Uberhaus 11S067E User manual

A2
A2
A1
A1
HEX.KEY WRENCH 4MM
SEAT CUSHION
BACK CUSHION
BOLT CAP
WASHER d6.5*D13*1.0
BOLT M6*35BACK ASSEMBLY
SEAT ASSEMBLY
LEFT ARM
RIGHT ARM
BOLT M6*65
BOLT M6*16
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
1
1
1
1
2
4
2
8
8
1
1
1
KFS8091-CS01
KFS809W-CS02
KFS809W-CS03
KFS809W-CS04
17C33A0755001Y4
17C33A0706001Y4
17C33A0712001Y4
17FA05040301-Y4
1800337004
61K809WX00001BA
61K809WY00001BA
17KAA0101----Y4
PARTS LIST
PART
NO.
PART
NO.
MATERIAL CODE MATERIAL CODE
PART PART
Q’TY Q’TY
FIGURE 1
Attention:
Make sure that each bolt needed for all steps match the corresponding
figure to ensure proper assembly.
PAGE 1 OF 2 COURTYARD CREATIONS INC.
Do not discard any of the packaging until you have checked that you have all the parts and pack of fittings.
Keep children away during assembly. This item contains small parts which can be swallowed by children.
Children should always be under direct adult supervision while using the product.
Retain the assembly instructions for future reference.
!
!
!
SOFA SET - SOFA
RONA CODE: 79275019
ITEM NUMBER:11S067E
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
ASSEMBLY INSTRUCTIONS
UBERHAUS
STEP 1:
Place the back assembly (#A1) onto a non-abrasive surface, such as
a carpet. Insert the back assembly (#A1) into the seat assembly (#A2).
See Figure 1.

Cleaning and Maintenance
• Wash frame parts with mild soap and water, rinse thoroughly, and dry frame completely. Do not use bleach, acid,
or other solvents on the frame parts.
• Cushions may be washed on the surface only by using mild soap and water or commercial foaming upholstery
cleaner if necessary. If washed, rinse well and hang to dry. Do not machine wash or dry
•We recommend the use of furniture covers when not in use.
•Please inspect and tighten all bolts or fasteners on a regular basis to ensure proper performance and safety of
your chair.
•In order to prolong the life and beauty of your chair, we recommend that it be stored in a dry and protected area
during off season periods.
STEP 2:
At the rear of the seat, fasten the seat assembly (#A2) to the back
assembly (#A1) by using bolts (#A5) and washers (#A8). Keep the
bolts loose. See Figure 2.
STEP 3:
Fasten both the left arm (#A3) and the right arm (#A4) to the seat
assembly (#A2) by using bolts (#A6) and washers (#A8). Keep the
bolts loose. See Figure 3.
FIGURE 2 FIGURE 3
FIGURE 4 FIGURE 5
#A6 BOLT M6*16
STEP 4:
Fasten both the left arm (#A3) and the right arm (#A4) to the back
assembly (#A1) by using bolts (#A7) and washers (#A8). Make sure
that all of the bolts have been tightened completely and then cover
them with bolt caps (#A9). See Figure 4.
STEP 5:
Place the cushions (#A11 and #A12) on to the chair. Secure the
cushions in place by using the velcro straps provided. See Figure 5.
A5
A7
A3
A4
A1
A8 A9
A8
A8
A6 A6
A8
A9
A9
A9
#A5 BOLT M6*65
65 16
PAGE 2 OF 2
A11
A12
A1
A2
A2
A3
A4
#A7 BOLT M6*35
35