Ultra Max HTRUMXYQ12-3H User manual

4)
5)
6)
Please keep out of reach of young children.
During early use clicking may occur, this is
normal and is due to the expansion and
contraction of the heated objects in use.
For indoor use only, do not use outdoors.
sure to stop using it at once, send it to a
nearby approved appointed repair centre
authorized by the manufacturer.
Do not use the heater in a place where the
floor is not level or in an environment where
it is likely to be knocked over.
Do not use this unit overnight or while you
sleep. Otherwise make sure the unit is far
away from any objects such as textiles,
bedding ect. to avoid an accident.
Never touch the protector on the front when
the heater is on and/or still hot after
switching off, to avoid being burnt.
Only clean the heater when it is switched off
and unplugged. Be sure not to splash water
onto the unit or wipe with a wet cloth, as this
may cause it to short circuit.
Do not use the heater in the immediate
surroundings of a bath, a shower or a
swimming pool.
Do not use this heater with a program
controller, a timer or any other device that
switches the heater on automatically, since
a fire risk exists if the heater is covered or
displaced.
Do not cover the appliance as this causes a
fire risk.
If the power cord becomes damaged be
VI. IMPORTANT SAFETY MEASURES
1)
2)
3)
4)
5)
6)
7)
8)
To pull out the protector, first remove the
two fixing screws on the cover, then pull up
the cover and protector simultaneously.
To pull out the lattice net, first turn the stator
of the latice net vertical and then lightly pull
it out.
Clean the body frame and the reflector with
a damp, soft cloth with a small amount of
neutral detergent. Never clean the unit with
solutions such as benzine, thinner or polish
ect. Keep the reflector clean so that the
heat is reflected efficiently.
The honey comb guarding grill can be
cleaned with a small brush or vacuum
cleaner.
After cleaning assemble the unit in reverse
and make sure the unit is dry before use.
When not in use, clean and seal in a plastic
bag before storing in a dry place.
If malfunctions occur during its operation
please contact the supplier. Never disas-
semble or try to fix it yourself.
HALOGEN HEATER
INSTRUCTION MANUAL
HTRUMXYQ12-3H
1)
2)
3)
4)
5)
6)

Please read the instructions carefully before
use and keep for future reference.
Rated output
220-240V~50Hz
1. POWER SWITCH, UPPER HEATING AND
MIDDLE HEATING TUBE SWITCH
2. LOWER HEATING TUBE SWITCH
3. OSCILLATION SWITCH
4. TURN SWITCH
5. UPPER LID
6. LATTICE NET STATOR
7. HALOGEN HEATING TUBE
8. REFLECTOR
9. LATTICE NET
10. GUARDING GRILL
11. BODY
12. BASEPLATE
Please assemble the base plate to the main
body frame in the following sequence.
1) Unscrew the butterfly nuts on the bottom
of the body frame.
2) Pull out the power cord through the hole in
the centre of the base plate. To assemble
the base plate, match the projection in the
body frame with the indentation in the base
plate.
IV. OPERATION
1) Insert the plug into an electrical socket.
2) Set power supply switch on the “I” position
and the upper and middle heating tubes will
turn on. The other heating tubes can be
turned on by the other corresponding
switches.
3) Press the oscillation switch if you want
to swing the unit.
4) If you want to change the direction of the
body frame. Please hold the handle and turn
the body frame around slightly.
5) After use turn off all switches and pull out
plug from power supply.
Position the unit away from any objects by at
least 1m distance from the front and 0.5m
distance from the back. Please avoid placing
near any flammable objects and explosive
gases. Do not use in a wet environment to
prevent electric shock.
If the unit is not placed on level ground the tip
over safety switch may activate and prevent the
heater from being switched on. Therefore place
the unit on level ground when in use.
When using the heater always make sure the
power cord is at the back of the unit when
plugged into the socket, to avoid the power lead
from being damaged.
2.
3.
Baruch Enterprises Ltd., London, N18 2NG