U-Line TORNADO H-10166 User manual

PAGE 1 OF 8 0822 IH-10166
H-10166
TORNADO®LIGHTWEIGHT
COMMERCIAL VACUUM
1-800-295-5510
uline.com
SAFETY
Para Español, vea páginas 9-16.
Pour le français, consulter les pages 17-24.
TOOLS NEEDED
Phillips Screwdriver Flathead Screwdriver
GROUNDING
WARNING! This appliance must be grounded.
If it should malfunction or break down,
grounding provides a path of least resistance
for electric current to reduce the risk of electric
shock. This machine is equipped with a cord
having an equipment-grounding conductor
and grounding plug. The plug must be inserted
into an appropriate outlet that is properly
installed and grounded in accordance with all
local codes and ordinances.
WARNING! Improper connection of the
equipment-grounding conductor can result in
a risk of electric shock. Check with a qualified
electrician or service person if you are in
doubt as to whether the outlet is properly
grounded. Do not modify the plug provided
with the appliance – if it will not fit the outlet,
have a proper outlet installed by a qualified
electrician.
• Read and understand all instructions before using
this unit.
• This appliance is for use on a nominal 115-volt
circuit and has a grounding plug.
• Use this unit only as described in these instructions.
Use only manufacturer's recommended
attachments. To reduce the risk of personal
injury or damage to unit, use only Tornado®
recommended accessories.
• This vacuum is intended for commercial use
only. It is designed exclusively to pick up dirt, dry
debris and dust in an indoor environment and is
not constructed for any other use. The pickup of
any type of fluid or dangerous/toxic materials is
prohibited. Use only recommended accessories.
WARNING! To reduce the risk of fire, electric
shock or injury, do not leave appliance
unattended when plugged in. Unplug from
outlet when not in use and before servicing.
WARNING! Electric shock could occur if used
outdoors or on wet surfaces.
• Do not allow to be used as a toy. Close attention
is necessary when used by or near children.
• Do not use with damaged cord or plug. If
appliance is malfunctioning, has been dropped,
damaged, left outdoors or dropped into water, call
Uline Customer Service at 1-800-295-5510.
• Do not pull or carry by cord, use cord as handle,
close a door on cord, or pull cord around sharp
edges or corners. Do not run appliance over cord.
Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp
the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Turn off all controls before unplugging.
• Do not block or put any object into openings. Keep
openings free of dust, lint, hair and anything that
may reduce airflow.

PAGE 2 OF 8 0822 IH-10166
SAFETY CONTINUED
ASSEMBLY
• Keep hair, loose clothing and body parts away
from openings and moving parts.
• Do not pick up anything that is burning or smoking,
such as cigarettes, matches or hot ashes.
• Do not use without vacuum bag and/or filters
in place.
• Use extra care when cleaning stairs.
• Do not use to pick up flammable or combustible
liquids such as gasoline or use in areas where they
may be present.
• Connect to a properly grounded outlet only.
• This vacuum is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
vacuum by a person responsible for their safety.
• Keep children and unauthorized persons away
from the machine when in use.
WARNING! Plastic bags or film can be
dangerous. To avoid danger of suffocation,
keep away from babies and children.
1. Slide handle tube into
the connector, aligning
the hole in the handle
tube with hex-shaped
cavity at the top of the
connector.
(See Figure 1)
2. Hold the hex nut in the
hex-shaped cavity on
back of connector
with finger. Insert screw
and thread into hex
nut. Continue to hold
hex nut in place and
tighten screw with a
Phillips screwdriver.
Do not overtighten.
(See Figure 2)
3. Slide screw through
plastic cord hook from
inside cloth bag. Align
screw with hole in
handle tube. Tighten
screw. (See Figure 3)
4. Remove screw from filter cover. Lift filter and cover
away from vacuum. (See Figure 4)
5. Insert the connector plug into the back of the unit at
the rear of the base. (See Figure 5)
IMPORTANT! Ensure the connector plug is fully
inserted.
6. Replace filter and filter cover. Secure with previously
removed screw.
Figure 1
Figure 2
Figure 5
Figure 3
Figure 4

PAGE 3 OF 8 0822 IH-10166
OPERATION
POWER SUPPLY
STOP! Before using, ensure the connector plug
is securely attached to the base and that the
power plug is plugged into a polarized outlet.
NOTE: Always unplug the vacuum by grasping
the power source plug (not the power cord)
and disconnecting from the outlet.
The power cord is stored at the back of the vacuum
and is looped around the quick release cord hooks.
The plug is designed to attach to the power cord
during storage.
POWER SWITCH
The power switch is located
in the handle of the
vacuum. (See Figure 6)
• Push down (I) to turn on.
• Push up (O) to turn off.
POWER CORD STORAGE
When finished using vacuum, return it to the upright
position. Ensure vacuum is turned off.
NOTE: Always unplug the vacuum by grasping
the power source plug (not the power cord)
and disconnecting from the outlet.
Wind the cord around
the quick release cord
hooks on the back of the
vacuum, or hang on the
cord storage hook on the
front of the vacuum. Attach
the plug end to the power
cord. (See Figure 7)
VACUUM USE
This vacuum is designed to effectively and safely clean
all types of carpeting, wood, linoleum and vinyl floors.
To place vacuum in position for use, lightly press foot on
the base and pull the handle backward.
(See Figure 8)
Figure 6
Figure 8
Figure 7
Cord
Storage
Hook

PAGE 4 OF 8 0822 IH-10166
ROUTINE MAINTENANCE
For maximum performance, check and maintain
vacuum parts regularly.
WARNING! To avoid electrical shock or
injury from moving parts, always turn off the
power switch and unplug the power source
plug before performing maintenance or
troubleshooting.
IMPORTANT! Always unplug by grasping the
power source plug. Never pull on the power
cord to unplug.
NOTE: Vacuuming new carpet or vacuuming
fine powders may clog the dust bag. Check
dust bag often.
REPLACING THE DUST BAG
IMPORTANT! Check dust bag weekly. Replace
dust bag when it is near full or when cleaning
suction diminishes. Never reuse a dust bag.
1. Unplug vacuum by grasping and pulling on the
power source plug.
2. Unzip cloth bag. Unlock collar retainer by pressing
on the two tabs and pulling the top toward user.
Dispose of used dust bag. (See Figure 9)
3. Slide collar of new dust bag completely into collar
retainer. (See Figure 10)
4. Push collar retainer
back into position
and secure in place.
(See Figure 11)
5. Tuck the remainder
of the dust bag
completely inside
the cloth bag.
Ensure it lays flat,
top to bottom,
without bunching.
Zip cloth bag.
MAINTENANCE
Figure 9
Collar Retainer
Figure 10
F i g u re 11

PAGE 5 OF 8 0822 IH-10166
MAINTENANCE CONTINUED
CLEANING THE DUST TUBE
The vacuum features a dust tube designed to optimize
cleaning power. For best performance, routinely check
and clear excess dust and other debris.
WARNING! To avoid electrical shock or
injury from moving parts, always turn off the
power switch and unplug the power source
plug before performing maintenance or
troubleshooting. Always unplug by grasping
the power source plug. Never pull on the
power cord to unplug.
NOTE: Cover floor with newspaper to catch
any loose material or dust removed during
cleaning.
1. Release bag tension spring. (See Figure 12)
2. Remove filter cover screw, filter cover and filter.
(See Figure 13)
3. Unplug connector plug. (See Figure 14)
4. Lift dust tube (A) while
pressing the tube
release button (B)
located under the
rubber collar. Tube
release button can be
pressed through the
rubber collar (C).
(See Figure 15)
5. Use a wire brush to
clean out the inside of
the dust tube (A) and
the top section of the
base (D). (See Figure 15)
6. Align tube release button on the tube and rubber
collar. Reconnect tube with the base. Ensure that
tube snaps securely in place.
7. Replace connector plug back into base of vacuum.
8. Replace filter and filter cover. Secure with previously
removed screw.
Figure 12
Figure 13 Fig ure 14
Figure 15
B
A
D
C

PAGE 6 OF 8 0822 IH-10166
CLEANING BRUSH/REPLACING DRIVE BELT
Check rotating cleaning brush and drive belt regularly
for wear or damage.
NOTE: Keep rotating cleaning brush ends free
of string, hair and carpet fibers.
NOTE: The rotating cleaning brush can most
often be cleaned without removal from the
vacuum. If there is an excessive amount of hair
and/or debris, remove the rotating cleaning
brush for proper cleaning.
1. Unplug the vacuum and turn face down on a flat
surface.
2. Remove all three screws from the bottom of the base.
(See Figure 16)
3. Grip both the top cover and base while turning unit
back over. Lift off top cover.
4. Check drive belt. If broken or damaged, remove
rotating cleaning brush and replace drive belt.
(See Figure 17)
5. To remove the
rotating cleaning
brush, pull the right
side of the brush
toward the front of
the base and lift
slowly. (See Figure 18)
6. Remove drive belt
from cleaning
brush and clean as
necessary.
7. Place existing or new drive belt over rotating
cleaning brush and motor shaft. Insert the end cap
pin on the left end of the rotating cleaning brush
into the slot on the base. Slide the end cap pin on
the right end of the rotating cleaning brush into the
slot in the base and lower until it clicks into place.
(See Figure 19)
8. Ensure furniture protection guard is in proper place.
(See Figure 19)
9. Place top cover onto base. Press into place,
ensuring furniture protection guard is on the outside.
10. Reinstall previously removed screws beginning with
the center screw.
MAINTENANCE CONTINUED
Figure 16
Figure 18
Fi gu re 17
Drive Belt
Figure 19
Slot
Slot
Furniture Protection Guard

PAGE 7 OF 8 0822 IH-10166
MAINTENANCE CONTINUED
CLEANING THE FILTER
The post-motor HEPA filter is located in the base of the
vacuum.
NOTE: Filter should be checked often and
cleaned when it becomes dirty.
1. Remove screw on filter
cover with a Phillips
head screwdriver. Lift
off filter cover.
(See Figure 20)
2. Remove post-motor
HEPA filter. Blow out filter
with air and reinstall.
3. Replace filter cover.
Secure with previously
removed screw.
REPLACING LIGHT BULB
1. Unplug the vacuum.
2. Insert a flathead screwdriver into slot and remove
light lens. (See Figure 21)
3. Grasp bulb and pull out. Discard old bulb and
replace with new one. (See Figure 22)
4. Replace light lens.
Figure 20
Figure 21
Figure 22

PAGE 8 OF 8 0822 IH-10166
TROUBLESHOOTING
1
-800-295-551
0
uline.com
OPERATING ISSUE CAUSES RECOMMENDATIONS
Vacuum won't run. Vacuum is not plugged in.
Household fuse/circuit breaker
tripped.
Check power source, plug and
connector.
Check/replace fuse –reset breaker.
Vacuum won't pick up dirt. Dust bag is full.
Drive belt is not functioning.
Rotating cleaning brush bristles are
worn.
Rotating cleaning brush is jammed.
Dust tube is clogged.
Replace with new dust bag.
Realign or replace drive belt.
Replace rotating cleaning brush.
Remove rotating cleaning brush
and clean debris from brush ends.
Clean dust tube.
Dust bag is clogged or dirty. Dust bag is full.
Dust bag collar retainer is not secure.
Inlet is clogged.
Replace with new dust bag.
Secure dust bag collar retainer.
Shake dust to bottom of
dust bag.
If the troubleshooting section does not resolve the problem, contact Uline Customer Service at 1-800-295-5510.