Ubixon UBHS-NC1 User manual

UBHS-NC1 User Manual
Table of Contents
Caution
Package Content
Features
Wearing the Headset
Charging the Headset
Storing the Headset
Pairing
Using the Headset to Make Calls
Using the Headset to Listen to Music
3D Sound
Meanings of LED Lights
Troubleshooting
Headset Specification
Caution
1. Do not put the headset near a fire. There is danger of explosion.
2. Do not drop or apply excessive force to the headset. It might cause damage.
3. In case of malfunction, do not try to repair yourself. Please contact nearest
service center immediately.
4. If the headset gets wet, avoid any heat or electrical current, and contact our
A/S center or the place of purchase immediately.
5. Keep out of children’s reach.
6. Do not use chemical products (ex: Bleach) to clean the product.
7. Do not use any unauthorized charging device.
8. When storing the product for an extended period of time, store in a dry place
and avoid extreme temperatures.
9. In order to avoid any danger caused by radio interference, do not use the
headset where its use is forbidden.
10. If you use any medical device (pacemaker, hearing aids etc…), please consult
the manufacturer of your device to make sure that the correct functioning of
your medical device is not affected by RF energy emitted by the Bluetooth
Headset. Your doctor may be able to assist you in obtaining this information.
Headquarter Customer Service Center
Ubixon Co., Ltd.
1344-29 Jungdong B/D 2F,
Seocho-dong Seocho-gu Seoul, Korea
TEL: [phone]
FAX: [phone]
e-mail: [email protected]
http://www.ubixon.net
11. Our product satisfies Bluetooth Core Specification Version 2.0. Some Bluetooth
devices may not be compatible with your headset. For further information about
compatibility, please contact the concerned manufacturer, or our customer
service center.
Company’s Indemnification
Manufacturers, Retailers, Agencies are not responsible for any bodily harm, intentional
damages and damages caused by lack of care.
This User’s Manual was written based on present product specification.
All specification may be modified without prior notification.
Package Content
Headset USB Cable (for recharging) Manual
Features
(1) Left Earphone : Outputs left side sound.
(2) Right Earphone : Outputs right side sound.
(3) Receivers : Outputs the sound.
(4) Microphone : Intakes the sound.

(5) 2 Colors LED : Indicates headset’s status.
(6) Power Switch : Use to turn the device on/off.
(7) USB Port : Allows connecting provided USB cable for recharging.
(8) Backward/End Call : While listening to music, pull the button as indicated to play
the past track. Press and hold the button to rewind
While talking on the phone, pull the button as indicated to end
a call.
(9) Forward : While listening to music, push the button as indicated to play
the next track. Press and hold the button to forward.
(10) Play/Pause : While listening to music, press down the button to
Play/Pause. Press and hold the button to terminate playback.
(11) Volume Down : While talking/listening to music, pull the button as indicated
to lower volume.
(12) Volume Up : While talking/listening to music, push the button as indicated
to increase volume.
(13) Talk/3D Sound : Press down the button to start a call, or to choose a 3D
sound effect.
Wearing the Headset
You can experience innovative portability thanks to Ubixon’s patent technology.
When carrying the headset when talking/listening to music
Charging the Headset
This product uses a rechargeable Li-Polymer battery.
Please fully recharge the battery before first use.
Charging Method:
1. Turn off the headset.
2. Use the provided USB Cable to recharge the headset.
※ The average charging time is 2 hours.
3. Red LED light flashes when charging and blue light flashes when charging is
complete.
4. Disconnect the headset from the USB cable once the charging is complete.
5. When the battery level is low, red LED light will flash rapidly, accompanied by a
warning sound
※Continuous Talk/Music/Standby time: 6Hours/5Hours/80Hours
(This data was measured based on manufacturer’s standard. Actual use time may
vary depending on the condition of use)
Caution:
1. Do not use unauthorized charging device.
2. Disconnect the headset from the USB cable once the charging is complete.
3. Battery must be stored between 0℃ ~ 40℃.
4. You may not use the headset while it is charging.
5. The battery included in the headset is an expandable product. Therefore, the
life time of the battery will diminish in time.
Storing the Headset
1. Please turn off your headset and store in a safe place.
2. Please avoid extreme low/high temperatures and direct sun light when storing
the headset. It could diminish the battery life and cause damage to your headset.
3. Please store your headset and other in-box items in a dry place, far from any
watery devices.
Pairing
You MUST pair the headset with any new Bluetooth device before the first use.
This step creates a unique link between two Bluetooth devices which allows the use

- Additional Page -
G
Caution
Modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
FCC Compliance Information
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received.
Including interference that may cause undesired operation.
Information to User
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ tv technician for help.
G

of the headset without repeating the pairing process for the future use.
The pairing process may vary depending on the Bluetooth devices. Please consult
the device’s user guide for further instruction.
Pairing Method:
1. Turn off the headset.
2. Turn on the headset WHILE holding the ‘Talk’ button.
3. While the blue LED light flashes rapidly, release the ‘Talk’ button.
-> The standby sound emitted once every 5 seconds indicates that the headset
is now in Pairing Mode.
※ The pairing must be completed within 60 seconds. After that, the pairing
mode will be terminated and you must repeat from step 1.
4. Use the phone/MP3 player to search for Bluetooth devices. (Please consult your
phone/MP3 player’s user manual.)
5. Select “Lubix Stereo Headset” among the discovered Bluetooth devices.
6. When prompted for password, enter 0000.
7. You’ll receive ‘Pairing successful’ message indicating that pairing has been
successful.
※ If you receive ‘Pairing unsuccessful’ message, try again from step 1.
Using the Headset to Make Calls
Make Call
1. Make a new call:
enter the desired phone number on your phone, and press
‘Talk’ button on your headset to start a new call.
2. Redial last number: When the ‘Talk’ button is pressed, the last dialed number
will appear on your phone. Pressing the ‘Talk’ button again will connect you to
that number.
3. Voice dial: Pressing and holding the ‘Talk’ button will launch the voice dialing
service.
※ In order to use the voice dialing service, your phone must support
HandsFree profile. Please consult your phone manual for further information.
Answer Call
1. When you receive a call, you will hear a ring tone on your headset, with the LED
light flashing in different colors.
2. Press any button on your headset to answer the call.
End Call
Pull the ‘End Talk’ button to end the call.
If the person you are talking to hang up first, the call will be automatically
terminated.
Refuse Call
When receiving a call, push the ‘End Talk’ button to refuse the call.
※ In order to use this function, your phone must support the ‘Hands free’ profile.
Transfer Call
1. To transfer a call from the phone to the headset, press the ‘Talk’ key
2. Pressing the ‘Talk’ button again will transfer the call from the headset to the
phone.
Volume Level
While talking or listening to music, use ‘+’ / ‘-’ buttons to adjust the volume level.
Using the Headset to Listen to Music
Play/Pause
1. Check to make sure that your headset and your Bluetooth device are paired. If
not, you must pair the devices first. (See our pairing section). If the devices are
paired, and the headset was the last device connected to your phone (or MP3
player), then pressing any button on the headset will connect your headset to
the counter Bluetooth device.
2. Launch the music player on your Bluetooth device.
3. Press ‘▶’ button on the headset to start listening to music.
4. Use ‘▌▌’ button to pause and ‘▶’ button to resume play.
Volume Level
While talking or listening to music, use ‘+’ / ‘-’ buttons to adjust the volume level.
Song Selection
Use ‘|◀◀’ / ‘▶▶|’ buttons to backward/forward songs.
Answering Call While Listening to Music
1. When you receive a call, music will stop and you will hear a ring tone on your
headset.
2. Press any button to answer the call.
3. When the call ends, music will resume playing.
4. Pressing the ‘End Talk’ button will reject the call, and the music playback will

resume.
※ In order to use this function, your phone must support the ‘Hands free’ profile.
3D Sound
Thanks to our 3D sound technology, you can now enjoy exciting sounds. The
following will explain the 4 types of 3D sound that this product supports.
Selecting 3D Sound effect
While in Play/Pause mode, press ‘Talk’ button to choose the 3D sound effect of
your choice.
Types of 3D Sound Effect
3D Sound Effects are programmed in the following order. Each time the ‘Talk’ button
is pressed, the next effect will be in use.
1) Normal: No 3D Sound Effect is applied.
2) XOME: Sound moves out from head and ears. Feels like using speakers while
using earphones (comfortable listening.)
3) LIVE: Reverberation, live sound as in a concert hall.
4) WIDE: Natural and soft reverberation effect with early reflections.
5) MEX: 3D Spatialization and Bass Boost.
Meanings of LED Lights
Headset Status LED Status
Recharging Red LED light is on
Low Battery Red LED Light flashes continuously
Recharging complete Blue LED light is on
Pairing mode Blue LED light flashes once every second
Available for connection Blue LED light flashes once every 4 seconds
Connection complete Blue LED light flashes once every 2 seconds
Talking on the phone Blue LED light flashes once every 2 seconds (long)
Playing Music Blue LED light flashes once every second (long)
Troubleshooting
I cannot turn
my headset on.
This headset is designed to automatically go off when the
battery level is low. Please recharge your headset before
using.
I don’t get as much
talk time as I used to.
The battery included in the headset is an expandable product.
Therefore, the operating time of the battery will diminish in
time.
※ Battery life will defer depending on the condition of use.
I cannot pair my
headset to other
devices
In order to pair your headset with another device, the device
must support Bluetooth Headset Profile, or Handsfree Profile.
Therefore, you cannot pair the headset with devices such as
regular cordless phones.
Our product satisfies Bluetooth Core Specification Version 2.0.
Some Bluetooth devices may not be compatible with your
headset. For further information about compatibility, please
contact the concerned manufacturer, or our customer service
center.
The sound often
breaks.
- The working distance for this headset is 10m from the
source. Please make sure you are within this distance.
※ In presence of obstacles (ex: wall) between the source
and the headset, the working distance may diminish.
- Machines such as cordless phones and wireless network
emit radio waves and may interfere with the headset.
Please use your headset far from these devices whenever
it is possible.
My headset doesn’t
work correctly.
Please turn off your headset for few seconds before using
again.
※ For any other problem, please contact our A/S Center, or the place of purchase.
Headset Specification
Bluetooth Version: V2.0 Class 2
Supported profiles: A2DP, AVRCP, HSP, HFP

Frequency spectrum: 2.4GHz Spectrum
Operating temperature: -20 ~ +70℃
Operating Time: Talk 10Hours / Music 9Hours
Standby time: 150 Hours
Working distance: 10m
Product Size: 38 x 42 x 13 mm
Product Weight: 28g
Utility Model
Registration Number 20-0411968 호
Patent Application
Number PCT/KR2006/001796