U-Line Echelon Wine Captain 2075WC User manual

www.U-LineService.com
Phone [phone] • FAX [phone]
Service & Parts Tech Lines Phone [phone] • FAX [phone]
[email protected]
©2005 U-Line Corporation
02/2005
2075WC Wine Captain®
and 2075WCOL Wine Captain®
with Overlay
Installation Guide
™

2075WC/2075WCOL Wine Captain®
www.U-LineService.com 202/2005
™
Contents
Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Cut-Out Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Product Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Door Swing/Clearances Information . . . . . . . . . . . . . . 5
Reversing the Door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Other Site Requirements . . . . . . . . . . . . . . . . . . . . . . . . 6
Side-By-Side Installation Instructions . . . . . . . . . . . . . . 7
Adding a Final Finish Coat to Wood Trim . . . . . . . . . . . 7
Staining Wood Trim a Different Color . . . . . . . . . . . . . 8
Overlay Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Checking Door Alignment . . . . . . . . . . . . . . . . . . . . . . 12
Adjusting Door Alignment . . . . . . . . . . . . . . . . . . . . . . 12
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 13
Leveling Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Installation Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Anti-Tip Bracket Installation . . . . . . . . . . . . . . . . . . . . . 14
Installation Troubleshooting . . . . . . . . . . . . . . . . . . . . . 15
Initial Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Start-Up Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 15
Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
IMPORTANT
PLEASE READ all instructions completely before
attempting to install or operate the unit.
• This unit requires connection to a grounded (three-
prong), polarized receptacle that has been placed by a
qualified electrician in accordance with applicable
electrical codes.
Safety Alert Definitions
Safety items throughout this guide are labeled with a
Danger, Warning or Caution based on the risk type:
DANGER
Danger means that failure to follow this safety
statement will result in severe personal injury or
death.
WARNING
Warning means that failure to follow this safety
statement could result in serious personal injury,
or death.
CAUTION
Caution means that failure to follow this safety statement
may result in minor or moderate personal injury, property
or equipment damage.
1 Follow Safety Precautions

02/2005 3www.U-LineService.com
™2075WC/2075WCOL Wine Captain®
General Precautions
Use this appliance for its intended purpose only and
follow these general precautions along with those listed
throughout this guide:
WARNING
SHOCK HAZARD — Electrical Grounding Required.
• Keep the unit unplugged throughout installation
except during testing.
• Never remove the round grounding prong from
the plug and never use a two-prong grounding
adapter.
• Never use an extension cord to connect power to
the unit.
• Always keep your working area dry.
CAUTION
• Use care when moving and handling the unit. Use
gloves to prevent personal injury from sharp edges.
• Do not lift the unit by the door or door handle.
• Do not install the unit behind closed doors or in any
way that would obstruct airflow to the front grille,
which may cause the unit to malfunction.
You have received a carton containing your 2075WC or
2075WCOL Wine Captain®with a package inside
containing a User Manual, a Product Registration Card
and an Anti-Tip Bracket Installation Kit. 2075WCOL units
are shipped with a cardboard-wrapped door and an
additional package of hardware. Complete and mail
the Product Registration Card or register online at
www.U-LineService.com. Once your unit is installed, keep
the User Manual and this Installation Guide in a safe place
for future reference.
2075WC units are Black, White or Stainless Steel. Black
and White units have a reversible door with a slightly
contoured handle across the top. Stainless Steel units are
covered with a protective coating and have been ordered
left- or right-hand hinged. The Stainless doors are not
reversible.
2075WCOL units are Black with an unattached door that
requires the construction of a 3/4-inch thick wood overlay
frame. You must determine left- or right-hand opening
before construction.
All units come with maple trim wine racks that can be
finished or stained. Please carefully follow the directions
that apply to your unit and your intended design.
Tools/Materials Required
• 7/64" Allen wrench (included in 2075WCOL hardware)
• Screwdrivers — slotted and Phillips head
• Sandpaper; low odor, water clean up, quick drying
finish; tack cloth and, if desired, water-based wood
stain and synthetic foam brush
• 3/4-inch overlay frame material, cutting tools, drill and
bits (2075WCOL units)
Inspection
Unwrap and inspect the unit on a flat, level surface
capable of supporting its entire weight.
Removing Protective Coating
(Stainless Steel Units Only)
When inspecting/installing a Stainless Steel unit, the
protective coating covering the unit must be removed
first. Start at a corner of the unit/door and pull back the
protective coating to remove it from the unit/door.
2 Inspect and Plan

2075WC/2075WCOL Wine Captain®
www.U-LineService.com 402/2005
™
After all the protective coating has been removed from
the unit/door, clean all Stainless Steel surfaces with Claire
Stainless Steel Polish and Cleaner or comparable product
or a mild detergent and warm water solution and soft
cloth. Do NOT use abrasive cleaning agents.
Note: If cleaning with mild detergent and warm water
solution and soft cloth, the unit MUST be treated with
Claire Stainless Steel Polish and Cleaner or comparable
product to prevent discoloration.
Exterior Cleaning
(As Required)
Black and White Models:
• The door, grille and cabinet may be cleaned with a mild
detergent and warm water solution. Do not use
solvent-based or abrasive cleaners. Use a soft sponge
and rinse with clean water. Wipe with a soft, clean
towel to prevent water spotting.
Stainless Steel Models:
• Stainless steel models can discolor when exposed to
chlorine gas, pool chemicals, salt water or cleaners with
bleach.
• Keep your stainless steel unit looking new by cleaning
with a good quality all-in-one stainless steel cleaner/
polish on a monthly basis. For best results use Claire
Stainless Steel Polish and Cleaner, which can be
purchased from U-Line Corporation. (The part number
is 173348.) Comparable products are acceptable.
Frequent cleaning will remove surface contamination
that could lead to rust. Some installations may require
cleaning on a weekly basis.
• Do not clean with steel wool pads.
• Do not use cleaners that are not specifically
intended for stainless steel (this includes glass,
tile and counter cleaners).
• If any surface discolors or rusting appears, clean it
quickly with Bon-Ami or Barkeepers Friend Cleanser
and a non-abrasive cloth. Always clean in the direction
of the grain. Always finish this process with Claire
Stainless Steel Polish and Cleaner or comparable
product to prevent further problems.
• Use of abrasive pads such as Scotchbrite will
cause the graining in the stainless to become
blurred.
• Rust that is allowed to linger can penetrate into the
surface of the stainless steel and complete removal of
the rust may not be possible.
Your U-Line product has been designed for either free-
standing or built-in installation. When built-in, your unit
does not require additional air space for top, sides or rear.
However, the front grille must NOT be obstructed and
clearance is required for electrical connection in the rear.
Note: Unit can NOT be installed behind a closed cabinet
door.
Cut-Out Dimensions
Follow the cut-out drawing in Figure 1. The 24-3/16"
width allows 1/4" for ease in installation and removal of
the unit. 24" is the counter depth in most installations.
The unit is 23-1/4" deep including the handle on Black
and White 2075WC models, 23-1/4" deep including the
wood overlay frame on 2075WCOL models and 23-1/4"
deep including the door and not the handle on Stainless
Steel models (see Figure 2).
3 Prepare Site
1-1/2"
7"
23-1/4"
24-3/16"
Figure 1

02/2005 5www.U-LineService.com
™2075WC/2075WCOL Wine Captain®
Product Dimensions
Please note that the unit has adjustable feet that can add
one additional inch to height during leveling or to match
adjacent cabinets (see Figure 29 on Page 13).
Door Swing/Clearances Information
Black, White and Wood Overlay units have a zero
clearance for the door to open 90° (see Figure 3).
Stainless Steel models require a minimum of 2-1/8" door
clearance to accommodate the handle if the unit is
installed next to a wall or similar type of structure.
Reversing the Door
(Black and White Units Only)
All U-Line units (except
Stainless Steel models) may
be left- or right-hand
opening. The door opening is
easily reversed by moving the
hinge hardware to the
opposite side. The top hinge
hardware will be used on the
bottom of the other side and
the bottom hinge hardware
will be used on the top of the
other side (see Figure 4).
To reverse the door:
1. Remove top hinge screw
pin from door (7/64"
Allen wrench or Phillips
screwdriver, depending on your unit’s construction)
(see Figure 5). Remove door by tilting forward and
lifting off bottom hinge pin.
23-1/4"
Including
Wood Overlay
23-15/16"
Wood Overlay
Black and White
34-1/8"
23-1/4"
Including
Handle
23-15/16"
34-1/8"
Stainless Steel
25-3/8"
Including
Handle
23-15/16"
34-1/8"
Figure 2
90°
Door Swing
Wall Wall
21"
25-1/2"
90°
Door Swing
21"
25-1/2"
Stainless Steel
Black, White and Wood Overlay
2-1/8" Min.
Figure 3
WARMER
17
4
35
26
COLDER
Figure 4

2075WC/2075WCOL Wine Captain®
www.U-LineService.com 602/2005
™
2. Remove plastic screw plugs (3 each, top and bottom)
from new hinge location. Do not discard (see Figure 6 ).
3. Remove top hinge (3 screws), reinstall hinge screw pin,
and remount on opposite side BOTTOM (see
Figure 7 ).
4. Remove the two door closer inserts from the existing
bottom hinge and install as shown on the new bottom
hinge (see
Figure 8 ).
5. Remove existing bottom hinge (3 screws) and remount
on opposite side TOP. Remove hinge screw pin.
6. Remove the plastic hole plug from the top of the door
to allow the pivot pin to be inserted in the new
location. Install the plug into the vacated hole on the
opposite side.
7. With bottom of door facing up, remove pivot plate
(2 screws), flip over, and remount on opposite side of
door (see
Figure 9 ). Be sure angled side of plate faces
center.
8. Holding door upright with top of door tilted forward,
place hole of door pivot plate on bottom hinge screw
pin (see
Figure 10 ).
9. Tilt top of door into
position in top hinge and
install top hinge screw pin.
10. Install plastic screw plugs
removed in Step 2 in old
hinge holes (3 each, top
and bottom).
Other Site Requirements
Power Supply
The unit requires a grounded and polarized 115 VAC,
60 Hz, 15A circuit (normal household current). See
Electrical Specifications on Page 13.
Environmental Requirements
The surrounding air temperature must be at least 50°F
(10°C) but must not exceed 110°F (40°C). The unit must
not be located near heat-generating equipment or in
direct sunlight.
Screw Plugs
Figure 5 Figure 6
Figure 7 Figure 8
Hinge
Screw
Pin
Door
Closer
Inserts
Figure 9
Figure 10

02/2005 7www.U-LineService.com
™2075WC/2075WCOL Wine Captain®
Side-By-Side Installation
Instructions
For a complete refreshment center, install your 2075WC or
2075WCOL unit beside a U-Line Refrigerator, Ice Maker or
Combo Model (see Figure 11 for typical cut-out). Note
that each Side-By-Side Installation will be different.
• Cut-out width for a side-by-side installation is the total
of the widths listed under Cut-Out Dimensions in each
unit’s Installation Guide.
For example:
Placing a 2075 Wine Captain®next to a 2015 series unit
would require a cut-out width of:
24-3/16" + 15-3/16" = 39-3/8"
Placing a 2075 Wine Captain®next to a 2075 series unit
would require a cut-out width of:
24-3/16" + 24-3/16" = 48-3/8"
•
No trim kit is required. However, 1/4-inch space needs to
be maintained
between the units to ensure
unobstructed door swing.
• Units must operate from separate, properly grounded
electrical receptacles placed according to each unit’s
Electrical Specifications.
The U-Line Wine Captain®is equipped with wood-
trimmed wine racks that are coated at the factory with a
clear vinyl sealer, which will adequately protect the wood
in normal usage. A final finish coat was not applied so
that the wood trim could be stained to match décor or
overlay frame. The trim on the racks may be coated with a
final finish or stained.
2075WCOL Models are designed for, and require
installation of, an Overlay Frame.
If none of these treatments are to be included in this
installation, go on to 5 Adjust Door.
CAUTION
To prevent permanent damage to the inner liner of the
Wine Captain®, the wine rack wood trim MUST be
removed from the unit for staining and/or finishing.
Allow stain/finish to dry thoroughly (at least 24 hours per
coat) in accordance with the stain/finish manufacturer’s
instructions prior to re-installing the wood trim inside the
cabinet of the Wine Captain®. Failure to do so may cause
the inner liner of the unit to have a permanent odor,
which is not covered by the warranty.
Adding a Final Finish Coat to Wood
Trim
1. Remove each wine rack by
sliding it out and up. See
Figure 12.
2. Remove and save screws
securing wood trim to the
racks.
3. Lightly scruff sand the
wood trim with 280 grit
3M Tri-M-Ite sandpaper.
4. Remove sanding dust with
a tack cloth.
5. Apply a thin coat of Minwax Polycrylic, following
container label for directions. Allow to dry 24 hours.
6. Lightly sand, tack and reapply 2 times, if desired.
7. Allow the final coat to dry for 24 hours.
8. Reinstall wood trim to wine racks using screws
removed in Step 2.
9. Reinstall wine racks in unit.
10. For 2075WC units, go on to 5 Adjust Door.
1-1/2"
7"
34-1/4"
to
35-1/8"
1/4" Space
Between
Appliances
23-1/4"
Figure 11
Typical Side-By-Side Cut-Out
4 Prepare Racks and Door Frame
Slide Out
and Up
Figure 12

2075WC/2075WCOL Wine Captain®
www.U-LineService.com 802/2005
™
Staining Wood Trim a Different
Color
1. Remove each wine rack by sliding it out and up. See
Figure 12.
2. Remove and save screws securing wood trim to the
racks.
3. Apply Minwax Water-Based Wood Stain to wood with a
synthetic foam brush. Stain must penetrate
approximately 3 minutes. After this period, while stain
is still wet, take a stain-dampened rag and remove all
excess stain. Wipe in the direction of the grain with
medium pressure to achieve the desired stain color.
4. After 2 hours, repeat Step 3.
5. Allow stain to dry for a minimum of 3 hours before
finishing.
6. Sand the wood with very fine sandpaper to smooth the
surface from the staining process.
7. Remove sanding dust with a tack cloth.
8. Apply a thin coat of Minwax Polycrylic, following
container label for directions. Allow to dry 24 hours.
9. Lightly sand, tack and reapply 2 times, if desired.
10. Allow the final coat to dry for 24 hours.
11. Reinstall wood trim to wine racks using screws removed
in Step 2.
12. Reinstall wine racks in unit.
13. For 2075WC units, go on to
5 Adjust Door .
Overlay Frame
(2075WCOL Units Only)
Frame Preparation
An overlay frame covers the door frame to give a built-in
appearance. Appropriate hardware and a copy of these
instructions will be included in the unit.
IMPORTANT
The thickness of the wood overlay frame must be 3/4".
The door frame must not weigh more than 20 lbs.
1. Create an overlay frame to the dimensions shown in
Figure 13.
IMPORTANT
Rear View of wood frame for right-hand hinge shown.
Use mirror image for left-hand hinges.
27-3/4"
30"
21-1/2"
23-3/4"
Rear View
of
Wood Frame
1/8"
13/16"
1/8"
Relief Notch for Pivot Plate
(Right Hand Hinge Shown)
3/4"
Figure 13

02/2005 9www.U-LineService.com
™2075WC/2075WCOL Wine Captain®
2. Typical routing dimensions
are shown in
Figure 14 .
3. Create a relief for pivot plate by cutting notch in top
corner and coinciding back corner of overlay frame.
Refer to
Figure 15 for exact specifications.
Route notch in top corner of overlay frame as shown
(see Top and Side Views). Top of notch is entire depth
of frame, front to back.
Width: 13/16"
Depth: 1/8"
Route notch in backside of top corner of overlay frame
(see Back and Side Views).
Width: 13/16"
Depth: 1/8"
Height: 1-17/32" from top edge of frame (less 1/8" for
depth of notch on top of frame)
Radius of corner notch: 1/8" (see Back View)
4. Drill holes for pivot plate mounts (see Figure 15 , Back
View).
5/16" diameter x 1/2" deep, from the routed surface
CAUTION
Be careful not to drill too deep! Drilling holes too deep
may destroy your door frame.
5. Drill hole for upper door hinge (top of frame) (see
Figure 15 , Top View).
0.177" diameter
(#16 drill) x 11/16" deep
6. Drill hole for lower door hinge (see Figure 15 , Bottom
View).
5/16" diameter x 1/4" deep
CAUTION
It is important to ensure that all drilled holes are drilled to
the correct depth in order to avoid splits in the wood
when hardware is installed.
2-1/4"
1-13/16"
1-1/8"
11/16"
(Ref.)
7/16"
(Ref.)
5/32"
3/4"
3/8"
Figure 14
Top View
Back View
Bottom View
Side View
13/16"
1-17/32"
13/16"
13/32"
3/8"
Door Bottom:
5/16" Dia. x1/4" Deep
Chamfer 1/32" x45°
3/8"
1/8" 1/8"
13/16"
7/16"
1/8"
13/32"
3/4"
13/32" 0.177" Dia. (#16 Drill)
x11/16" Deep
5/16" Dia.
x1/2" Deep
1/32" R
1/8" R
Figure 15

2075WC/2075WCOL Wine Captain®
www.U-LineService.com 10 02/2005
™
Installation Instructions
Preparing Door
Note: Door is not attached. It
is in a separate box inside the
unit box and taped to the
unit.
1. Lay door on a clean, flat
surface with the gasket
facing up.
2. Pull gasket completely out
of the groove. Start in the
middle and pull outward,
moving toward the edge
(see
Figure 16 ). This may take some force.
Note: Lay gasket flat on a clean surface to avoid
disturbing interior magnet.
Checking Overlay Fit
1. Turn door over and lay overlay frame on front side of
door. Make sure frame is fully seated on all four sides.
See Figure 17.
2. Visually check for gap between frame and glass. If there
is an objectionable gap, follow steps under Applying
Foam Tape to Overlay Frame. If there is little or no gap,
continue to Attaching the Overlay Frame.
Applying Foam Tape to Overlay Frame (If required)
1. Cut foam tape into four pieces, two pieces the width
of the overlay frame and two pieces the height of the
overlay frame.
2. Remove the adhesive protection strip from one piece of
the foam tape and align to the edge of the overlay
frame as shown in
Figure 18 , adhering the foam tape
to the overlay frame.
3. Trim each piece of tape immediately after application.
Do not allow any overlapping of the foam tape.
Damage to the overlay frame can occur if the foam tape
is not trimmed properly.
Attaching the Overlay Frame
1. Tap nylon inserts into the top holes drilled in the
overlay frame. Use two #6 screws to attach top pivot
bracket to the overlay frame (see Figure 19).
2. If a user-supplied cabinet handle will be used, attach its
hardware to the overlay frame at this time.
IMPORTANT
User-supplied cabinet handle MUST be counter bored to
make sure mounting hardware is below surface of overlay
frame. Failure to do so can cause damage to overlay
frame and/or door. Overlay frame will not sit flush to door
if mounting hardware is not counter bored.
Door
Gasket
Figure 16
Not Fully Seated Little or No Gap Objectional Gap
Figure 17
Incorrect Correct
Inside Edge
Figure 18
Typical Wood
Frame
Top Pivot
Plate
#6 X 5/8"
Flat Head Screw
Two Required
8 mm Plug Insert
Two Required
Figure 19

02/2005 11 www.U-LineService.com
™2075WC/2075WCOL Wine Captain®
3. Secure the front of the door to the back of the overlay
frame using tape on all four corners, as shown in
Figure 20 . Make sure all four edges are aligned.
4. Place door and overlay frame on a flat, clean protective
surface. Use the door frame holes as a guide to lightly
punch pilot holes for the #6 x 1" pan-head screws. See
Figure 21 .
5. Attach the door to the overlay frame using the #6 x 1"
wood screws.
IMPORTANT
If you decide to drill pilot holes, remove the door and do
not use a drill bit larger than 7/64". Do not drill deeper
than 3/8". Door frame and overlay frame must be aligned
properly or the door will not operate correctly.
Note: The door frame is designed with a slight amount of
“play” to square it to the overlay frame.
6. Remove all traces of tape securing overlay frame to
door frame.
7. Starting at the corners and working toward the center,
push the door gasket back into place. Make sure gasket
is seated on all four sides.
Installing the Door
IMPORTANT
Pivot posts must be clean. Closers must also be clean and
greased to ensure proper operation.
1. Insert pivot post into bottom hinge, making sure to
tighten only until post is level with outside of hinge.
2. Install door closer. See Figure 26 on Page 12. Be sure
that bosses on closers align with holes in hinge.
3. Holding door upright with top of door tilted forward,
place hole of pivot plate onto bottom hinge screw pin.
Be sure that bosses on closers align with holes in pivot
plate.
4. Tilt top of door into position and install top hinge screw
pin. See
Figure 22 . Tighten only until post is level with
top of hinge.
5. Go on to
5 Adjust Door .
Door
Frame
Overlay
Frame
Tape
Figure 20
Rear View
of
Door and
Overlay Frame
Punch Pilot Holes for use
with # 6 x 1" Pan-head
Screws
– 10 Places
Figure 21
Top Pivot Plate
Pivot Post
Figure 22

2075WC/2075WCOL Wine Captain®
www.U-LineService.com 12 02/2005
™
Checking Door Alignment
The unit’s door is aligned at the factory before shipment.
However, its alignment could have been disturbed during
shipment or during overlay frame installation.
IMPORTANT
Properly aligned, the door should be 1/8" below the top of
the unit’s cabinet, NOT flush with the top (see
Figure 23 ).
1. Compare the top edge of the door to the top edge of
the cabinet.
2. If the door edge is 1/8" below and parallel to the top of
the cabinet, go on to
6 Prepare Power Supply . If it is
not, note whether the side opposite the hinge needs to
be moved UP or DOWN, and use the following
procedure.
Adjusting Door Alignment
1. Remove top hinge screw
pin (7/64
" Allen wrench or
Phillips screwdriver,
depending on your unit’s
construction, see
Figure 24). Remove door
by tilting forward and
lifting off bottom hinge
pin.
2. With door upside-down,
loosen but do not remove
the two screws on the door’s bottom hinge plate.
3. See
Figure 25 . If the top far edge of the door needs to
move UP, move the hinge plate toward the outside of
the door and retighten screws. If the top far edge of the
door needs to move DOWN, move the hinge plate
toward the inside of the door and retighten screws.
4. Mount the door to recheck alignment and repeat
Steps 2 and 3 if further adjustment is necessary.
5. When top edge of door is parallel to top edge of
cabinet, remove the door and ensure the two screws
are secure.
6. Remove the door closers from the bottom hinge, clean
thoroughly and lubricate the mating surfaces with
petroleum jelly.
7. Reinstall the closers, lining
up the bosses with holes in
hinge and hinge plate (see
Figure 26 ).
8. Mount the door, install top
hinge pivot pin and go on
to
6 Prepare Power
Supply
.
5 Adjust Door
1/8"
Figure 23
Figure 24
Angled Edge
Towards Center
of Door
Slotted
Mounting
Holes
Raise
Outside
Door Edge
Lower
Outside
Door Edge
Figure 25
Door
Closer
Inserts
Boss
Figure 26

02/2005 13 www.U-LineService.com
™2075WC/2075WCOL Wine Captain®
Electrical Specifications
CAUTION
Electrical installation must observe all state and local
codes. This unit requires connection to a grounded (three-
prong), polarized receptacle that has been placed by a
qualified electrician.
The unit requires a grounded and polarized 115 VAC,
60 Hz, 15A power supply (normal household current).
An individual, properly grounded branch circuit or circuit
breaker is recommended. GFCI (ground fault circuit
interrupter) is usually not required for fixed location
appliances and is not recommended for your unit because
a GFCI could be prone to nuisance tripping. However, be
sure to consult your local codes.
See Figure 27 for recommended receptacle location.
WARNING
SHOCK HAZARD — Electrical Grounding Required.
• Never remove the round grounding prong from
the plug and never use a two-prong grounding
adapter.
• Never use an extension cord to connect power to
the unit.
Go on to 7 Level the Unit.
Leveling Information
Note: It is recommended that the unit is level.
1. Use a level to check the
levelness of the Wine
Captain®from front to
back and from side to
side. Level should be
placed along top edge
and side edge as shown
(see Figure 28).
2. If the Wine Captain® is not level, adjust the feet on the
corners of the unit as necessary (see
Figure 29 ).
3. Check the levelness after each adjustment and repeat
the previous steps until the unit is level. Go on to
8 Install the Unit .
Installation Tip
If the room floor is higher than the floor in the cut-out
opening, adjust the rear feet to achieve a total unit rear
height of 1/8 " less than the opening’s rear height. Shorten
the unit height in the front by adjusting the front feet.
This allows the unit to be gently tipped into the opening.
Readjust the front feet to level the unit after it is correctly
positioned in the opening.
6 Prepare Power Supply
1-1/2"
7"
23-1/4"
Figure 27
7 Level the Unit
Check
Level
Figure 28
Turn Foot to Adjust
Figure 29

2075WC/2075WCOL Wine Captain®
www.U-LineService.com 14 02/2005
™
Anti-Tip Bracket Installation
1. Locate two Anti-Tip Brackets included inside the unit.
2. Place the unit into the area where it will be installed.
Check the door, sides and top for a proper fit. Also test
to make sure the door opens and closes freely.
3. Remove grill and place a mark on the floor at the front
of the unit. Also place a mark on the floor in the center
of the unit. See
Figure 30 .
4. Remove the unit. Using a square, extend a centerline
20-1/4" toward the back wall. See Figure 31 . At the
back of the centerline, mark a line that measures
11-1/16" to the left and right. This line serves as the
back edge for the Anti-Tip Brackets and its furthest
points mark the outer edge of each bracket.
Note: Instructions are shown for built-in installation. Use
same dimensions for free-standing installation.
5. Place the Anti-Tip Brackets on the floor against the line
drawn for the outer edge. Mark spots for the screw
holes. See
Figure 32 .
6. Use a 1/8" drill to make two starter holes and fasten the
Anti-Tip Brackets to the floor using the screws provided.
CAUTION
Other hardware is required for floors made of materials
other than wood.
7. Place the unit back into position, making sure the feet
engage the Anti-Tip Brackets properly. Check the
alignment of the lines made on the floor in Step 3 with
the position of the front feet to ensure proper
positioning.
8 Install the Unit
Marks on Floor
Figure 30
20-1/4"
Back
Wall
Line Marks
Back
of Unit
Front
of Unit
11-1/16" 11-1/16"
Centerline
Marks
on Floor
Figure 31
Back
Wall
Back
of Unit
Drill Holes and
Mount Anti-Tip
Brackets to Floor
Front
of Unit
Figure 32

02/2005 15 www.U-LineService.com
™2075WC/2075WCOL Wine Captain®
Installation Troubleshooting
Problem
Q:
The door remains open unless it is pushed closed.
Solution
A:
The hinges should be self-closing when the door is open
approximately 8
" . If this is not the case, make sure the
closers (at the bottom of the hinge pin) are clean, greased
and installed correctly. Also, re-check leveling from front
to back of the unit and readjust if necessary. Make sure
that pivot plate is installed correctly.
Initial Start-Up
The unit is shipped with the control preset. No adjustments
should be necessary at this time. For information about
Adjusting the Temperature Control, see the User Manual.
Start-Up Troubleshooting
Problem
Q:
Unit does not appear to turn on when plugged in.
Solution
A:
Make sure outlet has power (circuit breaker has not
tripped). Check to see that control is turned on.
Problem
Q:
Light is on with door closed.
Solution
A:
Make sure switch located to the right of the control dial
on the grille is set to OFF.
The Wine Captain®has an interior light that is illuminated
when the door is opened. The light can be activated while
the door is closed by depressing the switch to the ON
position.
IMPORTANT
See the User Manual’s Troubleshooting Guide for more
solutions.
9 Start-Up for the First Time

™
©2005 U-Line Corporation
Publication No. 30054E
02/2005 Rev. A
U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in
undercounter icemakers, Combo®icemaker/refrigerators, Wine Captain®wine storage units,
refrigerators, refrigerated drawers and refrigerator/freezers.
For more than four decades, U-Line has distinguished itself as the leader in built-in
undercounter ice making, refrigeration and wine storage appliances.
Who to Call
Service Information
If the need for service arises, contact the dealer from
whom the unit was purchased. State the Model Number
and Serial Number and explain the problem. The Model
and Serial Number plate is located inside unit at upper
right hand corner.
If you need to locate a service company, you can go online
at www.U-LineService.com and search for a service
company by zip code.