TYAN FT83-B7119 Quick start guide

FT83-B7119
Service Engineer’s Manual

2
http://www.tyan.com
PREFACE
Copyright
This publication, including all photographs, illustrations, and software, is protected
under international copyright laws, with all rights reserved. Neither this manual, nor
any material contained herein, may be reproduced without written consent of
manufacturer.
Copyright 2019 MITAC COMPUTING TECHNOLOGY CORPORATION. All rights
reserved. TYAN®is a registered trademark of MITAC COMPUTING
TECHNOLOGY CORPORATION.
Version 1.0
Disclaimer
Information contained in this document is furnished by MiTAC Computer
Corporation and has been reviewed for accuracy and reliability prior to printing.
TYAN®assumes no liability whatsoever, and disclaims any express or implied
warranty, relating to sale and/or use of TYAN®products including liability or
warranties relating to fitness for a particular purpose or merchantability. TYAN®
retains the right to make changes to produce descriptions and/or specifications at
any time, without notice. In no event will TYAN®be held liable for any direct or
indirect, incidental or consequential damage, loss of use, loss of data or other
malady resulting from errors or inaccuracies of information contained in this
document.
Trademark Recognition
All registered and unregistered trademarks and company names contain- -ed in
this manual are property of their respective owners including, but not limited to the
following.
TYAN®is a trademark of MITAC COMPUTING TECHNOLOGY CORPORATION.
Intel®is a trademark of Intel®Corporation.
AMI®, AMIBIOS® and combinations thereof are trademarks of AMI Technologies.
Microsoft®, Windows®are trademarks of Microsoft Corporation.
IBM®, PC®, AT®and PS/2®are trademarks of IBM Corporation.
Winbond®is a trademark of Winbond Electronics Corporation.

3
http://www.tyan.com
FCC Declaration
Notice for the USA
Compliance Information Statement (Declaration of Conformity Procedure) DoC FCC
Part 15: This device complies with part 15 of the FCC Rules.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following conditions:
‧This device may not cause harmful interference.
‧This device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
Notice for Canada
This Class A digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la Classe A est conforme àla norme NMB-003 du Canada.
●Notice for Europe (CE Mark)
This product is in conformity with the Council Directive 2014/30/EU.

4
http://www.tyan.com
Warning
This equipment is compliant with Class A of CISPR 32. In a residential environment
this equipment may cause radio interference.
This equipment is not suitable for use in locations where children are likely to be
present.
CAUTION
Lithium battery included with this board. Do not puncture, mutilate, or dispose of
battery in fire. There will be danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by manufacturer.
Dispose of used battery according to manufacturer instructions and in accordance
with your local regulations.
The elements of the instructional safeguard shall be as follows:
-element 1a: IEC 60417-6056 (2011-05) for moving fan blades or
IEC 60417-6057 (2011-05) for other moving parts
-element 2:”Moving parts”or “Moving fan blade”as applicable, or equivalent text
-element 3: optional
-element 4: Keep body parts away from moving parts”or “Keep body parts away
from fan blades”or “Keep body parts out of the motion path”as applicable, or
equivalent text
●VCCI-A
この装置は、クラスＡ情報技術装置です。この装置を家庭環境で使用すると電波妨
害を引き起こすことがあります。この場合には使用者が適切な対策を講ずるよう要
求されることがあります。 VCCI-A
●Safety: IEC/EN 62368-1
This equipment is compliant with CB/LVD of Safety: IEC/EN 62368-1.
Warning
keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and
keep it away from children.

5
http://www.tyan.com
If you think batteries might have been swallowed or placed inside any part of the
body, seek immediate medical attention.
About this Manual
This Manual is intended for trained service technician/personnel with hardware
knowledge of personal computers. It is aimed to provide you with instructions on
installing your TYAN FT83-B7119.
How this guide is organized
This guide contains the following parts:
Chapter 1: Overview
This chapter give an introduction to the FT83-B7119 barebones, standard parts
list, and accessories. describes the external components, gives a table of key
Chapter2: Setting Up
This chapter Covers procedures on installing the CPU, memory modules, add
on card and hard drives. Give an overview about the FT83-B7119 barebone
from an overall angle.
Chapter 3: Replacing the Pre-installed Components
This chapter covers the removal and replacement procedures for pre-installed
components.
Chapter 4: Motherboard Information
This chapter lists the hardware setup procedures that you need to abide by when
installing system components. It includes description of the jumpers and connectors
on the motherboard.
Chapter5: BIOS Setup
This chapter tells how to change system settings through the BIOS setup menu.
Detailed descriptions of the BIOS parameters are also provided.
Chapter 6: Diagnostics
This chapter introduces some BIOS codes and technical terms to provide better
service for the customers.
Appendix:
This Chapter Describes the Fan and Temp sensors location; list the cable
connection and FRU part tables for reference of system setup and technical
support in case a problem arises with your system.

6
http://www.tyan.com
Safety and Compliance Information
Before installing and using TYAN FT83-B7119, take note of the following
precautions:
·Read all instructions carefully.
·Do not place the unit on an unstable surface, cart, or stand.
·Do not block the slots and opening on the unit, which are provided for
ventilation.
·Only use the power source indicated on the marking label. If you are not
sure, contact the power company.
·The unit uses a three-wire ground cable, which is equipped with a third pin to
ground the unit and prevent electric shock. Do not defeat the purpose of this
pin. If your outlet does not support this kind of plug, contact your electrician
to replace your obsolete outlet.
·Do not place anything on the power cord. Place the power cord where it will
not be in the way of foot traffic.
·Follow all warnings and cautions in this manual and on the unit case.
·Do not push objects in the ventilation slots as they may touch high voltage
components and result in shock and damage to the components.
·When replacing parts, ensure that you use parts specified by the
manufacturer.
·When service or repairs have been done, perform routine safety checks
to verify that the system is operating correctly.
·Avoid using the system near water, in direct sunlight, or near a heating
device.
·Cover the unit when not in use.

7
http://www.tyan.com
Safety Information
Retain and follow all product safety and operating instructions provided
with your equipment. In the event of a conflict between the instructions in
this guide and the instructions in equipment documentation, follow the
guidelines in the equipment documentation.
Observe all warnings on the product and in the operating instructions. To
reduce the risk of bodily injury, electric shock, fire and damage to the
equipment, observe all precautions included in this guide.
You must become familiar with the safety information in this guide before
you install, operate, or service TYAN products.
Symbols on Equipment
Caution. This symbol indicates a potential hazard.
The potential for injury exists if cautions are not
observed. Consult equipment documentation for
specific details.
Warning. This symbol indicates the presence of
hazardous energy circuits or electric shock hazards.
Refer all servicing to qualified personnel.
Warning. This symbol indicates the presence of a
hot surface or hot component. If this surface is
contacted, the potential for injury exists.
To reduce risk of injury from a hot component, allow
the surface to cool before touching.
Warning. This symbol indicates hazardous moving
parts. Keep away from moving fan blades.
Caution. Slide-mounted equipment is not to be
used as a shelf or a work space.

8
http://www.tyan.com
General Precautions
·Follow all caution and warning instructions marked on the equipment and
explained in the accompanying equipment documentation.

Machine Room Environment
 ·Make sure that the area in which you install the system is properly
ventilated and climate-controlled.
·Ensure that the voltage and frequency of your power source match the
voltage and frequency inscribed on the electrical rating label of the
equipment.
·Do not install the system in or near a plenum, air duct, radiator, or heat
register.
·Never use the product in a wet location.
Equipment Chassis
·Do not block or cover the openings to the system.
·Never push objects of any kind through openings in the equipment.
Dangerous voltages might be present.
·Conductive foreign objects can produce a short circuit and cause fire,
electric shock, or damage to your equipment.
·Lift equipment using both hands and with your knees bent.
Equipment Racks
To avoid injury or damage to the equipment:
·Observe local occupational health and safety requirements and guidelines
for manual materials handling.
·Do not attempt to move a rack by yourself; a minimum of two people are
needed to move a rack.
·Do not attempt to move a fully loaded rack. Remove equipment from the
rack before moving it.
·Do not attempt to move a rack on an incline that is greater than 10 degrees
from the horizontal.

9
http://www.tyan.com
·Make sure the rack is properly secured to the floor or ceiling.
·Make sure the stabilizing feet are attached to the rack if it is a single-rack
installation.
·Make sure racks are coupled together if it is a multiple-rack installation.
·Make sure the rack is level and stable before installing an appliance in the
rack.
·Make sure the leveling jacks are extended to the floor.
·Make sure the full weight of the rack rests on the leveling jacks.
·Always load the rack from the bottom up. Load the heaviest component in
the rack first.
·Make sure the rack is level and stable before pulling a component out of the
rack.
·Make sure only one component is extended at a time. A rack might become
unstable if more than one component is extended.
To avoid damage to the equipment:
·The rack width and depth must allow for proper serviceability and cable
management.
·Ensure that there is adequate airflow in the rack. Improper installation or
restricted airflow can damage the equipment.
·The rack cannot have solid or restricted airflow doors. You must use a
mesh door on the front and back of the rack or remove the doors to ensure
adequate air flow to the system.
·If you install the Model in a rack, do not place equipment on top of the unit.
It will cause restricted airflow and might cause damage to the equipment.
·Make sure the product is properly matted with the rails. Products that are
improperly matted with the rails might be unstable.
·Verify that the AC power supply branch circuit that provides power to the
rack is not overloaded. This will reduce the risk of personal injury, fire, or
damage to the equipment. The total rack load should not exceed 80 percent
of the branch circuit rating. Consult the electrical authority having jurisdiction
over your facility wiring and installation requirements.

10
http://www.tyan.com
Equipment Power Cords
·Use only the power cords and power supply units provided with your
system. The system might have one or more power cords.
·Plug the power cord into a grounded (earthed) electrical outlet that is easily
accessible at all times.
·In all European electrical environments, you must ground the Green/Yellow
tab on the power cord. If you do not ground the Green/Yellow tab, it can
cause an electrical shock due to high leakage currents.
·Do not place objects on AC power cords or cables. Arrange them so that no
one might accidentally step on or trip over them.
·Do not pull on a cord or cable. When unplugging from the electrical outlet,
grasp the cord by the plug.
·To reduce the risk of electrical shock, disconnect all power cords before
servicing the appliance.
Equipment Batteries
·The system battery contains lithium manganese dioxide. If the battery pack
is not handled properly, there is risk of fire and burns.
·Do not disassemble, crush, puncture, short external contacts, or dispose of
the battery in fire or water.
·Do not expose the battery to temperatures higher than 60°C (140°F).
·The system battery is not replaceable. If the battery is replaced by an
incorrect type, there is danger of explosion. Replace the battery only with a
spare designated for your product.
·Do not attempt to recharge the battery.
·Dispose of used batteries according to the instructions of the manufacturer.
Do not dispose of batteries with the general household waste. To forward
them to recycling or proper disposal, use the public collection system or return
them to TYAN, your authorized TYAN partner, or their agents.
Equipment Modifications
·Do not make mechanical modifications to the system. TYAN is not
responsible for the regulatory compliance of TYAN equipment that has been
modified.

11
http://www.tyan.com
Equipment Repairs and Servicing
·The installation of internal options and routine maintenance and service of
this product should be performed by trained service technicians/personnel
who are knowledgeable about the procedures, precautions, and hazards
associated with equipment containing hazardous energy levels.
·Do not exceed the level of repair specified in the procedures in the product
documentation. Improper repairs can create a safety hazard.
·Allow the product to cool before removing covers and touching internal
components.
·Remove all watches, rings, or loose jewelry when working before removing
covers and touching internal components.
·Do not use conductive tools that could bridge live parts.
·Use gloves when you remove or replace system components; they can
become hot to the touch.
·If the product sustains damage requiring service, disconnect the product
from the AC electrical outlet and refer servicing to an authorized service
provider. Examples of damage requiring service include:
–The power cord, extension cord, or plug has been damaged.
–Liquid has been spilled on the product or an object has fallen into the
product.
–The product has been exposed to rain or water.
–The product has been dropped or damaged.
–The product does not operate normally when you follow the operating
instructions.
Instructional safeguard requirement
An instructional safeguard shall be provided to reduced the likelihood of
unintentional contact with a moving part in accordance with Clause F.5 except
that element 3 is optional.

Table of Contents
Chapter 1: Overview .....................................................................14
1.1 About the TYAN FT83-B7119..............................................14
1.2 Product Models....................................................................14
1.3Features...............................................................................15
1.4Standard Parts List..............................................................23
1.4.1 Box Contents................................................................23
1.4.2 Accessories ..................................................................23
1.5About the Product................................................................24
1.5.1 System Front View .......................................................24
1.5.2 System Rear View........................................................26
1.5.3 LED Definitions.............................................................27
1.5.4 Internal View.................................................................29
Chapter 2: Setting Up ...................................................................30
2.0.1 Before you Begin..........................................................30
2.0.2 Work Area.....................................................................30
2.0.3 Tools.............................................................................30
2.0.4 Precautions...................................................................31
2.1 Installing Motherboard Components.....................................32
2.1.1 Removing the Chassis Cover.......................................32
2.1.2 Installing the CPU, Heat sink and Air Duct...................34
2.1.3 Installing the Memory ...................................................37
2.1.4 Installing the Expansion Card (PCIE Board) ................40
2.1.5 Installing the Expansion Card (OCP Riser Card).........48
2.1.6 Installing Hard Drives ...................................................49
2.2 Rack Mounting.....................................................................51
2.2.1 Installing the Server in a Rack......................................53
Chapter 3: Replacing Pre-Installed Components......................55
3.1 Introduction..........................................................................55
3.2 Disassembly Flowchart........................................................55
3.3 Removing the Cover............................................................56
3.4 Replacing the Power Supply ...............................................56
3.5 Replacing the Front Panel Board ........................................57
3.5.1 Front Panel Board Features.............................................58
3.6 Replacing the USB Board....................................................59
3.6.1 Front Panel Board Features.............................................60
3.7Replacing the Fan Board.....................................................61
3.7.1 Fan Board Features..........................................................63
3.8Replacing the HDD Backplane Board .................................64
3.8.1 HDD Backplane Board Features......................................65
3.8.2 Connector Definition.........................................................66
3.9Replacing PCIE Board.........................................................67

13
http://www.tyan.com
3.9.1 PCIE Board Features .......................................................68
3.10 Replacing the IO Bridge Board..........................................70
3.10.1 IO Bridge Board Features...............................................71
3.11 Replacing the Rear IO Board..............................................72
3.11.1 Rear IO Board Features.................................................74
3.12 Replacing the OCP Riser Card .........................................75
3.12.1 OCP Riser Card Features ..............................................76
3.13Replacing the Motherboard.................................................77
Chapter 4: Motherboard Information ..........................................80
4.1 Board Image........................................................................81
4.2 Block Diagram .....................................................................82
4.3 Motherboard Mechanical Drawing.......................................83
4.4 Board Parts, Jumpers and Connectors ...............................84
4.5 Thermal Interface Material...................................................91
4.6 Tips on Installing Motherboard in Chassis ..........................92
4.7 Installing the Memory ..........................................................94
4.8 Finishing Up.........................................................................98
Chapter 5: BIOS Setup..................................................................99
5.1 About the BIOS..................................................................99
5.2 Main Menu........................................................................101
5.3 Advanced Menu...............................................................102
5.4 Platform Configuration ...................................................140
5.5 Socket Configuration ......................................................150
5.6Server Management..........................................................177
5.7 Security..............................................................................181
5.8 Boot ...................................................................................186
5.9 Save & Exit........................................................................189
Read only .....................................................................................190
Chapter 6: Diagnostics...............................................................191
6.1 Flash Utility........................................................................191
6.2 AMIBIOS Post Code (Aptio)..............................................192
Appendix I: How to recover UEFI BIOS ....................................202
Appendix IV: Fan and Temp Sensors .......................................204
Appendix V: Cable Connection Tables.....................................209
Appendix VI: FRU Parts Table...................................................212
Appendix VII: Glossary...............................................................214
Appendix VII: Technical Support...............................................220

14
http://www.tyan.com
Chapter 1: Overview
1.1 About the TYAN FT83-B7119
Congratulations on your purchase of the TYAN®FT83-B7119, a highly optimized
rack-mountable 4U barebone system. FT83-B7119 is designed to support dual
Intel®Xeon®Scalable Processor Families and up to 768GB RDIMM / 1536GB
LRDIMM / 3072GB RDIMM 3DS / LRDIMM 3DS, providing a rich feature set and
incredible performance. Leveraging advanced technology from Intel®,
FT83-B7119 server system is capable of offering scalable 32 and 64-bit computing,
high-bandwidth memory design, and lightning-fast PCI-E bus
implementation.FT83-B7119 not only enpowers your company in today’s
demanding IT environment but also offers a smooth path for future application
usage.
TYAN®also offers the FT83-B7119 in a version that can support up to twelve (12)
or twenty-four (24) 2.5”/3.5”hot-swap SATA 6G HDDs. FT83-B7119 uses
rack-mountable 4U chassis featuring a robust structure and a solid mechanical
enclosure. All of this provides FT83-B7119 the power and flexibility to meet the
needs of nearly any server application.
1.2 Product Models
The system board within the Tyan Barebone is defined by the following models:
B7119F83V12HR-2T-N: Intel-based platform
B7119F83V24HR-2T-N: Intel-based platform

15
http://www.tyan.com
1.3Features
B7119F83V12HR-2T-N Specifications
System
Form Factor
4U Rackmount
Chassis Model
FT83
Dimension (D x W x H)
32.68" x 17.25" x 6.93" (830 x 438.4
x 176mm)
Motherboard Name
S7119GMRE #
Motherboard
Notification
# The motherboard not sold
separately
Gross Weight
43.5 kg (95.9 lbs)
Net weight
27.5 kg (60.6 lbs)
Front Panel
Buttons
(1) RST, (1) PWR w/ LED, (1) UID
LEDs
(1) ID, (3) LAN, (1) System Event
I/O Ports
(1) VGA port, (2) USB 3.0 ports, (1)
COM Port
External Drive Bay
Q'ty / Type
(12) 3.5"/2.5" Hot-Swap SSD/HDD
HDD Backplane
Support
SAS 12Gb/s, SATA 6Gb/s, NVMe
Supported HDD
Interface
(12) SATA 6Gb/s
System Cooling
Configuration
Redundancy
Yes
FAN
(5+1) hot-swap 12cm fans
Power Supply
Type
RPSU
Input Range
AC 100-127V/13A ,
AC 200-240V/9.5A
Frequency
50-60 Hz
Output Watts
4,000 Watts (100-127Vac input),
4,800Watts (200-240Vac input)
Efficiency
PFC, 80 plus Platinum
Redundancy
3+1
NOTE: When use 100-127V AC
input, the system does not support
redundant PSU operation.
Altitude 5000m
Processor
Q'ty / Socket Type
(2) LGA3647
Supported CPU
Series
Intel Xeon Scalable Processor, 2nd
Gen Intel Xeon Scalable Processor

16
http://www.tyan.com
Thermal Design
Power (TDP) Wattage
Max up to 205W
System Bus
Up to 10.4/9.6 GT/s with Intel
UltraPath Interconnect (UPI)
support
Chipset
PCH
Intel C621
Switch IC
(2) PLX PEX8796
Memory
Supported DIMM
Qty
(12)+(12) DIMM slots
DIMM Type / Speed
DDR4 RDIMM/RDIMM
3DS/LRDIMM/LRDIMM 3DS
2933/2666, DDR4 JEDEC NVDIMM
2666, Intel Optane DC Persistent
Memory Module (DCPMM)
Capacity
Up to 768GB RDIMM/ 1,536GB
LRDIMM/ 3,072GB RDIMM
3DS/LRDIMM 3DS *Follow latest
Intel DDR4 Memory POR
Memory channel
6 Channels per CPU
Memory voltage
1.2V
Notification
DDR4-2933 speed only supported
with 2nd Gen Intel Xeon Scalable
Processor (codename: Cascade
Lake) and in a 1 DIMM per channel
configuration., Intel Optane DC
Persistent Memory Module
(DCPMM) only supported with
specific 2nd Gen Intel Xeon Scalable
Processor (codename: Cascade
Lake). Please contact Tyan
Technical Support for more detail.
Expansion Slots
PCI-E
(1) PCI-E Gen3 x16 slot (FH, FL,
SW), (10) PCI-E Gen3 x16 slots (FH,
FL, DW)
Pre-install TYAN
Riser Card
(PCI-E Gen3)
(1) M2217-L16-IO # riser card for (1)
storage mezz. slot
Pre-install TYAN
Mezz. Card
(PCI-E Gen3)
(1) M7108-X550-2T LAN mezz. card
w/ (2) 10GbE ports (deployed on (1)
PCI-E Gen3 x16 OCP 2.0 slot)
Others
(1) PCI-E Gen3 x16 OCP 2.0 slot
(conn.A+conn.B), (1) PCI-E Gen3
x16 storage mezz. slot
Notification
# The item not sold separately

17
http://www.tyan.com
LAN
Q'ty / Port
(2) 10GbE ports, (1) GbE port
dedicated for IPMI
Controller
Intel X550-BT2
PHY
Realtek RTL8211E
Storage
SATA
Connector
(2) Mini-SAS HD (8-ports)
Controller
Intel C621
Speed
6Gb/s
RAID
RAID 0/1/10/5 (Intel RSTe)
sSATA
Connector
(2) SATA-III, (1) Mini-SAS HD
(4-ports)
Controller
Intel C621
Speed
6Gb/s
RAID
RAID 0/1/10/5 (Intel RSTe)
Graphic
Connector type
D-Sub 15-pin
Resolution
Up to 1920x1200
Chipset
Aspeed AST2500
I/O Ports
USB
(2) USB3.0 ports (@ rear), (2)
USB3.0 ports (@ front)
COM
(1) DB-9 COM port (at front)
VGA
(1) D-Sub 15-pin port (at front)
RJ-45
(2) 10GbE ports, (1) dedicated
GbE for IPMI
TPM (Optional)
TPM Support
Please refer to our TPM
supported list.
System Monitoring
Chipset
Aspeed AST2500
Temperature
Monitors temperature for CPU &
memory & system environment
Voltage
Monitors voltage for CPU,
memory, chipset & power supply
LED
Over temperature warning
indicator, Fan & PSU fail LED
indicator
Others
Watchdog timer support
Server Management
Onboard Chipset
Onboard Aspeed AST2500
AST2500 iKVM
Feature
24-bit high quality video
compression, Supports storage
over IP and remote platform-flash,
USB 2.0 virtual hub

18
http://www.tyan.com
AST2500 IPMI
Feature
IPMI 2.0 compliant baseboard
management controller (BMC),
10/100/1000 Mb/s MAC interface
BIOS
Brand / ROM size
AMI, 32MB
Feature
Hardware Monitor, SMBIOS
3.0/PnP/Wake on LAN, Boot from
USB device/PXE via LAN/Storage,
User Configurable FAN PWM Duty
Cycle, Console Redirection, ACPI
sleeping states S4,S5, ACPI 6.1
Operating System
OS supported list
Please refer to our AVL support
lists.
Regulation
FCC (SDoC)
Class A
CE (DoC)
Class A
CB/LVD
Yes
RCM
Class A
VCCI
Class A
Operating Environment
Operating Temp.
10°C ~ 35°C (50°F~ 95°F)
Non-operating Temp.
- 40°C ~ 70°C (-40°F ~ 158°F)
In/Non-operating
Humidity
90%, non-condensing at 35°C
Note
Please refer to the TYAN NVIDIA
Compatibility List for the operating
temperature while GPGPU
deployed
RoHS
RoHS 6/6 Compliant
Yes
Package Contains
Barebone
(1) FT83-B7119 w/NV Tesla-aware
FW Barebone
Manual
(1) Quick Installation Guide

19
http://www.tyan.com
B7119F83V24HR-2T-N Specifications
System
Form Factor
4U Rackmount
Chassis Model
FT83
Dimension (D x W x H)
32.68" x 17.25" x 6.93" (830 x 438.4
x 176mm)
Motherboard Name
S7119GMRE #
Motherboard
Notification
# The motherboard not sold
separately
Gross Weight
43.5 kg (95.9 lbs)
Net weight
27.5 kg (60.6 lbs)
Front Panel
Buttons
(1) RST, (1) PWR w/ LED, (1) UID
LEDs
(1) ID, (3) LAN, (1) System Event
I/O Ports
(1) VGA port, (2) USB 3.0 ports, (1)
COM Port
External Drive Bay
Q'ty / Type
(24) 3.5"/2.5" Hot-Swap SSD/HDD
HDD Backplane
Support
SAS 12Gb/s, SATA 6Gb/s, NVMe
Supported HDD
Interface
(24) SATA 6Gb/s
Notification
The SAS/SATA HDD backplane is
connected to onboard SATA
connection by default. Please
contact Tyan technical support if a
discrete SAS HBA/RAID adapter
installed is required.
System Cooling
Configuration
Redundancy
Yes
FAN
(5+1) hot-swap 12cm fans
Power Supply
Type
RPSU
Input Range
AC 100-127V/13A ,
AC 200-240V/9.5A
Frequency
50-60 Hz
Output Watts
4,000 Watts (100-127Vac input),
4,800Watts (200-240Vac input)
Efficiency
PFC, 80 plus Platinum
Redundancy
3+1
NOTE: When use 100-127V AC
input, the system does not support
redundant PSU operation.
Altitude
5000m

20
http://www.tyan.com
Processor
Q'ty / Socket Type
(2) LGA3647
Supported CPU
Series
Intel Xeon Scalable Processor, 2nd
Gen Intel Xeon Scalable Processor
Thermal Design
Power (TDP) Wattage
Max up to 205W
System Bus
Up to 10.4/9.6 GT/s with Intel
UltraPath Interconnect (UPI)
support
Chipset
PCH
Intel C621
Switch IC
(2) PLX PEX8796
Memory
Supported DIMM
Qty
(12)+(12) DIMM slots
DIMM Type / Speed
DDR4 RDIMM/RDIMM
3DS/LRDIMM/LRDIMM 3DS
2933/2666, DDR4 JEDEC NVDIMM
2666, Intel Optane DC Persistent
Memory Module (DCPMM)
Capacity
Up to 768GB RDIMM/ 1,536GB
LRDIMM/ 3,072GB RDIMM
3DS/LRDIMM 3DS *Follow latest
Intel DDR4 Memory POR
Memory channel
6 Channels per CPU
Memory voltage
1.2V
Notification
DDR4-2933 speed only supported
with 2nd Gen Intel Xeon Scalable
Processor (codename: Cascade
Lake) and in a 1 DIMM per channel
configuration., Intel Optane DC
Persistent Memory Module
(DCPMM) only supported with
specific 2nd Gen Intel Xeon Scalable
Processor (codename: Cascade
Lake). Please contact Tyan
Technical Support for more detail.
Expansion Slots
PCI-E
(1) PCI-E Gen3 x16 slot (FH, FL,
SW), (10) PCI-E Gen3 x16 slots (FH,
FL, DW)
Pre-install TYAN
Riser Card
(PCI-E Gen3)
(1) M2217-L16-IO # riser card for (1)
storage mezz. slot
Pre-install TYAN
Mezz. Card
(PCI-E Gen3)
(1) M7108-X550-2T LAN mezz. card
w/ (2) 10GbE ports (deployed on (1)
PCI-E Gen3 x16 OCP 2.0 slot)
Others
(1) PCI-E Gen3 x16 OCP 2.0 slot