Twin-Star International Bell'O 26MM9313 User manual

1
ATTENTION
IF YOU HAVE ANY PROBLEMS OR QUESTIONS, EMAIL
OR CALL CUSTOMER SERVICE BEFORE YOU RETURN
THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED.
For Customer Service: www.twinstarhome.com
in English Call: 866-661-1218
in Spanish Call: 866-661-1218
in French Call: 866-374-9203
ATENCIÓN
SI TIENE ALGÚN PROBLEMA O PREGUNTAS,
ENVÍE UN MENSAJE DE CORREO ELECTRÓNICO O LLAME AL SERVICIO
DE ATENCIÓN AL CLIENTE ANTES DE DEVOLVER
ESTE PRODUCTO A LA TIENDA EN LA QUE LO COMPRÓ.
Servicio de atención al cliente: www.twinstarhome.com
Línea para llamadas en inglés: 866-661-1218
Línea para llamadas en español: 866-661-1218
Línea para llamadas en francés: 866-374-9203
STOP STOP
PARE PARE
ATTENTION
SI VOUS AVEZ DES PROBLÈMES OU QUESTIONS,
ENVOYEZ UN COURRIEL AU SERVICE À LA CLIENTÈLE OU APPELEZ LE
SERVICE À LA CLIENTÈLE AVANT DE RETOURNER
CE PRODUIT OÙ VOUS L’AVEZ ACHETÉ.
Pour le service à la clientèle : www.twinstarhome.com
pour le service en anglais, composez le 866-661-1218
pour le service en espagnol, composez le 866-661-1218
pour le service en français, composez le 866-374-9203
ARRÊT ARRÊT
INSTRUCTION MANUAL ENCLOSED
MANUEL D’INSTRUCTION À L’INTÉRIEUR
MANUAL DE INSTRUCCIONES ADJUNTO
INSTRUCTION MANUAL ENCLOSED
MANUEL D’INSTRUCTION À L’INTÉRIEUR
MANUAL DE INSTRUCCIONES ADJUNTO

1
MEDIA CABINET
26MM9313
INSTRUCTION MANUAL
Twin-Star International, Inc.
Delray Beach, FL 33445
Made in China
Printed in China
Français p. 15
MAXIMUM LOAD 30 lb. (13.6kg)
CAUTION: This unit is intended for use only with the products and maximum weights
indicated. Use with other products or products heavier than the maximum weights
indicated may result in instability causing possible injury.
Note: Flat Panel TVs with base support should be placed squarely in the center of the
stand with no overhang on any side.
FIT UP TO 45” PLASMA/LCD TELEVISIONS
MAXIMUM LOAD 100 lb. (45.35 kg)
Español p. 8
www.twinstarhome.com
In English call: 866-661-1218
In French call: 866-374-9203
In Spanish call: 866-661-1218
For Customer Service:

2
Part Description Quantity
A Front Frame 1
B Back Frame 1
C Center Left Panel 1
D Center Right Panel 1
E Left Side Panel 1
F Right Side Panel 1
G Glass Top 1
H Glass Shelf 2
I Left Base Panel 1
J Right Base Panel 1
K Article Support 2
L Angle Iron 2
M Triangle iron 8
N Feet 2
HARDWARE CONTENTS
Part Description
Bolt
1/4 in. x 1 in.
Bolt
1/4 in. x 1/2 in.(black)
Bolt
1/4 in. x 1/2 in.(white)
Plastic Bumper
Magnet
Bolt
5/32 in. x 1/4 in.
4
4
3
16
2
4
Quantity Picture
(Shown to size)
BB
CC
EE
DD
FF
GG
AA
2
Connection iron

3
Allen Key 1
KK
SAFETY INFORMATION
WARNING
• Before assembly, carefully use scissors or utility knife to cut and unwrap all parts.
Make sure you do not discard the hardware.
CAUTION
• Use care in assembling your new fireplace. Take your time and use the hardware
provided and a quality Phillips head screwdriver. Never overtighten bolts.
• Do not sit on any part of the mantel.
• All panels are labeled left and right as viewed from the front of unit.
Screw M4x37mm 1
JJ
HH
II
Anchor
Tipping Restraint
1
1
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and diagram above. If any part is missing or damaged, do not attempt to
assemble, install or operate the product. Contact customer service for replacement parts.
Estimated Assembly Time: 60 Minutes
Tools Required for Assembly (not included): Phillips head screwdriver, scissors and utility knife

4
Fig. 2
Hardware Used
Hardware Used
AA
BB
x 4
x 4
x 1
x 1
Bolt
1/4 in. x 1 in.
Bolt
1/4 in. x 1/2 in.(black)
3.Locate Back Frame (B) on the Completed
Assembly from step 2, using Bolt (AA) through the
pre-drilled holes in the frame and tighten.
ASSEMBLY INSTRUCTIONS
Fig. 1
N
C
D
F
E
BB
D
C
1. Turn in the Feet (N) into the hole of Center Left
Panel (C) and Center Right Panel (D) and tighten.
2. Insert Center Left Panel (C) and Center Right Panel
(D) into the holes of Front Frame (A).
Attached Left Side Panel (E) and Right Side Panel
(F) to Front Frame (A), using Bolt (BB) through the
pre-drilled holes in the Front Frame (A) and tighten.
Fig. 3
B
A
AA
KK
KK
Allen Key
Allen Key

5
Fig. 6
Fig. 4
Fig. 5
PUT DOWN
PUT DOWN
Hardware Used
DD
DD
FF
J
I
x 4
x 2
Bolt
5/32 in. x 1/4 in.
M
M
FF Magnet
4.Lay Completed Assembly stand on the bottom, put
down Connection Iron (M) to the corner and connect
Center Left Panel (C) , Center Right Panel (D), Front
Frame (A) and Back Frame (B).
5.Attach Magnet (FF) to the Front Frame (A), using
Bolt (DD) through the pre-drilled holes and tighten.
6.Put Left Base Panel (I) and Right Base Panel (J) on
the bottom of Completed Assembly from step 5.

6
Fig. 9
G
Fig. 7
Fig. 8
H
H
KKEE
Hardware Used
EE x 16
Plastic Bumper
7.Lay Article Supports (K) in the middle of Bottom,
and push the Article Supports (K) into the holes. Put
the Plastic Bumpers (EE) on the shelf pins.
8.Allow Glass Shelves (H) to rest on the Plastic
Bumpers (EE).
9.Lift Glass Top (G) and allow the Glass Top to rest on
the top of Completed Assembly from step 8.

7
Fig. 10
Fig. 11
CC
L
GG
CC
Hardware Used
KK Allen Key
10. Attach Angel Iron (L) to Article Supports (K), using
Bolt (CC) through the pre-drilled hole in Article
Supports (K) and tighten.
11. Attach the Connection Iron (GG) to the hole of Back
Frame (B), then tighten the Screw (CC) through the
pre-drilled hole.
Hardware Used
CC
CC
GG
x 2
x 1
x 1
Bolt
1/4 in. x 1/2 in.(white)
Bolt
1/4 in. x 1/2 in.(white)
Connection iron

8
Fig. 12
II
HH GG JJ
Hardware Used
GG
HH
II
JJ
x 1
x 1
x 1
x 1
Anchor
Connection iron
Tipping Restraint
Screw
12. Decide on the location of the cabinet. Drill one hole
into wall with power drill, Push Anchors (HH) into
wall holes. Using a Phillips screwdriver, turn screws
(JJ) with Connection iron (GG) into Anchors (HH).
We have included one Tipping Restraint (II) for
this unit. You must connect this one to prevent
accidents or injuries. When properly connected,
this Tipping Restraint (II) can provide protection
against unexpected tipping of the Unit due to small
tremors, bumps or climbing. We strongly recom
mend mounting this Tipping Restraint (II) to a wall
stud and your Unit.
Warning: You must connect the Anti-rewind to
help prevent any accidents or damage
to the unit.

9
GABINETE PARA MEDIOS
26MM9313
INSTRUCCIÓN DE MONTAJE
Français p. 19
English p. 1
PRECAUCIÓN: Esta unidad está diseñada para ser usada únicamente con los
productos y con los pesos máximos indicados. El uso con otros productos, o con
productos de peso mayor a los pesos máximos indicados, puede producir inestabilidad,
lo que posiblemente causaría lesiones.
Note: Los televisores de pantalla plana con soporte de base deben colocarse
perfectamente en el centro de la base del gabinete, sin que ninguno de los laterales
sobresalga.
www.twinstarhome.com
Línea para llamadas en inglés: 866-661-1218
Línea para llamadas en francés: 866-374-9203
Línea para llamadas en español: 866-661-1218
Servicio de atención al cliente:
Twin-Star International, Inc.
Delray Beach, FL 33445
Fabricado en China
Impreso en China
CARGA MÁXIMA 30 lb. (13,6kg).
ENCAJA TELEVISIONES DE
PLASMA/LCD HASTA 45", CARGA
MÁXIMA 100 lb. (45.35kg)