Ty Pennington Style D71 M34473 User manual

Date of purchase: _____/ _____/ _____
SUNSET BEACH HARDTOP BAR WITH GRANITE AND 2 STOOLS
Product Code: D71 M34473
UPC Code: 749241314360
1

2
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or
install the product. If any parts is missing or damaged, do not attempt to assemble the product.
Two to four people are needed for assembly.
Load capacity of the chair: 400 lbs. (max)
In order to avoid damage to the shelter and its components, use appropriate tools. Do not use the
structure as a support.
Check all screws on a regular basis to maintain the solidity of the structure.
Keep instructions and parts list for further use.
Estimated Assembly Time: Approx. 2 - 3 hours
CAUTION
Do NOT tighten all parts before assembly is complete.
Do NOT overtighten any of the bolts as this may damage the threads. Tighten each bolt firmly and
properly.
Do NOT sit or stand on the table.
Do NOT use power tools to assemble this product.
Rpeated assembly can weaken the locking ability of the washers. Periodically check all bolted
connections on your furniture to make sure they are tight and secure. Retain these instructions for
future reference.
Some parts may contain sharp edges. Wear protective gloves as necessary.
Always place the cushions on seat frame of the chair to aviod damage to the piece.
This outdoor furniture is designed and made for personal, non-commercial use. It should not be used
as a toy or a tool. Children under age of 16 should not be engaged in assembly, removal or
disassembly. Children under age of 10 should be supervised by a competent adult while using this
furniture. Small parts like bolt screws may pose a choking hazard to young children. Keep out of reach
of small children.
WARRANTY
1 year limited warranty.
Limited warranty applicable on parts only. Warranty extends solely to the original purchaser, who
must offer the original sales receipt for record.
EXCLUDED
Damages due to vandalism, abuse and wrong use of the product is not covered by the warranty.
Damages due to extreme weather conditions such as thunderstorm and windstorm.
MAINTENANCE
If this furniture needs repairs, DO NOT RETURN THE PRODUCT TO SEARS.
In case of a defective part of if a problem occurs while using this Product, please contact Bond Vast
at 1-800-961-9838, 9AM ~ 5PM, Pacific Time Zone, Monday - Friday.
Or email us: [email protected].
NOTICE
THIS ARTICLE DOES NOT MEET CALIFORNIA BUREAU OF HOME FURNISHING’S
FLAMMABILITY REQUIREMENTS TECHNICAL BULLETIN 117. CARE SHOULD BE EXERCISED
NEAR OPEN FLAME OR WITH BURNING CIGARETTES.

A
C
E
F
I
D
G
J
B
H
O
KM
L
N
P
Q
R
S
T
U
W
YZ
AB
AC
X
V
3

AD
AE
AF
AG
AI
AH
4

M 1
A4
B
C
D
E
F
G
H
I
J
K
L 1
1
1
1
1
1
1
1
2
1
1
5
Part No. Description Qty IIIustration
Base Post
Back Panel
Side Panel 1
Side Panel 2
Support Leg 1
Support Leg 2
Shelving 1
Shelving 2
Shelving 3
Support Tube
Granite Tabletop 1
Granite Tabletop 2
Granite Tabletop 3

N
O
P
Q
R
S
4
4
2
2
1
1
T4
U 2
V 2
W 2
X 2
Y 2
Z2
6
Part No. Description Qty IIIustration
Plastip Loop
Upper Post
Short Crossbar
Long Crossbar
Roof Connector
Roof Cap
Long Roof Tube
Short Roof Tube 1
Short Roof Tube 2
Roof Panel 1
Roof Panel 2
Roof Panel 3
Roof Panel 4

7
AB 4
AC 4
Part No. Description Qty IIIustration
Corner Connector
Center Connector
AE 2
AF 2
Left Armrest
Right Armrest
AH 2
AI 2
Cushion
Connector Bracket
AD 2
Seat Frame
AG 2
Backrest

8
AA 73
BB 24
3CC
16
4
DD
7
EE
1
FF
2
GG
1
HH
II
Part No. Description Qty IIIustration
4
JJ
Screw 1 M6 x 15mm
Screw 2 M6 x 25mm
Screw 3 M6 x 30mm
Screw 4 M6 x 35mm
Screw 5 M6 x 45mm
Screw 6 M6 x 55mm
Bolt Nut
Washer
Allen Wrench
Spanner

x 2
B
B
B
1
CC
FF
9
1. Secure both back panel (B) by using screw 3 (CC) and bolt nut (FF) as figure 1 shown.
B
B
1
1
1
此改為：GG
此處改為：GG

Ax 2
B
B
A
A
1
1
A
1
B
BB
1
1
1
1
10
1. Insert screw 2 (BB) through back panel (BB) secure with base post (A) as figure 1 shown.
Repeat for remaining base post (A).

Ax 2
Ex 1
Fx 1
A
A
F
E
1
1
AA
A
E
11
11
1
1
1. Insert screw 1 (AA) through support leg 1 (E), secure with base post (A) as figure 1 shown.
Repeat for remaining base post (A) and support leg 2 (F).
1

Cx 1
Dx 1
A
C
D
A
1
1
C
A
1BB
1
1
1
1
1
1
1
1
1. Insert screw 2 (BB) through side panel 1 (C), secure with base leg (A) as figure 1 shown.
Repeat for side panel 2 (D).
12

Gx 1
B
B
G
1
1
G
B
AA
13
11
1. Insert screw 1 (AA) through shelving 1 (G), secure with back panel (B) as figure 1 shown.

I
x 1
H
x 1
H
I
D
C
G
I
GD
1
1
AA
1
B
B
14
1. Insert screw 1 (AA) into shelving 3 (I), secure with side panel 2 (D) as figure 1 shown. Then insert
screw 1 (AA) into shelving 2 (H), secure with side panel 1 (C).

G
I
E
F
C
D
BB
1
1
2
2
2
1
G
II
F
AA
GG
AA
15
1. Connect shelving 1( G) with shelving 3 (I) by using screw 1 (AA) and bolt nut (GG) as figure 1 shown.
Then connect shelving 3 (I) with support leg 2 (F) by using screw 1 (AA).
Repeat this step for shelving 2 (H) on the other side.

Jx 1
J
C
D
11
JD
1
AA
16
1. Insert screw 1 (AA) through support tube (J), secrue with side panel 2 (DD) as figure 1 shown.
Then insert screw 1 (AA) through the other side of support tube (J), secure with side panel 1 (CC).

x 1
M
M
J
B
B
17
1. Insert screw 2 (BB) through back panel (B) secure with granite tabletop 3 (M), then insert
screw 5 (EE) through support tube (J) secure with granite tabletop 3 (M) as figure 1 shown.
EE
M
J
B
BBB BB
EE
1

Kx 1
M
K
C
BB
D
J
1
2
E
F
18
1. Insert screw 2 (BB) through side panel 1 (C), secure with granite tabletop 1 (K), then insert screw 5
(EE) through support tube (J), secure with granite tabletop 1 (K) as figure 1 shown.
2. Insert screw 1 (AA) through support leg 1 (E), secure with granite tabletop 1 (K) as figure 1 shown.
K
C
J
E
EE
BB
BB
AA
1

L
x 1
M
J
D
F
E
C
BB
K
1
2
L
1. Insert screw 2 (BB) through side panel 2 (D), secure with granite tabletop 2 (L), then insert screw 5
(EE) through support tube (J), secure with granite tabletop 2 (L) as figure 1 shown.
2. Insert screw 1 (AA) through support leg 2 (F), secure with granite tabletop 2 (L) as figure 1 shown.
19
L
D
F
J
EE
BB
BB AA
1

Ox 4
Nx 4
O
N
A
11
1
1
O
A
1
AA
1. Insert upper post (O) through plastic loop (N) into base post (A), and use screw 1 (AA) to secure
base post (A) with upper post (O).
Repeat for remaining upper post (O).
20