Ubiquiti Nano G User manual

High-Performance GPON CPE
Model: UF-Nano

Introduction
Thank you for purchasing the Ubiquiti Networks® Nano™G
High-Performance GPON CPE. This Quick Start Guide is
designed to guide you through the installation and also
includes the warranty terms.
Package Contents
NanoG Wall Mount Bracket
Screws
(Qty. 4)
Screw Anchors
(Qty. 4)
High-Performance GPON CPE
Model: UF-Nano
Gigabit PoE (24V, 0.3A)
with Mount Bracket
Power Cord Quick Start
Guide
TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the customer’s
responsibility to follow local country regulations, including operation within legal frequency
channels, output power, and indoor cabling requirements.

System Requirements
• Linux, MacOSX, or Microsoft Windows 7/8/10
• Web Browser: Google Chrome (Other browsers may have
limited functionality)
Hardware Overview
Ports
Port Description
PON SC/APC GPON port supports WAN connections of
2.488 Gbps downstream and 1.244 Gbps upstream.
RJ45 Ethernet port supports 10/100/1000 Mbps
connections and passive PoE to power the device.
RESET Press and release the Reset button to restore the
device to factory default settings.

LED Display
GPON Ethernet
Digital
Display
Power
LED State Status
Green
GPON connected and device is
integrated into a network and
working properly
Red No GPON connection. Error code is
shown on the Digital Display.
Flashing Red Device is discovered by OLT and
waiting to be integrated
Off No power, device is off
White Power on, device is on
Off No Ethernet connection
Green Ethernet is connected
Flashing Ethernet activity

Digital Display
The Digital Display shows device status and RX/TX details
of the PON connection. The Digital Display is also a physical
button. Press the display to cycle through the information.
• Mbps Displays the active download (RX) and upload (TX)
speeds of the PON connection.
RX
TX
• dBm Displays the RX and TX power of the PON connection.
RX
TX
Note: If the GPON LED lights red, a malfunction or
error with the PON connection exists. Check and test
the fiber optic cable to ensure proper operation.

• GB Displays the total aggregate data sent downstream and
upstream through the PON connection. The counter can be
reset using the UFiber Configuration Interface.
RX
TX
• IP Displays the PON (LAN) IP address.
• Time Only shown when the time is synced correctly from
the servers. Enable or disable the time display using the
UFiber Configuration Interface.
*640-00254-04*
640-00254-04

Hardware Installation
The NanoG can be mounted on a wall or placed on a desktop.
WARNING: To reduce the risk of fire or electric shock, do
not expose the NanoG to rain or moisture.
Wall Mounting
1. Use the Wall Mount Bracket as a template and drill four
6mm holes as shown below.
40 mm
40 mm
2. Insert a Screw Anchor into each hole, and then fasten the
Wall Mount Bracket using four Screws.

3. Mount the NanoG by inserting the top of the NanoG into
the Mount Bracket and then pivot the bottom into the
bracket until it locks into place.

Connecting Fiber
Connect the fiber optic cable from the Passive Optical Network
to the PON port.

Connecting Power
1. Connect an Ethernet cable to the LAN port.
2. Connect the power using one of the following options:
• Using the included Gigabit PoE Adapter: Go to
“Connecting to the PoE Adapter”.
• Using a separate PoE switch: Connect the Ethernet
cable from the Nano G to a PoE-enabled Ethernet port
on the switch.
WARNING: The PoE switch must comply with the
power specifications listed in the Specifications
section of this Quick Start Guide.

Connecting to the PoE Adapter
1. Connect the Ethernet cable from the Nano G to the PoE
port on the Gigabit PoE Adapter.
2. Connect an Ethernet cable from your LAN to the LAN port
on the Gigabit PoE Adapter.
3. Connect the Power Cord to the Gigabit PoE Adapter, and
plug the Power Cord into a power outlet.

Mounting the Gigabit PoE Adapter (Optional)
1. Remove the PoE Mounting Bracket from the adapter, place
the bracket at the desired location, and mark the two holes.
2. Pre-drill the holes if necessary, and secure the bracket
using two fasteners (not included).
3. Align the slots on the adapter with the tabs of the PoE
Mounting Bracket, and then slide the adapter down.

Accessing the Configuration Interface
1. Ensure that your computer (or other host system) is
connected to the NanoG.
2. Configure the Ethernet adapter on your host system with a
static IP address on the 192.168.1.x subnet.
3. Launch your web browser. Type https://192.168.1.1 in the
address field. Press enter (PC) or return (Mac).
4. The login screen will appear. Enter ubnt in the Username
and Password fields. Click Login.
The UFiber Configuration Interface will appear. Customize
settings as needed. For more information, refer to the UFiber
documentation, which is available at:
documentation.ubnt.com/ufiber

OLT Compatibility Profiles
The Nano G is compatible with most major brands of OLT
(Optical Line Terminals) and compatibilty may be selected
by using one of three compatiblity profiles. By default, the
NanoG is set to Profile1 - Ubiquiti Networks UFiber OLT. For
other brands, manually select Profile 2 or 3:
1. Disconnect the power to the Nano G.
2. Press and hold the Digital Display button and reconnect
the power.
3. Continue holding the button for about 35 seconds. Release
the button once dashes are displayed.
4. Press the button to select the compatibility mode:
• Pr 1 - Profile 1 (Ubiquiti Networks U Fiber OLT)
• Pr 2 - Profile 2
• Pr 3 - Profile 3
5. Double-click the Digital Display button to select the profile.
Dashes will reappear to confirm your selection.
6. The Nano G will automatically restart with the new profile.

Specifications
UF-Nano
Dimensions 77 x 77 x 28 mm
(3.03 x 3.03 x 1.1")
Weight 110 g (3.88 oz)
Networking Interfaces (1) SC/APC, GPON WAN
(1) RJ45, Ethernet LAN
Networking Interface Speeds (1) GPON WAN, ITU G.984,
2.488 Gbps Downstream,
1.244 Gbps Upstream
(1) GbE LAN, 10/100/1000 Mbps
Management Interface In-Band Ethernet/PON
Normal Optical Power Range TX (Class B+): 1.5 to 5 dBm
RX: -8 to -28 dBm
Power Method 24V Passive PoE (Pins +4, 5; -7, 8)
Dying Gasp Support
Power Supply PoE Adapter: 24V, 0.3A
Max. Power Consumption 7W
Supported Voltage Range 20 to 28V
Processor Specs MIPS-32, 240 MHz
Memory Information 128 MB DDR3
Buttons (1) Display Information
(1) Reset
Operating Temperature -10 to 45° C (14 to 113° F)
Operating Humidity 5 to 95% Noncondensing
Certications CE, FCC, IC

Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: Do not use this product in location that can
be submerged by water.
WARNING: Avoid using this product during an electrical
storm. There may be a remote risk of electric shock from
lightning.
WARNING: CLASS 1 LASER PRODUCT - Do not look into
the ends of the fiber optic cable or SFP modules while
converters are powered.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a
different power source than those specified may result in improper
operation, damage to the equipment or pose a fire hazard if the
limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service
should be provided only by a qualified service technician.
3. This equipment is provided with a detachable power cord which has
an integral safety ground wire intended for connection to a grounded
safety outlet.
a. Do not substitute the power cord with one that is not the provided
approved type. Never use an adapter plug to connect to a 2-wire
outlet as this will defeat the continuity of the grounding wire.
b. The equipment requires the use of the ground wire as a part of the
safety certification, modification or misuse can provide a shock
hazard that can result in serious injury or death.
c. Contact a qualified electrician or the manufacturer if there
are questions about the installation prior to connecting the
equipment.
d. Protective earthing is provided by Listed AC adapter. Building
installation shall provide appropriate short-circuit backup
protection.
e. Protective bonding must be installed in accordance with local
national wiring rules and regulations.

Limited Warranty
UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the
product(s) furnished hereunder (the “Product(s)”) shall be free from defects
in material and workmanship for a period of one (1) year from the date
of shipment by UBIQUITI NETWORKS under normal use and operation.
UBIQUITI NETWORKS’ sole and exclusive obligation and liability under
the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,
to repair or replace any Product that fails to conform to the above
warranty during the above warranty period. The expense of removal and
reinstallation of any Product is not included in this warranty. The warranty
period of any repaired or replaced Product shall not extend beyond its
original term.
Warranty Conditions
The above warranty does not apply if the Product:
(I) has been modified and/or altered, or an addition made thereto,
except by Ubiquiti Networks, or Ubiquiti Networks’ authorized
representatives, or as approved by Ubiquiti Networks in writing;
(II) has been painted, rebranded or physically modified in any way;
(III) has been damaged due to errors or defects in cabling;
(IV) has been subjected to misuse, abuse, negligence, abnormal physical,
electromagnetic or electrical stress, including lightning strikes, or
accident;
(V) has been damaged or impaired as a result of using third party
firmware;
(VI) has no original Ubiquiti MAC label, or is missing any other original
Ubiquiti label(s); or
(VII) has not been received by Ubiquiti within 30 days of issuance of
the RMA.
In addition, the above warranty shall apply only if: the product has been
properly installed and used at all times in accordance, and in all material
respects, with the applicable Product documentation; all Ethernet cabling
runs use CAT5 (or above), and for outdoor installations, shielded Ethernet
cabling is used, and for indoor installations, indoor cabling requirements
are followed.
Returns
No Products will be accepted for replacement or repair without obtaining
a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS
during the warranty period, and the Products being received at UBIQUITI
NETWORKS’ facility freight prepaid in accordance with the RMA process of
UBIQUITI NETWORKS. Products returned without an RMA number will not
be processed and will be returned freight collect or subject to disposal.
Information on the RMA process and obtaining an RMA number can be
found at: www.ubnt.com/support/warranty.

Disclaimer
EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI
NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,
SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM
AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,
EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,
REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,
ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,
SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS
FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY
WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR
TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.
BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR
ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE
TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING
THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE
SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS
AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS
FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD
PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,
DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT
CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY
OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant
that the operation of the Products will be error-free or that operation will
be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible
for damages or claims of any nature or description relating to system
performance, including coverage, buyer’s selection of products (including
the Products) for buyer’s application and/or failure of products (including
the Products) to meet government or regulatory requirements.
Limitation of Liability
EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL
UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR
DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES
(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING
OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE
PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER
LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.

Note
Some countries, states and provinces do not allow exclusions of implied
warranties or conditions, so the above exclusion may not apply to you.
You may have other rights that vary from country to country, state to
state, or province to province. Some countries, states and provinces do not
allow the exclusion or limitation of liability for incidental or consequential
damages, so the above limitation may not apply to you. EXCEPT TO
THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO
NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE
MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY
SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations
Convention on Contracts for the International Sale of Goods shall not apply
to any transactions regarding the sale of the Products.
Compliance
FCC
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operations of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to
correct the interference at his own expense.

Industry Canada
CAN ICES-3(A)/NMB-3(A)
This Class A digital apparatus complies with Canadian CAN ICES-3(A).
CAN ICES-3(A)/NMB-3(A)
Cet appareil numérique de la classe A est conforme à la norme NMB-3(A)
Canada.
Australia and New Zealand
Warning: This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may
be required to take adequate measures.
CE Marking
CE marking on this product represents the product is in compliance with all
directives that are applicable to it.