Ubiquiti AF-11G35 User manual

https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

Antenna Compatibility
The airFiber AF-11G35 antenna is designed for use with the
DLU)LEHU;©UDGLR©PRGHO©$)õ);*.
Installation Requirements
• 13 mm wrench (pre-assembly tool)
• 17 mm wrench (pole-mounting tool)
• DLU)LEHU©$)õ);©UDGLR©VROG©VHSDUDWHO\©ZLWK©GXSOH[HUV©
installed
• Clear line of sight between airFiber radios
• Vertical mounting orientation
• Mounting point:
• At least 1 m below the highest point on the structure
• For tower installations, at least 3 m below the top of
WKHWRZHU
• Ground wires – min. 10 AWG (5 mm2©DQG©PD[©OHQJWKP©
$VD©VDIHW\©SUHFDXWLRQ©JURXQG©WKH©DLU)LEHU©UDGLRV©WR©
grounded masts, poles, towers, or grounding bars.
WARNING: Failure to properly ground your
airFiber radio will void your warranty.
• (Recommended) 2 Outdoor Gigabit PoE surge protectors
Note: For guidelines about grounding and lightning
protection, follow your local electrical regulatory codes.
• (Optional) If not using PoE: DC power source and 12/30 AWG
power cable.
• Outdoor, shielded Category 6 (or above) cabling and
shielded RJ-45 connectors are required for all wired Ethernet
connections.
* Check your local/regional regulations for the allowable antenna gain
allowed for your application.
https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

Specifications
airFiber AF-11G35
Dimensions ©[©©[©©PP©©[©©[©
Weight 16.5 kg (36.38 lb)
Frequency 10.3 to 11.7 GHz
Gain 35 dBi
HPOL Beamwidth 2.5°
VPOL Beamwidth 2.5°
0D[LPXP©96:5 2:1
Wind Survivability 200 km/h (125 mph)
Wind Loading 1538 N @ 200 km/h
Polarization
Default
After Rotating OMT
H/V
±45°
Cross-Pol Isolation 35 dB
Mounting Uses the AF-5 Mounting System
Pattern Regulatory ETSI 302 217-4-2, Class 3
and FCC Cat B
https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35

Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: Do not use this product in location that can
be submerged by water.
WARNING: Avoid using this product during an electrical
storm. There may be a remote risk of electric shock from
lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a
different power source than those specified may result in improper
operation, damage to the equipment or pose a fire hazard if the
limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service
should be provided only by a qualified service technician.
https://arttel.ru/
https://arttel.ru/shop/antenny/ubiquiti-airfiber-11g-35