TYAN FT48 B7025 User manual

http://www.tyan.com
1
TYAN®FT48
B7025
Service Engineer’s Manual

http://www.tyan.com
2

http://www.tyan.com
3
PREFACE
Copyright
This publication, including all photographs, illustrations, and software, is
protected under international copyright laws, with all rights reserved.
Neither this manual, nor any material contained herein, may be reproduced
without written consent of manufacturer.
Copyright 2009 MiTAC International Corporation. All rights reserved.
TYAN®is a registered trademark of MiTAC International Corporation.
Version 1.00
Disclaimer
Information contained in this document is furnished by MiTAC Computer
Corporation and has been reviewed for accuracy and reliability prior to
printing. TYAN®assumes no liability whatsoever, and disclaims any
express or implied warranty, relating to sale and/or use of TYAN®products
including liability or warranties relating to fitness for a particular purpose or
merchantability. TYAN®retains the right to make changes to produce
descriptions and/or specifications at any time, without notice. In no event
will TYAN®be held liable for any direct or indirect, incidental or
consequential damage, loss of use, loss of data or other malady resulting
from errors or inaccuracies of information contained in this document.
Trademark Recognition
All registered and unregistered trademarks and company names contain-
-ed in this manual are property of their respective owners including, but not
limited to the following.
TYAN®is a trademark of MiTAC Computer Corporation
Intel®is a trademark of Intel®Corporation.
AMI®, AMIBIOS® and combinations thereof are trademarks of AMI
Technologies.
Microsoft®, Windows®are trademarks of Microsoft Corporation.
Winbond®is a trademark of Winbond Electronics Corporation.

http://www.tyan.com
4
Federal Communication Commission (FCC)
Notice for the USA
Compliance Information Statement (Declaration of
Conformity Procedure) DoC FCC Part 15: This
device complies with part 15 of the FCC Rules
Operation is subject to the following conditions:
1) This device may not cause harmful interference;
2) This device must accept any interference received including
interference that may cause undesired operation. If this equipment
does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the
user is encouraged to try one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and the receiver.
– Plug the equipment into an outlet on a circuit different from that of
the receiver.
Consult the dealer on an experienced radio/television technician for
help.
Notice for Canada
This apparatus complies with the Class A limits for radio interference as
specified in the Canadian Department of Communications Radio
Interference Regulations. (Cet appareil est conforme aux norms de
Classe A d’interference radio tel que specifie par le Ministere Canadien
des Communications dans les reglements d’ineteference radio.)
Notice for Europe (CE Mark)
This product is in conformity with the Council
Directive 89/336/EEC, 92/31/EEC (EMC).
CAUTION: Lithium battery included with this board. Do not puncture,
mutilate, or dispose of battery in fire. There will be danger of explosion if
battery is incorrectly replaced. Replace only with the same or equivalent
type recommended by manufacturer. Dispose of used battery according
to manufacturer instructions and in accordance with your local regulatio-
-ns.

http://www.tyan.com
5
About this Manual
This manual provides you with instructions on installing your
TYAN®GT20. This Manual is intended for experienced users and
integrators with hardware knowledge of personal computers.
This manual consists of the following parts:
Chapter1: Provides an introduction to the FT48-B7025 bare-
-bones, standard parts list, describes the external
components, gives a table of key components,
and provides block diagram of the system.
Chapter2: Covers procedures on installing the CPU, memory
modules and hard drives.
Chapter3:
Covers removal and replacement procedures for
pre-installed components.
Appendix:
List the BIOS differences, cable connection and FRU
part tables for reference of system setup, and
technical support in case a problem arises with your
system.
For information on the motherboard, please refer to the attached
motherboard user’s manual. You can find the detailed descripti-
-on about jumper and BIOS settings from the motherboard man-
-ual.

http://www.tyan.com
6
SAFETY INFORMATION
Before installing and using FT48-B7025, take note of the following
precautions:
·Read all instructions carefully.
·Do not place the unit on an unstable surface, cart, or stand.
·Do not block the slots and opening on the unit, which are provided for
ventilation.
·Only use the power source indicated on the marking label. If you are not
sure, contact the power company.
·The unit uses a three-wire ground cable, which is equipped with a third
pin to ground the unit and prevent electric shock. Do not defeat the pur-
-pose of this pin. If you outlet does not support this kind of plug, contact
your electrician to replace your obsolete outlet.
·Do not place anything on the power cord. Place the power cord where it
will not be in the way of foot traffic.
·Follow all warnings and cautions in this manual and on the unit case.
·Do not push objects in the ventilation slots as they may touch high volta-
-ge components and result in shock and damage to the components.
·When replacing parts, ensure that you use parts specified by the manuf-
-acturer.
·When service or repairs have been done, perform routine safety checks
to verify that the system is operating correctly.
·Avoid using the system near water, in direct sunlight, or near a heating
device.
·Cover the unit when not in use.

http://www.tyan.com
7
Table of Contents
Chapter 1: Overview.........................................................................9
1.1 About the TYAN FT48-B7025...................................................9
1.2 Product Models.........................................................................9
1.2 Product Models.......................................................................10
1.3 Features..................................................................................11
1.4 Standard Parts List.................................................................14
1.4.1 Box Contents...................................................................14
1.4.2 Accessories .....................................................................16
1.5 Optional Parts.........................................................................17
1.6 About the Product...................................................................18
1.6.1 System Front View...........................................................18
1.6.2 System Rear View...........................................................18
1.6.3 LED Definitions................................................................19
1.6.4 Motherboard (S7025) Layout...........................................21
1.6.5 Jumpers & Connectors....................................................22
1.6.6 System Block Diagram ....................................................23
1.6.7 Internal View....................................................................24
Chapter 2: Setting Up.....................................................................25
2.0.1 Before you Begin.............................................................25
2.0.2 Work Area........................................................................25
2.0.3 Tools................................................................................25
2.0.4 Precautions......................................................................26
2.1 Installing Motherboard Components.......................................27
2.1.1 Removing the Chassis Cover..........................................27
2.1.2 Installing the CPU and Heatsink......................................28
2.1.3 Installing the Memory.......................................................30
2.1.4 Installing the PCI-E Cards...............................................33
2.2 Installing Hard Drives..............................................................35

http://www.tyan.com
8
2.3 Rack Mounting........................................................................37
2.3.1 Installing the Server in a Rack.........................................37
2.4 Opening the Chassis Front Bezel...........................................41
Chapter 3: Replacing Pre-Installed Components ........................43
3.1 Introduction.............................................................................43
3.2 Disassembly Flowchart...........................................................43
3.3 Removing the Cover...............................................................44
3.4 Replacing the System Fan and Fan Board ............................44
3.4.1 M1014 Fan Board Features.............................................46
3.4.2 M1014 Fan Board Connector Pin Definition....................47
3.5 Replacing M1216-P SATA/SAS Backplane ...........................48
3.5.1 M1216-P SATA/SAS Backplane Features ......................49
3.5.2 M1216-P Connector Pin Definition...................................50
3.6 Replacing the Front Panel Control Board...............................50
3.6.1 M1018 LED Control Board Features...............................52
3.6.2 M1018 LED Control Board Connector Pin Definition ......53
3.7 Replacing Power Supply and M7025 PDB.............................54
3.7.1 Replacing Power Supply .................................................54
3.7.2 Replacing M7025 Power Distribution Board....................54
3.7.3 M7025 Power Distribution Board Features .....................57
3.7.4 M7025 PDB Connector Pin Definition .............................58
3.8 Replacing S7025 System Board.............................................60
Appendix I: Cable Connection Tables ..........................................61
Appendix II: FRU Parts Table ........................................................63
Appendix III: Technical Support....................................................65

http://www.tyan.com
9
Chapter 1: Overview
1.1 About the TYAN FT48-B7025
Congratulations on your purchase of the TYAN®FT48-B7025, a highly
optimized rack-mountable 4U barebone system. FT48-B7025 is designed
to support dual Intel®Nehalem-EP/Nehalem-WS 2S processors and up
to 6 channels with 18 DDR3 DIMMs, providing a rich feature set and
incredible performance. Leveraging advanced technology from Intel®,
FT48-B7025 server system is capable of offering scalable 32 and 64-bit
computing, high-bandwidth memory design, and lightning-fast PCI-E bus
implementation. FT48-B7025 not only enpowers your company in today’s
demanding IT environment but also offers a smooth path for future
application usage.
FT48-B7025 uses rack-mountable 4U chassis featuring a robust structure
and a solid mechanical enclosure. All of this provides FT48-B7025 the
power and flexibility to meet the needs of nearly any server application.

http://www.tyan.com
10
1.2 Product Models
Model HDD Bays Power supply
B7025F48W4H (4) 3.5" Hot-Swap HDD
Bays; Extra (4) hot-swap
trays available for add-on
ERP1U hot-swap /
(2+0)
B7025F48W8HR (8) 3.5" Hot-Swap HDD
Bays; ERP1U hot-swap / (2+1)

http://www.tyan.com
11
1.3 Features
TYAN FT48-B7025 (B7025F48W4H / B7025F48W8HR (BTO))
Form Factor 4U Rack mount
Chassis Model FT48
Dimension (H x W x D) 6.9" x 16.7" x 27.6" (176 x 425 x 700mm)
Motherboard S7025WAGM2NR-B
System
Gross Weight 46.8 kg
Buttons (1) RST / (1) ID / (1) PWR / (1) NMI
LEDs (1) Power / (1) ID / (2) LAN / (1) HDD
(1) Warning
Front Panel
I/O Ports (2) USB ports
Type / QTY 3.5" Hot-Swap / (4)
Extra (4) hot-swap trays available for
adding-on
External
Drive
Bay Supported HDD
Interface SAS 3.0Gb/s
System
Cooling
Configuration FAN (3) 12cm fans
Type
ERP1U swappable / (2+0)
(B7025F48W4H),
ERP1U hot-swap / (2+1)
(B7025F48W8HR)
Input Range Full-range AC(100-240V)
Frequency 47 - 63 Hertz
Output Watts 1,300 Watts (2x 650W)
Power Supply
Efficiency PFC / 80-plus
Supported CPU
Series Intel® Xeon® processor 5500 series
Socket Type / QTY LGA1366 / (2)
Thermal Design
Power (TDP) wattage Max. up to 95W
Processor
System Bus Up to 4.8/ 5.86/ 6.4GT/s with Intel Quick
Path Interconnect (QPI) support
Chipset Chipset (2) Intel 5520 / ICH10R
Supported DIMM QTY (4+4) DIMM slots
DIMM Type / Speed DDR3 800/1066/1333 RDIMM/UDIMM
Capacity Up to 64GB RDIMM / 32GB UDIMM
Memory channel 6 Channels (3 Channels per CPU)
Memory
Memory voltage 1.5V
PCI-E (4) FH/FL PCI-E Gen.2 x16 slots (1) FH/FL PCI-E Gen.2 x8 slot (w/ x4 link)
(1) FH/FL PCI-E Gen.2 x4 slot
Expansion
Slots PCI (1) FH/FL PCI 32/33MHz slot
Port QTY (2)
LAN Controller Intel 82574L

http://www.tyan.com
12
Controller LSI SAS1068E
Speed 3.0 Gb/s
SAS RAID RAID 0/1/1E (LSI Integrated RAID)
Controller ICH10R
Speed 3.0 Gb/s
Storage
SATA RAID RAID 0/1/10/5 (Intel®Matrix RAID)
Connector type D-Sub 15-pin
Resolution 1600x1200@60Hz
Graphic Chipset Aspeed AST2050
Chipset Realtek ALC262
Audio Feature HDA 2.0 spec. complaint
Chipset Infineon SLB9635
TPM Version TPM v1.2
USB (7) USB2.0 ports (4 at rear, 2 at front, 1
type A onboard)
COM (1) DB-9 port
VGA (1) D-Sub 15-pin VGA port
Input /Output
RJ-45 (2) GbE ports
Chipset Winbond W83793G
Voltage Monitors voltage for CPU, memory,
chipset & power supply
Temperature Monitors temperature for CPU & system
environment
LED
(On system front
panel)
Fan fail LED indicator
Over temperature warning indicator
System
Monitoring
Others Watchdog timer support
Onboard Chipset Onboard Aspeed AST2050
AST2050 IPMI Feature
IPMI 2.0 compliant baseboard
management controller (BMC)
BIOS update
USB 2.0 virtual hub
Server
Management
AST2050 iKVM
Feature 24-bit high quality video compression Dual 10/100 Mb/s MAC interfaces
Brand / ROM size AMI / 4MB
BIOS Feature
Plug and Play (PnP)
PCI2.3 /WfM2.0 /SMBIOS2.3 /PXE boot
ACPI 2.0 power management
Power on mode after power recovery
User-configurable H/W monitoring
Auto-configurable of hard disk types
Multiple boot options
Operating
System OS supported list Please refer to our OS supported list.
FCC (DoC) Class A
Regulation CE (DoC) Yes

http://www.tyan.com
13
Operating Temp. 10° C ~ 35° C (50° F~ 95° F)
Non-operating Temp. - 40° C ~ 70° C (-40° F ~ 158° F)
Operating
Environment In/Non-operating
Humidity 90%, non-condensing at 35° C
RoHS RoHS 6/6 Complaint Yes

http://www.tyan.com
14
1.4 Standard Parts List
This section describes FT48-B7025 package contents and accessories.
Open the box carefully and ensure that all components are present and
undamaged. The product should arrive packaged as illustrated below.
1.4.1 Box Contents
Component Description
4U FT48 Chassis
MAIN BOARD,S7025WAGM2NR-B
650W,PowerSupply,
DeltaDPS-650JB B
120X120X38MM FAN,12V,
4800RPM, Delta 4-pin
Front Panel board, Antrada

http://www.tyan.com
15
SAS Backplane board, 4-port,Antrada
PWR Backplane board (R02)
FAN control board, Antrada

http://www.tyan.com
16
1.4.2 Accessories
If any items are missing or appear damaged, contact your retailer or
browse to TYAN’s website for service: http://www.tyan.com
The web site also provides information of other TYAN®products, as
well as FAQs, compatibility lists, BIOS settings, etc.
1 x TYAN®
Motherboard Drive CD 2 x Heatsinks
HDD Screws Power Cables
Left to right: Europe, US
Mounting Ears &
Screws Barebone Manual & Mainboard Manual

http://www.tyan.com
17
Rail Kit
Rail with Bracket x 2 Screw Sack
1.5 Optional Parts
Item Model
Number Picture QTY Description
3.5'' HDD TRAY CHDT-0130 4 3.5'' EXTERNAL HDD TRAY
5.25'' Dummy
DVD-ROM CHDT-0100 3 5.25'' Dummy CD-ROM Tray Assy
PSU CPSU-0330 1 650W,Power Supply, Delta
DPS-650JB B
SAS backplane M1216-P
1 SAS Backplane board, 4-port,
A
ntrada
Mini-SAS Cable CCBL-067W 1 CABLE ASSY;SAS CABLE,SHORT
MINI-SAS 36P/SATA 4X7P 180°,
L=500MM
HDD BP PWR
Cable CCBL-1094 1 CABLE ASSY;HDD BP PWR
CABLE, 2*2P, P4.2/B4P(F),P5.08/
B4P(F),P5.08, L=550+50MM
DVD-ROM SATA
PWR Cable CCBL-1095 1
CABLE ASSY;HDD BP PWR
CABLE,B4P(M), P4.2/B4P(F),
P4.2/5P, P3.81/5P, P3.81/5P,
P3.81, L=50/500+80+80MM
DVD-ROM B4P
PWR Cable CCBL-1096 1
CABLE ASSY;HDD BP PWR
CABLE,B4P(M),P4.2/B4P(F),P4.2/
B4P(F),P4.2/B4P(F),P4.2/B4P(F),
P4.2, L=50/500+80+80MM

http://www.tyan.com
18
1.6 About the Product
The following views show you the product.
1.6.1 System Front View
1.6.2 System Rear View
Hot-swap HDD Bays LED control panel
Power Button
Reset Button
NMI Button
ID LED LAN2 LED
LAN1 LED
HDD LED
Warnin
g
LED
Power LED ID Button
USB Ports
3 * 5.25 inch device bays
Expansion slots
Power Supply
USB Ports
VGA and COM Ports
Thumb Screw
for MB Tray
L
A
N1
(
L
)
/LAN2
(
R
)
Thumb Screw
for top cover

http://www.tyan.com
19
1.6.3 LED Definitions
Front Panel
LED State Color Description
Green On Power on
Power LED ---- Off Power off
Green Blinking HDD access activity
HDD LED ---- Off No disk activity
Green Blinking LAN Accessing
LAN1/LAN2
Activity ---- Off No LAN link
Red On Fan failure/ Over temperature/
Voltage failure
Warning
LED ---- Off Normal
ID LED
LED State Color Description
On Blue System identified
ID LED Off Off System not identified
Note: Press ID button when the system is AC (Alternating Current) on, then ID
LED will show the system is identified with emitting blue light. Users from
remote site could also activate ID LED by input a few commands in IPMI,
detailed software support please visit http://www.tyan.com for lastest
AST2050 user guide.
Rear I/O
LAN1
LED State Color Description
On Green 10Mb/100Mb/1000Mb linked
Blinking Green 10Mb/100Mb/1000Mb activity
RJ-45
Linkage/
Activity(left) Off Off No LAN linked
On Amber 1000Mb linked/activity
On Green 100Mb linked/activity
RJ-45
Linkage/
Activity(Right) Off Off 10Mb mode or No LAN linked

http://www.tyan.com
20
LAN2 (shared by BMC)
LED State Color Description
On Green 10Mb/100Mb/1000Mb linked
Blinking Green 10Mb/100Mb/1000Mb activity
RJ-45 Linkage/
Activity(left) Off Off No LAN linked
On Amber 1000Mb linked/activity
On Green 100Mb linked/activity
RJ-45 Linkage/
Activity(Right) Off Off 10Mb mode or No LAN linked
NOTE: “Left” and “Right” are viewed from the rear panel.