TypeS AC530013 User manual

Jump Starter & Portable Power Bank
with Wireless Charging
WP ITM. AC530013
User Manual
BC

2
5.94 × 3.3 × 1.26 in (151 × 84 × 32 mm)
0.96 lbs (434g)
Lithium-Ion
Up to 8000mAh (3.7V)
29.6 Wh
5V 2A
5V 2.4A
9V 2A / 5V 2.6A
10W (max.)
200A - 350A
-20ºC ~ 34ºC (-4ºF ~ 93ºF)
-20ºC ~ 40ºC (-4ºF ~ 104ºF) Avg. Temp.
0ºC ~ 40ºC (32ºF ~ 104ºF)
4-5 hours
IP64 Splash-Resistant (w/ Ports Covered)
Product Dimensions:
Product Weight:
Internal Battery:
Capacity:
Watt Hours:
Input (Micro USB / USB-C):
USB-A Output:
USB-C Output:
Qi Wireless Charging Rating:
Jump Start Current:
Operating Temperature:
Storage Temperature:
Charging Temperature:
Charging Time:
Housing Protection:
TECHNICAL SPECIFICATIONS:
FEATURE OVERVIEW :
1. USB-A Output
2. LED Flashlight, Strobe & Hazard Modes
3. Micro USB Charge Input
4. USB-C Output / Input
5. Jumper Cables Port
6. Safe & Smart Polarity & Overcharge Protection
7. Mode Button: Power, LED & Language Selection
8. LCD Display
9. Battery Level
10. Wireless Charging Pad
11. Jumper Cables
12. Negative Clamp (Black)
13. Positive Clamp (Red)
14. Polarity Circuit Protection Box w/ LED Indicators
9 8
7
1
26
3 4
5
12
13
11 14
10

3
PACKAGE CONTENTS:
Jump Starter
Power Bank
12V USB Charger &
Micro USB
Charging Cable
Storage Case Safe & Smart
Jumper Cables
Press the Mode Button to check the
capacity of the Jump Starter.
CHECKING THE POWER LEVEL
NOTE: Fully charge the Jump Starter upon receipt. Check battery status periodically and recharge every
2-3 months and after every use to maintain the efciency and to prolong the life of the internal battery.
CHARGING THE JUMP STARTER:
At home:
1. Plug included Micro USB Charging Cable into a USB-A port on a computer or
2A USB wall adapter (not included).
2. Connect the Micro USB Charging Cable into the Micro USB Charge Input Port
on the Jump Starter.
3. Disconnect the Jump Starter when it is fully charged. Store the Jump Starter in
a safe place when not in use.
In Car:
1. Plug included Micro USB Charging Cable into included 12V USB Charger then
connect to 12V socket in vehicle.
2. Connect the Micro USB Charging Cable into the Micro USB Charge Input Port
on the Jump Starter.
3. Disconnect the Jump Starter when it is fully charged. Store the Jump Starter in
a safe place when not in use.
NOTE: In order to reduce the
risk of re or electric shock, an
adapter shall be chosen that is
suitable for the application and
is certied as a Class 2 or LPS
power supply or power adapter.
When charging, the battery indicator will glow.
Jump Starter is fully charged when the battery
indicator is solid and reads 100%.

4
Press the power button once to enable
wireless charging function. Place the
device on top of wireless charging
icon to start. LCD screen is ON while
wireless charging is in progress. The
power level will vary during charging.
You may need to adjust the orientation
to have the best charging.
NOTE: The wireless charging feature only works on devices
that allow Qi (inductive) wireless charging. Only use the wireless
charging pad with Qi-certied devices.
WIRELESSLY CHARGING YOUR MOBILE DEVICES:
We recommend using the original charging cable that came with
your mobile device, or an approved cable certied by the mobile
device manufacturer. Two mobile devices can be charged at the
same time by utilizing both the
USB-A and USB-C Output ports.
To begin charging, press the
Mode Button once. While
charging, press the Mode Button
to check the battery capacity.
CHARGING YOUR MOBILE DEVICES:

5
Black Red
1. Press the Mode Button to power on the
Jump Starter; ensure the power level is
50% or higher.
2. Insert the GRAY end of the Jumper Cables
into the Jumper Cables Port. The LCD
Display will read: Clamp cables to battery.
JUMP STARTING:
BEFORE YOU JUMP START!
Before you attempt to jump start your vehicle, ensure your vehicle is
in Park. Ensure manual transmission vehicles are in Neutral with the
Emergency Brake engaged.
The Cable Clamps are color-coded, RED for
POSITIVE (+) and BLACK for NEGATIVE (-).
DO NOT mix up the cables or allow the metal
ends to touch together because this may
damage the battery, charging system and/or
electronics on a vehicle.
Locate the vehicle battery and follow the steps below. We recommend
jump starting when the Jump Starter battery level is > 50%.
INTELLI-STEP SMART DISPLAY:
The Jump Starter is programmed to display step-by-step instructions to
Jump Start your vehicle. When the Jump Starter is powered on, plug the
Jumper Cables into the Jumper Cables Port and follow the progressive
prompts on the LCD Display. The detailed steps are provided in the next
section for reference.
JUMP STARTING:
Black
Red

6
Black
Red
JUMP STARTING CONT.:
3. Connect the RED clamp to the POSITIVE
(+) post on the car battery. The
POSITIVE battery post will be slightly
larger than the NEGATIVE post, and will
be marked with a PLUS (+) sign. There
may also be a RED plastic protective
cover over the positive battery post.
4. Connect the BLACK clamp to the NEGATIVE (-) post on the car battery.
The NEGATIVE will be marked with a MINUS (-) sign. There may be a
BLACK plastic protective cover over the negative battery post.
NOTE: Do not connect the RED clamp (+) and the BLACK
clamp (-) at the same time. Connect the RED clamp rst, then the
BLACK clamp.
CAUTION: DO NOT lean directly over the battery while making jumper
connections.
5. Check the LED status on the Polarity Circuit Protection Box. Proceed to
the next step unless the LED is ashing RED and BEEPING. Reference
Polarity Protection Circuit Status chart in the next section.
6. Once the clamps are properly connected to the vehicle battery, the LCD
Display will read: Ready, Start vehicle ignition. You have 90 seconds to
start your vehicle before the Jump
Starter shuts off in order to prevent
the vehicle battery from reverse
charging the unit.
NOTE: If vehicle does not crank, or cranks very slowly, wiggle the
cable clamps on the vehicle battery to ensure they are making good
contact. Wait 60 seconds before trying to jump start your vehicle again.
Each new jump start attempt requires disconnection of both
clamps from the vehicle battery and reconnection.

7
The engine should start if there are no other problems (such as a bad
starter or ignition circuit problem). Do not attempt to jump start the
vehicle more than 3 times with the Jump Starter. If the vehicle fails to
start after 3 attempts, it is likely due to alternative reasons that should
be checked by an auto mechanic.
7. When the engine starts, the LED on the Polarity Circuit Protection
Box will blink RED and
beep. The LCD Display will
also read: Successful jump,
unplug cables.
8. Disconnect the cables from your vehicle within 30 seconds. First
remove the RED/POSITIVE (+) clamp and then the BLACK/
NEGATIVE (-) clamp.
9. Do not allow the metal ends of the jumper cable clamps to touch each
other, or the RED clamp to touch anything metal on the car. Now
unplug the
GRAY end of the jumper cables from the Jump Starter.
This will reset the jumper cables. In 30-seconds the jump starter will
power off automatically.
10. Keep the engine running for 20 to 30 minutes, or drive the car to
recharge the battery.
NOTE: If the engine dies shortly after it has been jump started, or
as soon as the jumper cables are disconnected, it probably means
the vehicle charging system is not working (bad alternator, voltage
regulator, wiring problem, or loose/ dirty battery cables). Please seek
professional help from an auto mechanic to nd the root cause of the
problem. The Jump Starter may not work correctly for vehicles that
require remote battery jumper locations (e.g.: battery located in trunk
or other location). Please consult the owner’s manual for your vehicle.
JUMP STARTING CONT.:

8
Message on LCD Screen Message Meaning
Low Power, charge at least 50% Jump Starter battery below 50%
Battery Protected, Unplug, Start over Wrong connection
Device is too hot, Cool before use
Temperature of jump starter is above 55°C
JUMP STARTING CONT.:
Polarity Protection Circuit Status
Solid LED On Flashing LED LED Off
Status (Light & Sound Indicator)
Status Meaning:
Red Light Green Light Sound
None The car battery is ready for jump start.
None The Jump Starter needs to be charged.
None The car battery is ready for jump start. If
the indicator doesn’t turn solid Green, the
car battery voltage is higher than the jump
starter. You can still jump start your battery,
but may need to charge your jump starter.
Beeping Disconnect the jumper cables from the car
battery and jump starter. Either the car jump
start is complete or there is a connection
problem.
None This status shows after 90 seconds time out.
Disconnect the jumper cables from the car
battery and jump starter to reset. Reconnect
the jumper cables to jump start the vehicle.
None Please contact TYPE S for troubleshooting.

9
Function Action Remarks
Turn on the jump
starter
Press the Mode Button
Switch language to
Spanish
Press and hold the Mode
Button for 5 seconds
until the word “English”
is shown on the LCD
screen, then press button
once to enter Spanish
mode.
LED light remains on from 3s
till 5s, light turned off when
the word “English” is shown
on the LCD screen. Remain in
Spanish mode if product is idle
for 10 seconds.
Switch language to
French
Press once while in
Spanish mode
Remain in French mode if
product is idle for 10 seconds
Switch language to
Japanese
Press once while in
French mode
Remain in Japanese mode if
product is idle for 10 seconds
Switch language to
Korean
Press once while in
Japanese mode
Remain in Korean mode if
product is idle for 10 seconds
Switch language to
English
Press once while in
Korean mode
Remain in English mode if
product is idle for 10 seconds
Conrm and turn off
language setting
Press and hold the Mode
Button for 5 seconds
LED light remains on from 3s
till 5s, light turned off after 5s.
LANGUAGE SELECTION:
LED LIGHT:
Flashlight Press and hold the power button for three seconds.
Strobe Light Press once while in ashlight mode
Hazard Light Press once while in strobe light mode
Turn Off Press and hold the power button for three seconds.

10
INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS
• Always wear safety glasses when jump starting a battery (to protect your
eyes), and gloves when handling a battery (to protect your hands).
• When jump starting a vehicle please ensure that the gray plug is securely
tted into the jump starter socket on the jump starter.
• Ensure the battery clamps are connected correctly, and the connectors are
free from rust and dirt.
• Do not allow this product to become wet. Exposure to excessive moisture
will damage the unit.
• Do not immerse the product in water.
• Do not operate the product in explosive atmospheres, such as in the
presence of ammable liquid, gas or dust.
• Do not modify or disassemble this product.
• Do not store in locations where the temperature may exceed 104ºF (40ºC).
• Charge only using the charger provided.
• Under extreme heat conditions, battery leakage may occur. Avoid contact
with your skin. In case of skin or eye contact, rinse immediately with clean
water and seek medical attention.
• If battery leakage occurs, take it to your local battery recycling center for
disposal. Do not attempt to use.
• This car jump starter is for use with 12V vehicles only. Using on non-12V
vehicles may cause serious damage to the vehicle, jump starter, or injury
to the user. Refer to the owner’s manual for the vehicle if you are uncertain
what voltage the vehicle runs on.
BATTERY DISPOSAL
The battery is self-contained and not consumer replaceable. The battery must
be disposed of properly when it no longer holds a charge. Proper charging
practices will increase the life of the product. For information on battery
recycling, call toll-free 800-822-8837.
For information regarding air travel safety with batteries please check the U.S.
Department of Transportation prior to travel at:
http://phmsa.dot.gov/safetravel/batteries
or contact your airline if traveling from a country outside the U.S.
Note: The Car Jump Starter contains the equivalent of 2.4g of lithium and
gives 29.6 watt hours of power.
WARNING: