TYAN Tomcat i925X S5130 User manual

Tomcat i925X S5130 User’s Manual
i
http://www.tyan.com
Tomcat i925X /// S5130
Revision 1.00
Copyright © TYAN Computer Corporation, 2004. All rights reserved. No part of this manual
may be reproduced or translated without prior written consent from TYAN Computer Corp.
All registered and unregistered trademarks and company names contained in this manual are
property of their respective owners including, but not limited to the following.
TYAN, Tomcat, i925X and S5130 are trademarks of TYAN Computer Corporation.
Intel Prescott and combinations thereof are trademarks of Intel Corporation.
Promise is a trademark of Promise Technology, Inc.
Award, AwardBIOS are trademarks of Award Software Incorporated.
Microsoft and Windows are trademarks of Microsoft Corporation.
IBM, PC, AT and PS/2 are trademarks of IBM Corporation.
VIA is a trademark of VIA Technologies, Inc.
Winbond is a trademark of Winbond Electronics Corporation.
SMSC is a trademark of Standard Microsystems Corporation.
Realtek is a trademark of Realtek Semiconductor Corporation.
Broadcom is a trademark of Broadcom Corporation.
Portable Document Format (PDF) is a trademark of Adobe Corporation.
Information contained in this document is furnished by TYAN Computer Corporation and has
been reviewed for accuracy and reliability prior to printing. TYAN assumes no liability
whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of
TYAN products including liability or warranties relating to fitness for a particular purpose or
merchantability. TYAN retains the right to make changes to product descriptions and/or
specifications at any time, without notice. In no event will TYAN be held liable for any direct or
indirect, incidental or consequential damage, loss of use, loss of data or other malady resulting
from errors or inaccuracies of information contained in this document.

Tomcat i925X S5130 Table of Contents
ii
http://www.tyan.com
Table of Contents
Before you begin… .................................................................................................................. v
Chapter 1: Introduction.........................................................................................................1-1
1.1 Congratulations! ......................................................................................................... 1-1
1.2 Hardware Specifications ............................................................................................ 1-1
Chapter 2: Board Installation...............................................................................................2-1
2.1 Installing the Motherboard ......................................................................................... 2-1
2.1.1 Installation Notes ............................................................................................. 2-1
2.2 Board Image .............................................................................................................. 2-2
2.3 Block Diagram............................................................................................................ 2-3
2.4 Motherboard Components ......................................................................................... 2-4
2.5 Jumpers and Connectors...........................................................................................2-5
2.5.1 Serial ATA RAID Connectors: J20/J19/J23/J22 (SATA1 & SATA2 & SATA3 &
SATA4)........................................................................................................... 2-6
2.5.2 Serial Port: COM1 (J21) .................................................................................. 2-6
2.5.3 IPMB Connector: J24 (optional)....................................................................... 2-7
2.5.4 Front Fan Connector: J27 (FAN1) ................................................................... 2-7
2.5.5 Audio CD_in Connector: J28 (Optional) .......................................................... 2-8
2.5.6 Front Panel Audio Connector: J29 (Optional)..................................................2-8
2.5.7 IEEE1394a Connector: J30 / J32 (Optional).................................................... 2-9
2.5.8 Chassis Fan Connector: J31 (FAN2)...............................................................2-9
2.5.9 Front Panel USB 2.0 Connector: J34/J36 (USB3/USB4) .............................. 2-10
2.5.10 CPU Fan Connector: J35 (P1FAN).............................................................. 2-10
2.5.11 SMDC Connector: J37 (Optional) ................................................................ 2-11
2.5.12 Front Panel LAN1/LAN2 Link and Active LED Connector: J38/J39 (Optional)...
..................................................................................................................... 2-11
2.5.13 Front Panel System Connector: J40............................................................2-12
2.5.14 Chassis Fan Connector: J42 (FAN3)...........................................................2-12
2.5.15 Chassis Fan Connector: J43/J44 (FAN4/FAN5)..........................................2-13
2.5.16 Front Panel LAN1/LAN2 Speed LED Pin-Header: J45/J46 (Optional) ........ 2-13
2.5.17 Clear CMOS Jumper: JP1 ........................................................................... 2-14
2.6 Mounting the Motherboard.......................................................................................2-15
2.7 Installing Memory..................................................................................................... 2-16
2.7.1 Memory Installation Procedure ...................................................................... 2-17
2.8 Installing the Processor and Cooling Fan ................................................................2-17
2.9 Installing Drive Cables ............................................................................................. 2-20
2.10 Installing Expansion Cards .................................................................................... 2-21
2.11 Connecting External Devices................................................................................. 2-22
2.11.1 Onboard LAN LED Color Definition ............................................................. 2-22
2.12 Installing the Power Supply.................................................................................... 2-23
2.13 Finishing Up ........................................................................................................... 2-23
Chapter 3: BIOS Setup..........................................................................................................3-1
3.1 About the BIOS .......................................................................................................... 3-1
3.1.1 Starting Setup .................................................................................................. 3-1
3.1.2 Setup Basics.................................................................................................... 3-1
3.1.3 Getting Help..................................................................................................... 3-1
3.1.4 In Case of Problems ........................................................................................ 3-2
3.1.5 Setup Variations .............................................................................................. 3-2
3.2 Main BIOS Setup ....................................................................................................... 3-2
3.3 Standard CMOS Features ......................................................................................... 3-4
3.4 Advanced BIOS Features .......................................................................................... 3-5
3.4.1 CPU Features .................................................................................................. 3-7
3.4.2 Boot Sequence .............................................................................................. 3-10

Tomcat i925X S5130 Table of Contents
iii
http://www.tyan.com
3.4.3 Console Redirection ...................................................................................... 3-12
3.5 Advanced Chipsets Features................................................................................... 3-13
3.5.1 PCI Express Root Port Function.................................................................... 3-15
3.6 Integrated Peripherals.............................................................................................. 3-16
3.6.1 OnChip IDE Device........................................................................................ 3-16
3.6.2 Onboard Device ............................................................................................. 3-18
3.6.3 Super IO Device............................................................................................. 3-20
3.7 Power Management Setup ...................................................................................... 3-22
3.7.1 PCI Express PM Function.............................................................................. 3-24
3.7.2 Power On Setup............................................................................................. 3-25
3.7.3 Reload Global Timer Events.......................................................................... 3-26
3.8 PnP/PCI Configurations ........................................................................................... 3-27
3.8.1 IRQ Resources .............................................................................................. 3-28
3.9 PC Health Status ..................................................................................................... 3-29
3.10 Frequency/Voltage Control .................................................................................... 3-30
3.11 Load Fail-Safe Defaults ......................................................................................... 3-31
3.12 Load Optimized Defaults........................................................................................ 3-32
3.13 Supervisor/User Password Setting ........................................................................ 3-32
3.14 Save & Exit Setup .................................................................................................. 3-33
3.15 Exit Without Saving................................................................................................ 3-34
Chapter 4: SATA/RAID Setup (for SATA RAID model) ......................................................4-1
4.1 Configuring BIOS for Intel RAID for Serial ATA on board..........................................4-1
4.1.1 Creating, Deleting, and Resetting RAID Sets .................................................. 4-1
4.1.2 Create RAID 0 or RAID 1 Volume ................................................................... 4-1
4.1.3 Delete RAID Volume........................................................................................ 4-2
4.1.4 Reset RAID Data ............................................................................................. 4-2
4.2 Loading the Intel Application Accelerator RAID Edition Driver During Operating
System Install............................................................................................................ 4-2
4.2.1 Instructions on Creating F6 Floppy Diskette.................................................... 4-3
4.2.2 Installation Using F6 Method ........................................................................... 4-3
4.3 Intel RAID Option ROM.............................................................................................. 4-4
4.3.1 Description ....................................................................................................... 4-4
4.3.2 Confirming Version of Intel RAID Option ROM Installed ................................. 4-4
4.3.3 Using the Intel RAID Option ROM ................................................................... 4-4
4.4 Installing the Intel Application Accelerator RAID Edition.......................................... 4-10
4.4.1 Installation Caution ........................................................................................ 4-10
4.4.2 Steps to Take Before Installing the Intel Application Accelerator RAID Edition....
......................................................................................................................... 4-10
4.4.3 Obtaining and Installing the Intel Application Accelerator RAID Edition ........ 4-10
4.5 Confirming the Intel Application Accelerator RAID Edition is Installed .................... 4-14
4.6 Confirming Version of Intel Application Accelerator RAID Edition Installed.............4-14
4.6.1 Using the Intel Application Accelerator RAID Edition Utility:.......................... 4-15
4.6.2 RAID Driver File Properties: .......................................................................... 4-15
4.7 Issues During Installation......................................................................................... 4-15
4.7.1 Symptom: Incompatible Hardware................................................................. 4-15
4.7.2 Symptom: Unable to launch Intel(R ) Application Accelerator Readme file... 4-15
4.8 “RAID Ready”........................................................................................................... 4-16
4.8.1 “RAID Ready” Definition ................................................................................ 4-16
4.8.2 “RAID Ready” System Requirements ............................................................ 4-16
4.8.3 Steps on Setting Up a “RAID Ready” System ...............................................4-16
4.8.4 Converting a “RAID Ready” System into RAID 0 or RAID 1 System with
Migration Feature ......................................................................................... 4-16
4.9 RAID Migration Instructions ..................................................................................... 4-17
4.9.1 Create RAID Volume from Existing Hard Drive ............................................. 4-18

Tomcat i925X S5130 Table of Contents
iv
http://www.tyan.com
4.9.2 Migration Process May Take Considerable Time to Complete...................... 4-21
4.10 Uninstalling the Intel Application Accelerator RAID Edition ................................... 4-22
4.10.1 Uninstall Warning......................................................................................... 4-22
4.10.2 Windows* XP / Windows 2000 .................................................................... 4-22
4.11 Unattended Installation Under Windows* XP / Windows 2000 .............................. 4-23
4.12 Intel Storage Utility................................................................................................. 4-23
4.12.1 Description ................................................................................................... 4-23
4.12.2 Create Volume Manually ............................................................................. 4-24
4.12.3 Successful Creation..................................................................................... 4-27
Chapter 5: Diagnostics.........................................................................................................5-1
5.1 Beep Codes ............................................................................................................... 5-1
5.2 Flash Utility................................................................................................................. 5-1
Appendix I: Glossary ............................................................................................................6-1
Appendix II: Post Error Code for BIOS ...............................................................................6-7
Technical Support .......................................................................................................... 6-12

Tomcat i925X S5130 Before you begin…
v
http://www.tyan.com
Before you begin…
Check the package contents before you proceed.
The retail motherboard package should contain the following:
1 x Tomcat i925X S5130 motherboard
1 x 34-Pin floppy drive cable
1 x Ultra-DMA-133/100/66/33 IDE cable
1 x Tomcat i925X S5130 User’s Manual
1 x Tomcat i925X S5130 Quick Reference Guide
1 x TYAN driver CD
1 x Intel 82801FR (ICH6R) Driver Diskette
1 x I/O shield
1 x Serial Port cable
1 x IEEE1394a (FireWire) cable (only for models with FireWire)
2 x Serial ATA power cable
4 x Serial ATA cable
1 x USB2.0 cable
If any of these items are missing, please contact your vendor or dealer for replacement before
continuing with the installation process.

Tomcat i925X S5130 Chapter 1: Introduction
1-1
http://www.tyan.com
Chapter 1: Introduction
1.1 Congratulations!
Congratulations on your purchase of the TYAN Tomcat i925X S5130, one of the most
powerful and versatile motherboard solutions available for Intel Prescott processors. Based on
the acclaimed Intel i925X GMCH chipset, the S5130 offers exceptional performance and
outstanding features. With the x16/x1 PCI Express slots, onboard Gigabit Ethernet port, Serial
ATA RAID, four Dual-channel DDR2 DIMM sockets, plus the optional 7.1-channel Audio,
FireWire and Integrated ATI graphics, the Tomecat i925X S5130 is fast and flexible enough to
fit your server/workstation needs.
For more information about this and other TYAN products, visit the TYAN Web site at
http://www.tyan.com. Product FAQs, a list of distributors and advanced BIOS information are
also available on the Web site.
1.2 Hardware Specifications
Processors
ySingle Socket-T (LGA775 socket)
yIntel“Prescott” processor with EM64T
support
y800/533MHz FSB support
Expansion Slots
yOne x16 PCI Express connector for
graphics
yTwo x1 PCI Express connectors
yFour 32-bit, 33MHz PCI v2.3 slots
yTotal seven usable expansion slots
Chipset
yIntel i925X GMCH
yIntel ICH6R South Bridge
ySMSC DME1737
System Management
ySMSC DME1737 w/ hardware monitoring
yOne 3+1-pin CPU Fan header w/
tachometer input and temperature-sensing
auto fan control
yFive 3-pin system Fan headers (3 w/
tachometer input and 4 w/ temperature-
sensing auto fan control)
yTemperature and voltage monitoring
yWatchdog timer
yPort 80 code display LED
Memory
yDual memory channels
ySupports Up to four DDR2-533/400 DIMM
yUp to 4GB of Unbuffered, ECC memory
Integrated I/O Interface
yOne floppy connector
yFour USB 2.0 ports (via cable)
yOne COM port (via cable)
yTYAN 2 x 9 front-panel pin header
Integrated LAN Controllers
yTwo GbE LAN controllers (one is
optional)
―Broadcom BCM5721 GbE LAN
controller
―Operating at x1 PCI-E interface
―ASF 2.0 support
―Pin headers for front panel LAN
LED
Integrated Audio (optional)
yRealtek ALC880 7.1 channel audio
CODEC
y“Azalia”/AC’97 2.3 supported, UAA
compliant
ySupports S/PDIF In/Out interface
y2x5 pin header for front panel audio
connector
yCD-in connector
Integrated PCI IEEE1394a Controller
(optional)
yVIA VT6307 PCI FireWire (1394a)
controller
yTwo IEEE1394a ports (via cable)

Tomcat i925X S5130 Chapter 1: Introduction
1-2
http://www.tyan.com
Intelligent PCI IDE (ICH6R)
ySingle channel master mode supports two
IDE devices
ySupport for ATA-100/66/33 IDE drives and
ATAPI compliant devices
Integrated Serial ATA (ICH6R)
yFour Serial ATA Host controllers embedded
ySupport four Serial ports running at 1.5Gb/s
yRAID 0, 1 support
ySATA activity LED connector
Integrated PCI Graphic (optional)
yATIRageTM XL PCI graphics controller
y8MB Frame Buffer of video memory
Rear Panel I/O ports
yStacked PS/2 Mouse & Keyboard ports
yS/PDIF In/Out optical jacks (optional)
yOne 15-pin VGA port (optional)
yOne 25-pin SPP/ECP/EPP parallel port
ySix audio jacks (optional)
yStacked two USB2.0 ports and one RJ45
100/10/1000 Base-T port w/ activity LED
yStacked two USB2.0 ports and one optional
RJ45 10/100/1000 Base-T port w/ activity
LED
BIOS
yAward BIOS 8Mbit Flash ROM
ySupport APM 1.2 & ACPI 1.0B
yPnP, DNI 2.0, WFM 2.0 Power
Management
Power
yATX12V support, on board 4-phase
VRM
yUniversal 24-pin + 8-pin power
connectors
y4-pin auxiliary power connector
Form Factor
yATX footprint
y12” x 9.6” (305mm x 245mm)
Regulatory
yFCC Class B (Declaration of
Conformity)
yCE (Declaration of Conformity)
yBSMI
Note
TYAN reserves the right to add support or discontinue support for any OS
with or without notice.

Tomcat i925X S5130 Chapter 2: Board Installation
2-1
http://www.tyan.com
Chapter 2: Board Installation
2.1 Installing the Motherboard
The Tomcat i925X S5130 motherboard conforms fully to the ATX specification. Before
continuing with the installation, confirm that your chassis supports a standard ATX
motherboard. If you are unsure, contact your dealer for more information.
2.1.1 Installation Notes
This user manual contains important information and you should read it thoroughly before
attempting the installation procedure.
Precautions:
•Static electricity can damage components on your motherboard. Before touching the
product, discharge any static build up in yourself by touching a well grounded object such
as a metal water pipe or a grounded electrical appliance. TYAN recommends putting on a
good quality grounded wrist strap before removing your motherboard from the antistatic
bag.
•Disconnect your computer from the power supply before any disassembly procedure is
attempted.
•Touch the motherboard as little as possible and do not touch the bottom of the board at all.
Bending or flexing the motherboard may break delicate components or copper tracks on
the board.
•Avoid touching any of the motherboard components.
•Place the motherboard on a grounded antistatic surface or on the antistatic bag in which
the board was shipped.
•Inspect the board for damage.
Read the following sections for detailed instructions on how to install your motherboard in a
chassis and add a processor, memory, and disk drives.
Warning
Do not apply power to the board if it appears damaged.

Tomcat i925X S5130 Chapter 2: Board Installation
2-2
http://www.tyan.com
2.2 Board Image
The following is an image of the Tomcat i925X S5130.
The above photograph is purely representative. Due to engineering updates and new
board revisions, certain components may change and or be repositioned. The picture
above may or may not look exactly like the board you received.
The following page includes details on the vital components of this motherboard.

Tomcat i925X S5130 Chapter 2: Board Installation
2-3
http://www.tyan.com
2.3 Block Diagram
The following is a block diagram of the Tomcat i925X S5130.

Tomcat i925X S5130 Chapter 2: Board Installation
2-4
http://www.tyan.com
2.4 Motherboard Components
The diagram below shows the main motherboard components.
USB3
1
1
1
1
J2
(KB+Mouse)
J5
J3 (VGA) J8
(Parallel Port)
J42
PW3
J7
(LAN2+
USB2)
J1
(Audio)
ALC880
P1FAN
J35
BIOS
J31
Intel
i925X
Intel
ICH6R
32-bit 33MHz (5V) PCI PCI2
32-bit 33MHz (5V) PCI PCI3
32-bit 33MHz (5V) PCI PCI4
PCI-E2
SATA2
SATA1
FDD J26
JP2
RAID P-IDE J33 (Optional) P-IDE J18
1
x16 PCI Express PCI-E1
SUPER
I/O
BT1
PCI-E3 USB4
1
VIA
V
T6307
LED16
32-bit 33MHz (5V)PCI PCI1
SATA3
SATA4
FAN2
Promise
PDC20579
(Optional)
J29
1
J28
BROADCOM
LAN
(Optional)
1
J44
J6
(LAN1+
USB1)
J21
COM1
1
JP1
J30 J32
PW2
1
J43
J12
J19 J22
J20 J23
S5130
J4
(SPDIF-IN)
(SPDIF-OUT)
KB(Bottom)
Mouse(Top)
USB (Bottom)
GbE LAN (Top)
USB (Bottom)
GbE LAN (Top)Optional
J17
J34 J36
BROADCOM
LAN
(Optional)
ATI
Rage XL
J46
1
J45
1
1
SMDC J37
J39
1
1
J38
1
J27
FAN1
J41
(Optional)
This diagram represents the latest version of the motherboard available at the time of
publishing. The board you receive may or may not look exactly like the above diagram.
Parts are not drawn to scale.

Tomcat i925X S5130 Chapter 2: Board Installation
2-5
http://www.tyan.com
2.5 Jumpers and Connectors
Jumpers and pin headers are provided on your motherboard for configuration and connection
to peripherals. The following section shows you how to set your jumpers and use your pin
headers.
Connector Function Ref. Page
J19/J20/J22/J23 Serial ATA Connectors Page 2-6
J21 (COM1) COM1 Port Page 2-6
J24* IPMB Connector (optional) Page 2-7
J25** Reserved
J26 Floppy Disk Drive Connector
J27 (FAN1) Front Fan Connector with tachometer input and
fan speed control Page 2-7
J28* Audio CD-in Connector (optional) Page 2-8
J29* Front Panel Audio Connector (optional) Page 2-8
J30/J32* IEEE1394a Connector (optional) Page 2-9
J31 (FAN2) Chassis Fan Connector Page 2-9
J34/J36
(USB3/USB4) Front Panel USB Connector Page 2-10
J35 (P1FAN) CPU Fan Connector with tachometer input and
fan speed control Page 2-10
J37* SMDC Connector (optional) Page 2-11
J38/J39* Front Panel LAN1/LAN2 Link/Activity LED
Connector (optional) Page 2-11
J40 Front Panel System Connector Page 2-12
J41** Reserved
J42 (FAN3) Chassis Fan Connector with fan speed control Page 2-12
J43/J44 (FAN4/FAN5) Chassis Fan Connector with tachometer input
and fan speed control Page 2-13
J45/J46* Front Panel LAN1/LAN2 Speed LED Connector Page 2-13
JP1 Clear CMOS Jumper Page 2-14
JP2** Reserved
* Some jumpers and headers are optional and not available with the board due to the different
configurations.
** J25, J41 and JP2 are reserved for OEM use only.
Jumper Legend
Jumper OFF – open (without jumper cap)
Jumper ON – closed (with jumper cap)

Tomcat i925X S5130 Chapter 2: Board Installation
2-6
http://www.tyan.com
2.5.1 Serial ATA RAID Connectors: J20/J19/J23/J22 (SATA1 & SATA2 & SATA3 & SATA4)
1 7
Pin 1 2 3 4 5 6 7
Signal GND TXP TXN GND RXN RXP GND
USB3
1
1
1
1
J2
(KB+Mouse)
J5
J3 (VGA) J8
(Parallel Port)
J42
PW3
J7
(LAN2+
USB2)
J1
(Audio)
ALC880
P1FAN
J35
BIOS
J31
Intel
i925X
Intel
ICH6R
32-bit 33MHz (5V) PCI PCI2
32-bit 33MHz (5V) PCI PCI3
32-bit 33MHz (5V) PCI PCI4
PCI-E2
SATA2
SATA1
FDD J26
JP2
RAID P-IDE J33 (Optional) P-IDE J18
1
x16 PCI Express PCI-E1
SUPER
I/O
BT1
PCI-E3 USB4
1
VIA
VT6307
LED16
32-bit 33MHz (5V)PCI PCI1
SATA3
SATA4
FAN2
Promise
PDC20579
(Optional)
J29
1
J28
BROADCOM
LAN
(Optional)
1
J44
J6
(LAN1+
USB1)
J21
COM1
1
JP1
J30 J32
PW2
1
J43
J12
J19 J22
J20 J23
S5130
J4
(SPDIF-IN)
(SPDIF-OUT)
KB(Bottom)
Mouse(Top)
USB (Bottom)
GbE LAN (Top)
USB (Bottom)
GbE LAN (Top)Optional
J17
J34 J36
BROADCOM
LAN
(Optional)
ATI
Rage XL
J46
1
J45
1
1
SMDC J37
J39
1
1
J38
1
J27
FAN1
J41
(Optional)
Connects to the Serial ATA ready drives
via the Serial ATA cable
You may use any two of the four Serial
ATA ports to have the support of RAID 0
and 1 through the on board ICH6R south
bridge chip.
2.5.2 Serial Port: COM1 (J21)
1 9
2 10
Signal Description DSR (Data-Set-Ready) RTS (Request-to-Send) CTS (Clear-to-Send) RI (Ring-Indicator) NC/Key
Pin# 2 4 6 8
10
Pin# 1 3 5 7 9
USB3
1
1
1
1
J2
(KB+Mouse)
J5
J3 (VGA) J8
(Parallel Port)
J42
PW3
J7
(LAN2+
USB2)
J1
(Audio)
ALC880
P1FAN
J35
BIOS
J31
Intel
i925X
Intel
ICH6R
32-bit 33MHz (5V) PCI PCI2
32-bit 33MHz (5V) PCI PCI3
32-bit 33MHz (5V) PCI PCI4
PCI-E2
SATA2
SATA1
FDD J26
JP2
RAID P-IDEJ33 (Optional) P-IDE J18
1
x16 PCI Express PCI-E1
SUPER
I/O
BT1
PCI-E3 USB4
1
VIA
VT6307
LED16
32-bit 33MHz (5V)PCI PCI1
SATA3
SATA4
FAN2
Promise
PDC20579
(Optional)
J29
1
J28
BROADCOM
LAN
(Optional)
1
J44
J6
(LAN1+
USB1)
J21
COM1
1
JP1
J30 J32
PW2
1
J43
J12
J19 J22
J20 J23
S5130
J4
(SPDIF-IN)
(SPDIF-OUT)
KB(Bottom)
Mouse(Top)
USB (Bottom)
GbE LAN (Top)
USB (Bottom)
GbE LAN (Top)Optional
J17
J34 J36
BROADCOM
LAN
(Optional)
ATI
Rage XL
J46
1
J45
1
1
SMDC J37
J39
1
1
J38
1
J27
FAN1
J41
(Optional)
Signal Description
DCD
(Data Carrier Detect)
RX
(Receive-Data)
TX
(Transfer-Data)
DTR
(Data-Terminal-Ready)
GND
(Ground)

Tomcat i925X S5130 Chapter 2: Board Installation
2-7
http://www.tyan.com
2.5.3 IPMB Connector: J24 (optional)
1
Pin_1 Pin_2 Pin_3 Pin_4
IPMB_DATA GND IPMB_CLK NC
USB3
1
1
1
1
J2
(KB+Mouse)
J5
J3 (VGA) J8
(Parallel Port)
J42
PW3
J7
(LAN2+
USB2)
J1
(Audio)
ALC880
P1FAN
J35
BIOS
J31
Intel
i925X
Intel
ICH6R
32-bit 33MHz (5V) PCI PCI2
32-bit 33MHz (5V) PCI PCI3
32-bit 33MHz (5V) PCI PCI4
PCI-E2
SATA2
SATA1
FDD J26
JP2
RAID P-IDEJ33 (Optional) P-IDE J18
1
x16 PCI Express PCI-E1
SUPER
I/O
BT1
PCI-E3 USB4
1
VIA
VT6307
LED16
32-bit 33MHz (5V)PCI PCI1
SATA3
SATA4
FAN2
Promise
PDC20579
(Optional)
J29
1
J28
BROADCOM
LAN
(Optional)
1
J44
J6
(LAN1+
USB1)
J21
COM1
1
JP1
J30 J32
PW2
1
J43
J12
J19 J22
J20 J23
S5130
J4
(SPDIF-IN)
(SPDIF-OUT)
KB(Bottom)
Mouse(Top)
USB (Bottom)
GbE LAN (Top)
USB (Bottom)
GbE LAN (Top)Optional
J17
J34 J36
BROADCOM
LAN
(Optional)
ATI
Rage XL
J46
1
J45
1
1
SMDC J37
J39
1
1
J38
1
J27
FAN1
J41
(Optional)
2.5.4 Front Fan Connector: J27 (FAN1)
+12V
SpeedControl
Tachometer
USB3
1
1
1
1
J2
(KB+Mouse)
J5
J3 (VGA) J8
(Parallel Port)
J42
PW3
J7
(LAN2+
USB2)
J1
(Audio)
ALC880
P1FAN
J35
BIOS
J31
Intel
i925X
Intel
ICH6R
32-bit 33MHz (5V) PCI PCI2
32-bit 33MHz (5V) PCI PCI3
32-bit 33MHz (5V) PCI PCI4
PCI-E2
SATA2
SATA1
FDD J26
JP2
RAID P-IDEJ33 (Optional) P-IDE J18
1
x16 PCI Express PCI-E1
SUPER
I/O
BT1
PCI-E3 USB4
1
VIA
VT6307
LED16
32-bit 33MHz (5V)PCI PCI1
SATA3
SATA4
FAN2
Promise
PDC20579
(Optional)
J29
1
J28
BROADCOM
LAN
(Optional)
1
J44
J6
(LAN1+
USB1)
J21
COM1
1
JP1
J30 J32
PW2
1
J43
J12
J19 J22
J20 J23
S5130
J4
(SPDIF-IN)
(SPDIF-OUT)
KB(Bottom)
Mouse(Top)
USB (Bottom)
GbE LAN (Top)
USB (Bottom)
GbE LAN (Top)Optional
J17
J34 J36
BROADCOM
LAN
(Optional)
ATI
Rage XL
J46
1
J45
1
1
SMDC J37
J39
1
1
J38
1
J27
FAN1
J41
(Optional)
Use these headers to connect the chassis
cooling fans to your motherboard to keep
the system stable and reliable.
These connectors support the tachometer
monitoring and auto fan speed control.

Tomcat i925X S5130 Chapter 2: Board Installation
2-8
http://www.tyan.com
2.5.5 Audio CD_in Connector: J28 (Optional)
1
4
Pin_4 CD_In_Right
Pin_3 GND
Pin_2 GND
Pin_1 CD_In_Left
USB3
1
1
1
1
J2
(KB+Mouse)
J5
J3 (VGA) J8
(Parallel Port)
J42
PW3
J7
(LAN2+
USB2)
J1
(Audio)
ALC880
P1FAN
J35
BIOS
J31
Intel
i925X
Intel
ICH6R
32-bit 33MHz (5V) PCI PCI2
32-bit 33MHz (5V) PCI PCI3
32-bit 33MHz (5V) PCI PCI4
PCI-E2
SATA2
SATA1
FDD J26
JP2
RAID P-IDEJ33 (Optional) P-IDE J18
1
x16 PCI Express PCI-E1
SUPER
I/O
BT1
PCI-E3 USB4
1
VIA
VT6307
LED16
32-bit 33MHz (5V)PCI PCI1
SATA3
SATA4
FAN2
Promise
PDC20579
(Optional)
J29
1
J28
BROADCOM
LAN
(Optional)
1
J44
J6
(LAN1+
USB1)
J21
COM1
1
JP1
J30 J32
PW2
1
J43
J12
J19 J22
J20 J23
S5130
J4
(SPDIF-IN)
(SPDIF-OUT)
KB(Bottom)
Mouse(Top)
USB (Bottom)
GbE LAN (Top)
USB (Bottom)
GbE LAN (Top)Optional
J17
J34 J36
BROADCOM
LAN
(Optional)
ATI
Rage XL
J46
1
J45
1
1
SMDC J37
J39
1
1
J38
1
J27
FAN1
J41
(Optional)
Use this header to connect to the audio
output of a CD-ROM drive via an optional
CD audio cable so that you can listen to
the audio CDs through the integrated
audio chip on the motherboard.
2.5.6 Front Panel Audio Connector: J29 (Optional)
1 9
2 10
GND Presence AUD FP JS NC AUD VREF
2 4 6 8 10
1 3 5 7 9
1L
1R 2R
AUD FP JS
2L
USB3
1
1
1
1
J2
(KB+Mouse)
J5
J3 (VGA) J8
(Parallel Port)
J42
PW3
J7
(LAN2+
USB2)
J1
(Audio)
ALC880
P1FAN
J35
BIOS
J31
Intel
i925X
Intel
ICH6R
32-bit 33MHz (5V) PCI PCI2
32-bit 33MHz (5V) PCI PCI3
32-bit 33MHz (5V) PCI PCI4
PCI-E2
SATA2
SATA1
FDD J26
JP2
RAID P-IDEJ33 (Optional) P-IDE J18
1
x16 PCI Express PCI-E1
SUPER
I/O
BT1
PCI-E3 USB4
1
VIA
VT6307
LED16
32-bit 33MHz (5V)PCI PCI1
SATA3
SATA4
FAN2
Promise
PDC20579
(Optional)
J29
1
J28
BROADCOM
LAN
(Optional)
1
J44
J6
(LAN1+
USB1)
J21
COM1
1
JP1
J30 J32
PW2
1
J43
J12
J19 J22
J20 J23
S5130
J4
(SPDIF-IN)
(SPDIF-OUT)
KB(Bottom)
Mouse(Top)
USB (Bottom)
GbE LAN (Top)
USB (Bottom)
GbE LAN (Top)Optional
J17
J34 J36
BROADCOM
LAN
(Optional)
ATI
Rage XL
J46
1
J45
1
1
SMDC J37
J39
1
1
J38
1
J27
FAN1
J41
(Optional)
USB3
1
1
1
1
J2
(KB+Mouse)
J5
J3 (VGA) J8
(Parallel Port)
J42
PW3
J7
(LAN2+
USB2)
J1
(Audio)
ALC880
P1FAN
J35
BIOS
J31
Intel
i925X
Intel
ICH6R
32-bit 33MHz (5V) PCI PCI2
32-bit 33MHz (5V) PCI PCI3
32-bit 33MHz (5V) PCI PCI4
PCI-E2
SATA2
SATA1
FDD J26
JP2
RAID P-IDEJ33 (Optional) P-IDE J18
1
x16 PCI Express PCI-E1
SUPER
I/O
BT1
PCI-E3 USB4
1
VIA
VT6307
LED16
32-bit 33MHz (5V)PCI PCI1
SATA3
SATA4
FAN2
Promise
PDC20579
(Optional)
J29
1
J28
BROADCOM
LAN
(Optional)
1
J44
J6
(LAN1+
USB1)
J21
COM1
1
JP1
J30 J32
PW2
1
J43
J12
J19 J22
J20 J23
S5130
J4
(SPDIF-IN)
(SPDIF-OUT)
KB(Bottom)
Mouse(Top)
USB (Bottom)
GbE LAN (Top)
USB (Bottom)
GbE LAN (Top)Optional
J17
J34 J36
BROADCOM
LAN
(Optional)
ATI
Rage XL
J46
1
J45
1
1
SMDC J37
J39
1
1
J38
1
J27
FAN1
J41
(Optional)
Use this header to connect with the front
panel audio outputs.

Tomcat i925X S5130 Chapter 2: Board Installation
2-9
http://www.tyan.com
2.5.7 IEEE1394a Connector: J30 / J32 (Optional)
10 2
9 1
NC NC XTPB+ GND XTPA+
9 7 5 3 1
10 8 6 4 2
GND
VCC
XTPB-
GND
XTPA-
USB3
1
1
1
1
J2
(KB+Mouse)
J5
J3 (VGA) J8
(Parallel Port)
J42
PW3
J7
(LAN2+
USB2)
J1
(Audio)
ALC880
P1FAN
J35
BIOS
J31
Intel
i925X
Intel
ICH6R
32-bit 33MHz (5V) PCI PCI2
32-bit 33MHz (5V) PCI PCI3
32-bit 33MHz (5V) PCI PCI4
PCI-E2
SATA2
SATA1
FDD J26
JP2
RAID P-IDE J33 (Optional) P-IDE J18
1
x16 PCI Express PCI-E1
SUPER
I/O
BT1
PCI-E3 USB4
1
VIA
VT6307
LED16
32-bit 33MHz (5V)PCI PCI1
SATA3
SATA4
FAN2
Promise
PDC20579
(Optional)
J29
1
J28
BROADCOM
LAN
(Optional)
1
J44
J6
(LAN1+
USB1)
J21
COM1
1
JP1
J30 J32
PW2
1
J43
J12
J19 J22
J20 J23
S5130
J4
(SPDIF-IN)
(SPDIF-OUT)
KB(Bottom)
Mouse(Top)
USB (Bottom)
GbE LAN (Top)
USB (Bottom)
GbE LAN (Top)Optional
J17
J34 J36
BROADCOM
LAN
(Optional)
ATI
Rage XL
J46
1
J45
1
1
SMDC J37
J39
1
1
J38
1
J27
FAN1
J41
(Optional)
Use these headers to connect IEEE1394a
(FireWire) type device via the enclosed
1394a cable.
2.5.8 Chassis Fan Connector: J31 (FAN2)
+12VNCGND
USB3
1
1
1
1
J2
(KB+Mouse)
J5
J3 (VGA) J8
(Parallel Port)
J42
PW3
J7
(LAN2+
USB2)
J1
(Audio)
ALC880
P1FAN
J35
BIOS
J31
Intel
i925X
Intel
ICH6R
32-bit 33MHz (5V) PCI PCI2
32-bit 33MHz (5V) PCI PCI3
32-bit 33MHz (5V) PCI PCI4
PCI-E2
SATA2
SATA1
FDD J26
JP2
RAID P-IDEJ33 (Optional) P-IDE J18
1
x16 PCI Express PCI-E1
SUPER
I/O
BT1
PCI-E3 USB4
1
VIA
VT6307
LED16
32-bit 33MHz (5V)PCI PCI1
SATA3
SATA4
FAN2
Promise
PDC20579
(Optional)
J29
1
J28
BROADCOM
LAN
(Optional)
1
J44
J6
(LAN1+
USB1)
J21
COM1
1
JP1
J30 J32
PW2
1
J43
J12
J19 J22
J20 J23
S5130
J4
(SPDIF-IN)
(SPDIF-OUT)
KB(Bottom)
Mouse(Top)
USB (Bottom)
GbE LAN (Top)
USB (Bottom)
GbE LAN (Top)Optional
J17
J34 J36
BROADCOM
LAN
(Optional)
ATI
Rage XL
J46
1
J45
1
1
SMDC J37
J39
1
1
J38
1
J27
FAN1
J41
(Optional)
Use this header to connect the chassis
cooling fan to your motherboard to keep
the system stable and reliable.

Tomcat i925X S5130 Chapter 2: Board Installation
2-10
http://www.tyan.com
2.5.9 Front Panel USB 2.0 Connector: J34/J36 (USB3/USB4)
10 2
9 1
GND GND Data 1+ Data 1 - +5V
9 7 5 3 1
10 8 6 4 2
GND GND
Data 2+ Data 2 -
+5V
USB3
1
1
1
1
J2
(KB+Mouse)
J5
J3 (VGA) J8
(Parallel Port)
J42
PW3
J7
(LAN2+
USB2)
J1
(Audio)
ALC880
P1FAN
J35
BIOS
J31
Intel
i925X
Intel
ICH6R
32-bit 33MHz (5V) PCI PCI2
32-bit 33MHz (5V) PCI PCI3
32-bit 33MHz (5V) PCI PCI4
PCI-E2
SATA2
SATA1
FDD J26
JP2
RAID P-IDE J33 (Optional) P-IDE J18
1
x16 PCI Express PCI-E1
SUPER
I/O
BT1
PCI-E3 USB4
1
VIA
VT6307
LED16
32-bit 33MHz (5V)PCI PCI1
SATA3
SATA4
FAN2
Promise
PDC20579
(Optional)
J29
1
J28
BROADCOM
LAN
(Optional)
1
J44
J6
(LAN1+
USB1)
J21
COM1
1
JP1
J30 J32
PW2
1
J43
J12
J19 J22
J20 J23
S5130
J4
(SPDIF-IN)
(SPDIF-OUT)
KB(Bottom)
Mouse(Top)
USB (Bottom)
GbE LAN (Top)
USB (Bottom)
GbE LAN (Top)Optional
J17
J34 J36
BROADCOM
LAN
(Optional)
ATI
Rage XL
J46
1
J45
1
1
SMDC J37
J39
1
1
J38
1
J27
FAN1
J41
(Optional)
Use these headers to Connect to the USB
devices via the enclosed USB cable.
2.5.10 CPU Fan Connector: J35 (P1FAN)
+12V V3P3
SpeedControl
Tachometer
USB3
1
1
1
1
J2
(KB+Mouse)
J5
J3 (VGA) J8
(Parallel Port)
J42
PW3
J7
(LAN2+
USB2)
J1
(Audio)
ALC880
P1FAN
J35
BIOS
J31
Intel
i925X
Intel
ICH6R
32-bit 33MHz (5V) PCI PCI2
32-bit 33MHz (5V) PCI PCI3
32-bit 33MHz (5V) PCI PCI4
PCI-E2
SATA2
SATA1
FDD J26
JP2
RAID P-IDEJ33 (Optional) P-IDE J18
1
x16 PCI Express PCI-E1
SUPER
I/O
BT1
PCI-E3 USB4
1
VIA
VT6307
LED16
32-bit 33MHz (5V)PCI PCI1
SATA3
SATA4
FAN2
Promise
PDC20579
(Optional)
J29
1
J28
BROADCOM
LAN
(Optional)
1
J44
J6
(LAN1+
USB1)
J21
COM1
1
JP1
J30 J32
PW2
1
J43
J12
J19 J22
J20 J23
S5130
J4
(SPDIF-IN)
(SPDIF-OUT)
KB(Bottom)
Mouse(Top)
USB (Bottom)
GbE LAN (Top)
USB (Bottom)
GbE LAN (Top)Optional
J17
J34 J36
BROADCOM
LAN
(Optional)
ATI
Rage XL
J46
1
J45
1
1
SMDC J37
J39
1
1
J38
1
J27
FAN1
J41
(Optional)
Use this header to connect the processor
cooling fan to your motherboard to keep
the system stable and reliable.
This connector supports the tachometer
monitoring and auto fan speed control.

Tomcat i925X S5130 Chapter 2: Board Installation
2-11
http://www.tyan.com
2.5.11 SMDC Connector: J37 (Optional)
USB3
1
1
1
1
J2
(KB+Mouse)
J5
J3 (VGA) J8
(Parallel Port)
J42
PW3
J7
(LAN2+
USB2)
J1
(Audio)
ALC880
P1FAN
J35
BIOS
J31
Intel
i925X
Intel
ICH6R
32-bit 33MHz (5V) PCI PCI2
32-bit 33MHz (5V) PCI PCI3
32-bit 33MHz (5V) PCI PCI4
PCI-E2
SATA2
SATA1
FDD J26
JP2
RAID P-IDE J33 (Optional) P-IDE J18
1
x16 PCI Express PCI-E1
SUPER
I/O
BT1
PCI-E3 USB4
1
VIA
VT6307
LED16
32-bit 33MHz (5V)PCI PCI1
SATA3
SATA4
FAN2
Promise
PDC20579
(Optional)
J29
1
J28
BROADCOM
LAN
(Optional)
1
J44
J6
(LAN1+
USB1)
J21
COM1
1
JP1
J30 J32
PW2
1
J43
J12
J19 J22
J20 J23
S5130
J4
(SPDIF-IN)
(SPDIF-OUT)
KB(Bottom)
Mouse(Top)
USB (Bottom)
GbE LAN
(
Top
)
USB (Bottom)
GbE LAN
(
Top
)
Optional
J17
J34 J36
BROADCOM
LAN
(Optional)
ATI
Rage XL
J46
1
J45
1
1
SMDC J37
J39
1
1
J38
1
J27
FAN1
J41
(Optional)
For connection with Tyan Server Management
Daughter Card (SMDC)
2.5.12 Front Panel LAN1/LAN2 Link and Active LED Connector: J38/J39 (Optional)
1
Pin 1: LED+
Pin 2: LED-
USB3
1
1
1
1
J2
(KB+Mouse)
J5
J3 (VGA) J8
(Parallel Port)
J42
PW3
J7
(LAN2+
USB2)
J1
(Audio)
ALC880
P1FAN
J35
BIOS
J31
Intel
i925X
Intel
ICH6R
32-bit 33MHz (5V) PCI PCI2
32-bit 33MHz (5V) PCI PCI3
32-bit 33MHz (5V) PCI PCI4
PCI-E2
SATA2
SATA1
FDD J26
JP2
RAID P-IDEJ33 (Optional) P-IDE J18
1
x16 PCI Express PCI-E1
SUPER
I/O
BT1
PCI-E3 USB4
1
VIA
VT6307
LED16
32-bit 33MHz (5V)PCI PCI1
SATA3
SATA4
FAN2
Promise
PDC20579
(Optional)
J29
1
J28
BROADCOM
LAN
(Optional)
1
J44
J6
(LAN1+
USB1)
J21
COM1
1
JP1
J30 J32
PW2
1
J43
J12
J19 J22
J20 J23
S5130
J4
(SPDIF-IN)
(SPDIF-OUT)
KB(Bottom)
Mouse(Top)
USB (Bottom)
GbE LAN (Top)
USB (Bottom)
GbE LAN (Top)Optional
J17
J34 J36
BROADCOM
LAN
(Optional)
ATI
Rage XL
J46
1
J45
1
1
SMDC J37
J39
1
1
J38
1
J27
FAN1
J41
(Optional)
Use these headers to connect with the
front panel link/activity LEDs for LAN1 and
LAN2.

Tomcat i925X S5130 Chapter 2: Board Installation
2-12
http://www.tyan.com
2.5.13 Front Panel System Connector: J40
Your chassis will usually come with connectors to install onto the motherboard, such as HD
and Power LEDs. The Front Panel Connector (J40) has been implemented for such purposes.
1 2
17 18
Function PIN PIN Function
HD_LED+ 1 2 PWR+
HD_LED- 3 4 PWR-
GND 5 6 Power Button
Reset
Button 7 8 GND
+5V 9 10 Sleep Button
NIMI 11 12 GND
+5VSB 13 14 NC
SMBUS
Data 15 16 GND
USB3
1
1
1
1
J2
(KB+Mouse)
J5
J3 (VGA) J8
(Parallel Port)
J42
PW3
J7
(LAN2+
USB2)
J1
(Audio)
ALC880
P1FAN
J35
BIOS
J31
Intel
i925X
Intel
ICH6R
32-bit 33MHz (5V) PCI PCI2
32-bit 33MHz (5V) PCI PCI3
32-bit 33MHz (5V) PCI PCI4
PCI-E2
SATA2
SATA1
FDD J26
JP2
RAID P-IDE J33 (Optional) P-IDE J18
1
x16 PCI Express PCI-E1
SUPER
I/O
BT1
PCI-E3 USB4
1
VIA
VT6307
LED16
32-bit 33MHz (5V)PCI PCI1
SATA3
SATA4
FAN2
Promise
PDC20579
(Optional)
J29
1
J28
BROADCOM
LAN
(Optional)
1
J44
J6
(LAN1+
USB1)
J21
COM1
1
JP1
J30 J32
PW2
1
J43
J12
J19 J22
J20 J23
S5130
J4
(SPDIF-IN)
(SPDIF-OUT)
KB(Bottom)
Mouse(Top)
USB (Bottom)
GbE LAN (Top)
USB (Bottom)
GbE LAN (Top)Optional
J17
J34 J36
BROADCOM
LAN
(Optional)
ATI
Rage XL
J46
1
J45
1
1
SMDC J37
J39
1
1
J38
1
J27
FAN1
J41
(Optional)
SMBUS
Clock 17 18 INTRU#
2.5.14 Chassis Fan Connector: J42 (FAN3)
+12V
SpeedControl
GN
D
USB3
1
1
1
1
J2
(KB+Mouse)
J5
J3 (VGA) J8
(Parallel Port)
J42
PW3
J7
(LAN2+
USB2)
J1
(Audio)
ALC880
P1FAN
J35
BIOS
J31
Intel
i925X
Intel
ICH6R
32-bit 33MHz (5V) PCI PCI2
32-bit 33MHz (5V) PCI PCI3
32-bit 33MHz (5V) PCI PCI4
PCI-E2
SATA2
SATA1
FDD J26
JP2
RAID P-IDEJ33 (Optional) P-IDE J18
1
x16 PCI Express PCI-E1
SUPER
I/O
BT1
PCI-E3 USB4
1
VIA
VT6307
LED16
32-bit 33MHz (5V)PCI PCI1
SATA3
SATA4
FAN2
Promise
PDC20579
(Optional)
J29
1
J28
BROADCOM
LAN
(Optional)
1
J44
J6
(LAN1+
USB1)
J21
COM1
1
JP1
J30 J32
PW2
1
J43
J12
J19 J22
J20 J23
S5130
J4
(SPDIF-IN)
(SPDIF-OUT)
KB(Bottom)
Mouse(Top)
USB (Bottom)
GbE LAN (Top)
USB (Bottom)
GbE LAN (Top)Optional
J17
J34 J36
BROADCOM
LAN
(Optional)
ATI
Rage XL
J46
1
J45
1
1
SMDC J37
J39
1
1
J38
1
J27
FAN1
J41
(Optional)
Use this header to connect the chassis
cooling fans to your motherboard to keep
the system stable and reliable.
This connector supports the auto fan
speed control.

Tomcat i925X S5130 Chapter 2: Board Installation
2-13
http://www.tyan.com
2.5.15 Chassis Fan Connector: J43/J44 (FAN4/FAN5)
+12V
SpeedControl
Tachometer
USB3
1
1
1
1
J2
(KB+Mouse)
J5
J3 (VGA) J8
(Parallel Port)
J42
PW3
J7
(LAN2+
USB2)
J1
(Audio)
ALC880
P1FAN
J35
BIOS
J31
Intel
i925X
Intel
ICH6R
32-bit 33MHz (5V) PCI PCI2
32-bit 33MHz (5V) PCI PCI3
32-bit 33MHz (5V) PCI PCI4
PCI-E2
SATA2
SATA1
FDD J26
JP2
RAID P-IDEJ33 (Optional) P-IDE J18
1
x16 PCI Express PCI-E1
SUPER
I/O
BT1
PCI-E3 USB4
1
VIA
VT6307
LED16
32-bit 33MHz (5V)PCI PCI1
SATA3
SATA4
FAN2
Promise
PDC20579
(Optional)
J29
1
J28
BROADCOM
LAN
(Optional)
1
J44
J6
(LAN1+
USB1)
J21
COM1
1
JP1
J30 J32
PW2
1
J43
J12
J19 J22
J20 J23
S5130
J4
(SPDIF-IN)
(SPDIF-OUT)
KB(Bottom)
Mouse(Top)
USB (Bottom)
GbE LAN (Top)
USB (Bottom)
GbE LAN (Top)Optional
J17
J34 J36
BROADCOM
LAN
(Optional)
ATI
Rage XL
J46
1
J45
1
1
SMDC J37
J39
1
1
J38
1
J27
FAN1
J41
(Optional)
Use these headers to connect the chassis
cooling fans to your motherboard to keep
the system stable and reliable.
These connectors support the tachometer
monitoring and auto fan speed control.
2.5.16 Front Panel LAN1/LAN2 Speed LED Pin-Header: J45/J46 (Optional)
1
Pin 1: Orange+
Pin 2: Green+
USB3
1
1
1
1
J2
(KB+Mouse)
J5
J3 (VGA) J8
(Parallel Port)
J42
PW3
J7
(LAN2+
USB2)
J1
(Audio)
ALC880
P1FAN
J35
BIOS
J31
Intel
i925X
Intel
ICH6R
32-bit 33MHz (5V) PCI PCI2
32-bit 33MHz (5V) PCI PCI3
32-bit 33MHz (5V) PCI PCI4
PCI-E2
SATA2
SATA1
FDD J26
JP2
RAID P-IDEJ33 (Optional) P-IDE J18
1
x16 PCI Express PCI-E1
SUPER
I/O
BT1
PCI-E3 USB4
1
VIA
VT6307
LED16
32-bit 33MHz (5V)PCI PCI1
SATA3
SATA4
FAN2
Promise
PDC20579
(Optional)
J29
1
J28
BROADCOM
LAN
(Optional)
1
J44
J6
(LAN1+
USB1)
J21
COM1
1
JP1
J30 J32
PW2
1
J43
J12
J19 J22
J20 J23
S5130
J4
(SPDIF-IN)
(SPDIF-OUT)
KB(Bottom)
Mouse(Top)
USB (Bottom)
GbE LAN (Top)
USB (Bottom)
GbE LAN (Top)Optional
J17
J34 J36
BROADCOM
LAN
(Optional)
ATI
Rage XL
J46
1
J45
1
1
SMDC J37
J39
1
1
J38
1
J27
FAN1
J41
(Optional)
Use these headers to connect with the
front panel dual color LEDs to indicate the
speed of LAN1 and LAN2.
(Green=10/100 LAN, Orange=GbE LAN)
Reference Section 2.11.1 (page 2-22) for
the correct LAN LED Color Definition.
J45 is for LAN1, J46 is for LAN2.