Ubiquiti UF-AE User manual

UFiber ActiveEthernet Wall Mount Bracket Screws (Qty. 4)
Screw Anchors (Qty. 4)
Package Contents
Installation Requirement
The UF-AE requires an active fiber SFP module and does not support passive GPON SFP
modules.
Hardware Overview
Ports
UF-AE Quick Start Guide

SFP Port
Ethernet Port
Ethernet LED
The hot-swappable SFP port supports a 1 Gbps connection. (You can use an SFP+
module; however, the maximum speed is 1 Gbps.)
The RJ45 Ethernet port supports a 10/100/1000 connection. To power the device, the
port also supports 802.3af active PoE or 24V passive PoE.
Off Ethernet connection down
Amber 10/100 Mbps Ethernet connection up
Flashing indicates activity
White 1000 Mbps (1 Gbps) Ethernet connection up
Flashing indicates activity
UF-AE Quick Start Guide

Signal LED
Power LED
Off Optical signal present
Amber
Loss of optical signal
Check the fiber cable for damage and ensure that it is
properly connected on both ends.
Off Power off
White Power on
Hardware Installation
Wall Mounting
1.
2.
UF-AE Quick Start Guide

3.
UF-AE Quick Start Guide

4.
UF-AE Quick Start Guide

5.
UF-AE Quick Start Guide

Connecting Fiber
The UF-AE requires an active fiber SFP module and does not support passive GPON SFP
modules.
Note: You can use an SFP+ module; however, the maximum speed is 1 Gbps.
1.
UF-AE Quick Start Guide

2.
3.
Connecting LAN
UF-AE Quick Start Guide

Connecting Power
OR
Note: The airCube AC provides a 1 Gbps Ethernet connection and Wi-Fi
connectivity with PoE passthrough, so it is the ideal complement to the device for
CPE installations.
UF-AE Quick Start Guide

OR
WARNING: The switch port must comply with the power specifications listed in
this Quick Start Guide.
Specifications
UF-AE
Dimensions 76.5 x 76.5 x 26.4 mm
(3.01 x 3.01 x 1.04")
Weight 68 g (2.40 oz)
UF-AE Quick Start Guide

UF-AE
Networking Interfaces (1) 1 Gbps SFP Port
(1) 10/100/1000 Mbps RJ45 Port
Power Method 802.3af PoE: (Pins 1, 2+; 3, 6-)
24V Passive PoE: (Pins 4, 5+; 7, 8-)
Power Supply 802.3af PoE or 24V Passive PoE Device*
Max. Power Consumption 1.5W
Supported Voltage Range 16 to 57V
LEDs (1) Ethernet
(1) Optical Signal
(1) Power
Operating Temperature -40 to 60° C (-40 to 140° F)
Operating Humidity 10 to 90% Noncondensing
ESD/EMP Protection ± 12kV Contact/Air
Certifications CE, FCC, IC
* Power supply not included.
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture.
WARNING: Do not use this product in location that can be submerged by water.
WARNING: Avoid using this product during an electrical storm. There may be a remote risk of
electric shock from lightning.
WARNING: CLASS 1 LASER PRODUCT - Do not look into the ends of the fiber optic cable or
SFP modules while converters are powered.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current requirements indicated on
the manufacturer’s label. Connection to a different power source than those specified may result in
UF-AE Quick Start Guide

improper operation, damage to the equipment or pose a fire hazard if the limitations are not
followed.
2. There are no operator serviceable parts inside this equipment. Service should be provided only by a
qualified service technician.
Limited Warranty
ui.com/support/warranty
The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and,
where applicable, specify arbitration instead of jury trials or class actions.
Compliance
FCC
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operations of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
ISED Canada
CAN ICES-3(A)/NMB-3(A)
Australia and New Zealand
Warning: This equipment is compliant with Class A of CISPR 32. In a residential environment
this equipment may cause radio interference.
CE Marking
CE marking on this product represents the product is in compliance with all directives that are
applicable to it.
UF-AE Quick Start Guide

WEEE Compliance Statement
Declaration of Conformity
Online Resources
© 2020 Ubiquiti Inc. All rights reserved.
UF-AE Quick Start Guide