Uberhaus RONA 74805007 User manual

1
GENEVA VANITY
RONA SKU # 74805007
UBERHAUS

PACKAGE CONTENTS
A B
D E
A
Part Description Quantity
B
C
D
E
1
2
Vanity
Shelf
Leg (Left)
Leg (Right)
1
1
2
2
C
Backsplash

HARDWARE CONTENTS
Part Description Quantity Picture
AA
WARNINGS AND CAUTIONS
WARNINGS
Two people are recommended for assembly.
CAUTION
Do not overtighten the bolts.
ø 5/16" x 1 3/4" L
Hex. Head Bolt
ID 5/16"
Spring Washer
ID 5/16" x OD 3/4"
Flat Washer
ID 1/4"
Spring Washer
8
8
8
4
ID 1/4" x OD 5/8"
Flat Washer 4
!
3
BB
CC
DD
EE
FF
GG
1/4" x 5/8" L
Pan Head Bolt 4
Mounting Plate 3
HH 1/4" x 1/3" L
Pan Head Bolt 6

PREPARATION
ASSEMBLY INSTRUCTIONS
Step 2 Place Vanity (A) by facing down on a soft and clean
surface.
Step 1
Step 1 Remove knob and bolt on inside of drawer front, install knob to outside of drawer
front with the same bolt, using a Phillips head screwdriver.
A
Before installing product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to
install the product.
Please contact the store where the product was purchased.
Estimated assembly time: 20 minutes.
Tools required for assembly (not lncluded): Phillips head screwdriver & 1/2" Wrench.
4

Attach Shelf (C) to Legs (D)
& (E) using Pan Head Bolt
(DD), Spring Washer (EE)
and Flat Washer (FF),
tighten with Phillips head
screwdriver.
Step 4
D
D
C
E
DD
FF EE
5
Step 3
Hardware Used In Step 3
AA CC
BB
CC ID 5/16" x OD 3/4"
Flat Washer
BB
AA
ID 5/16"
Spring Washer
ø 5/16" x 1 3/4" L
Hex. Head Bolt
x 8
x 8
x 8
Attach Leg (D) & (E) to corner block of Vanity (A) using Hex. Head Bolt (AA),
Spring Washer (BB) and Flat Washer (CC), tighten with Phillips head
screwdriver.
A
E
D
D
E
or
For bottom leg bolt,
tighten with
screwdriver or
wrench as an option.
CC
BB
AA
Step 2 & 3
Step 4
Step 1
Before installing product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to
install the product.
Please contact the store where the product was purchased.

Hardware Used In Step 5
6
DD
FF
Hardware Used In Step 4
ID 1/4" x OD 5/8"
Flat Washer
FF
ID 1/4"
Spring Washer
EE x 4
x 4
x 4
1/4" x 5/8" L
Pan Head Bolt
Turn the Vanity upright.
Attach Mounting Plate
(GG) to Backsplash (B)
and back of Vanity (A)
using Pan Head Bolt (HH),
tighten with Phillips head
screwdriver.
Step 5
DD
x 6
1/4" x 1/3" L
Pan Head Bolt
HH
GG x 3
Mounting Plate
HH
EE
GG
If leveling is needed, adjust
by turning the levelers on
bottom of legs, to desired
position.
Step 6
OUT
AB
or
Step 2 & 3
Step 4
Step 5 & 6
Step 1

7
HH
GG
Step 2 & 3
Step 4
Step 5 & 6
Clean up excess water and spills immediately. Use a blotting rather than a wiping
action. Water left over a long period of time will cause white spots in the finish.
Alcohol, perfume, after-shave and some medications may damage the finish.
Avoid extreme changes in temperature by arranging furniture away from radiators,
heating and air vents or air conditioning units.
Avoid placing your furniture in direct sunlight, as sunlight causes fading.
CARE AND MAINTENANCE
Dusting your vanity frequently with a soft, dry, lint-free cloth is recommended.
Polishing at least every six months is encouraged. Polishes that contain mild
detergents, emulsifiers and mineral oil are recommended. Avoid using silicone
cleaners and waxes. When polishing, clean the surface by rubbing in the direction
of the grain.
Step 1

Step 2 & 3
Step 4
Step 5 & 6
Pop-up Drainpipe 1-1
Rubber Gasket
Rubber Gasket
Nut
Nut
Rubber Gasket
"U" Drainpipe
Rubber Gasket
Nut
"L" Drainpipe
POP-UP ASSEMBLY INSTRUCTIONS
Press once on Pop-up to keep water in the sink.
Press again on Pop-up to let water out of sink.
8
RONA SKU#: 74805007 VANITY
Vanity Top
With Sink
Sink With
Drain Hole
Vanity Top
With Sink
Sink With
Drain Hole
Vanity Top
With Sink
1
2
1 1
3
4
1
5
6
7
8
9
10
Sink With
Drain Hole
Vanity Top
With Sink
1
5
7
9
10
Sink With
Drain Hole
UBERHAUS
1
2
3
4
5
6
7
8
9
10