Ubiquiti W-DSL-2G16 User manual

Installation Guide
AirMax 11X14" Grid Antenna
Welcome
Thank you for your purchase of this Ubiquiti Grid Antenna.
These instructions are for the following models:
(I) W-DSL-2G16
(II) W-DSL-5G23
Tools Required for Mounting
10mm wrench (Qty. 1)
Support
Internet: www.ubnt.com
Internet Support Forum: www.forum.ubnt.com
Ubiquiti support engineers are located in the U.S. and in Europe and are
dedicated to helping customers resolve software, hardware compatibility,
or eld issues as quickly as possible.
A
D
CB
F G H I J K
B
C
D
E
F
G
H
M6 U-Bolt
M6 Serrated Flange Nut
M6X20 Bolt
M6 Washer
1
4
2
1
I
J
K
M6 Spring Lock Washer
Feed Support Bushing
4
4
E
A
Contents Qty.
Grid Reector 11X14" Pole Bracket Clamp 1
1
1
1
1
L Bracket
Antenna Feed
Feed Support
General Warranty:
UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) represents and warrants that the Products furnished hereunder shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS
under normal use and operation. UBIQUITI NETWORKS sole and exclusive obligation under the foregoing warranty shall be to repair or replace, at its option, any defective Product that fails during the warranty period. The expense of removal and
reinstallation of any item is not included in this warranty.
and performance of the Products. UBIQUITI NETWORKS reserves the right to inspect all defective Products (which must be returned by Buyer to UBIQUITI NETWORKS factory freight prepaid).
No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS. Products returned without an RMA number will not be processed and will be returned to Buyer freight
collect. UBIQUITI NETWORKS shall have no obligation to make repairs or replacement necessitated by catastrophe, fault, negligence, misuse, abuse, or accident by Buyer, Buyer’s customers or any other parties. The warranty period of any repaired or
replaced. Product shall not extend beyond its original term.
Warranty Conditions
The foregoing warranty shall apply only if:
(I) The Product has not been subjected to misuse, neglect or unusual physical, electrical or electromagnetic stress, or some other type of accident.
authorized representatives or otherwise approved by UBIQUITI NETWORKS.
(III) The Product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation.
Disclaimer. UBIQUITI NETWORKS does not warrant that the operation of the products is error-free or that operation will be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible for damages or claims of any nature or description relating to
system performance, including coverage, buyer’s selection of products for buyer’s application and/or failure of products to meet government or regulatory requirements.
Returns
In the unlikely event a defect occurs in this product, please work through the dealer or distributor from which this product was purchased.
(II)
* Products may be different from pictures and are subject to change without prior notice

1
1. Install Feed Support and L Bracket to Grid Reflector
Install Feed Support and L Bracket to Grid Reector by
M6X20 Bolt (Qty. 4)
M6 Spring Lock Washer (Qty. 4)
M6 Washer (Qty. 4)
Vertical Polarization Horizontal Polarization
Vertical Polarization Horizontal Polarization
2. Connect Network Cable to Antenna Feed
Route network cable through the bottom hole of the Feed Support and
attach to the RJ-45 slot on the back of the Antenna Feed.
2
3
3. Install Antenna Feed
Insert Antenna Feed into Feed Support.
Polarization of the W-DSL antenna must match the device that it will be
communicating with (Horizontal to Horizontal, Vertical to Vertical). For
Vertical polarization, the Grid Reector and Antenna Feed must
match gure 3A. For Horizontal polarization the Grid Reector and
Antenna Feed must match gure 3B.
A B
4
4. Install Feed Support Bushing to Feed Support
Wrap network cable with the Feed Support Bushing and then slide it
into the hole in the Feed Support .
5
5. Attach Antenna to Pole
Mounting bracket can accommodate 1.25"-2.2" pole.
Attach antenna assembly to pole by
M6 U-Bolt (Qty. 1)
Pole Bracket Clamp (Qty. 1)
M6 Serrated Flange Nut (Qty. 2)
G J
A
C
C
C
B
B
C
C
FEH
H
E
F
B
B
A
A
C
B
K
C
K
D
I
G
J
AC D
I
B