards and technical specifications:
• DIN EN ISO 12 100
• DGUV Vorschrift 17 und 18
Ludwigburg, Germany, Mai 1st, 2010
Tobias Wüstner
6. CE Conformity Declaration

Assembly instructions FDBSX
9
7. Disposal
If you have any question regarding the disposal of used devices, please contact us under the
following telephone number:
+49 (0) 71 41 - 48 89 89 0
In countries outside of the European Union, comply with local regulations.

Assembly instructions FDBSX
10
TW AUDiO GmbH
Osterholzallee 140
71636 Ludwigsburg
Germany
Phone : + 49 (0) 71 41-48 89 89 0
Fax: + 49 (0) 71 41-48 89 89 99
E-Mail: [email protected]
WWW: www.twaudio.de