Ultra-tow 43194 User manual

42 WATT LED TRIPLE BEAM
WORKLIGHT
OWNER’S MANUAL
WARNING:
Read carefully and understand all ASSEMBLY AND OPERATION
INSTRUCTIONS before operating. Failure to follow the safety rules and
other basic safety precautions may result in serious personal injury.
Item# 43194

Thank you very much for choosing an Ultra-Tow product! For future reference, please
complete the owner’s record below:
Model: _______________ Purchase Date: _______________
Save the receipt, warranty and these instructions. It is important that you read the entire
manual to become familiar with this product before you begin using it.
This worklight is designed for certain applications only. The distributor cannot be
responsible for issues arising from modification. We strongly recommend this worklight
not be modified and/or used for any application other than that for which it was designed.
If you have any questions relative to a particular application, DO NOT use the worklight
until you have first contacted the distributor to determine if it can or should be performed
on the product.
For technical questions please call 1-800-222-5381.
INTENDED USE
The 42W LED triple beam worklight is designed for trucks, SUVs, ATVs, farm equipment
and heavy machinery, with very low amp draw. It includes 14pcs LED Bulbs and a rocker
select switch that delivers 3 separate lighting options: spotlight, floodlight or spot/flood
combo, for exceptional versatility. Durable aluminum housing stands up to the elements
and round styling looks great and offers high performance.
TECHNICAL SPECIFICATIONS
GENERAL SAFETY RULES
WARNING: Read and understand all instructions. Failure to follow all instructions
listed below may result in serious injury.
CAUTION: Do not allow persons to operate or assemble this light until they have
read this manual and have developed a thorough understanding of how the light works.
Item
Description
Bulb Type
LED
Volts
9-32V
Beam Pattern
Spot, Flood, Spot/flood combo
Product Size
4-1/2in.L x 2-3/4in.W x 5in.H
Watts
42 Watt

WARNING:The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions or situations that could occur. It must be
understood by the operator that common sense and caution are factors that cannot be
built into this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY CONSIDERATIONS
•If mounting this product requires drilling holes, the installer MUST be sure that the
drilling process will not damage vehicle components or other vital parts. Check
both sides of the mounting surface before drilling begins. Also de-burr any holes
and remove any metal shards or remnants. Install grommets into all wire passage
holes.
•Do not install this product or route any wires in the deployment area of your air
bag. Equipment mounted or located in the air bag deployment area will damage or
reduce the effectiveness of the air bag, or become a projectile that could cause
serious personal injury or death.
•Do not use a pressure washer to clean this product.
WORKLIGHT USE AND CARE
•Do not modify the worklight in any way. Unauthorized modification may impair
the function and/or safety and could affect the life of the product.
•Always check damaged or worn out parts before using the work light.
Broken parts will affect the worklight operation. Replace or repair damaged or
worn parts immediately.
•Store idle worklight. If the worklight is not permanently installed, when the work
light is not in use, store it in a secure place out of the reach of children. Inspect it
for good working condition prior to storage and before reuse.
INSTALL THE WORKLIGHT
•Select a mounting location that will give you a maximum beam adjustment range
and will not cause any obstruction for your vehicle’s normal functions.
•Drill a mounting hole for mounting bolt (6) on the mounting surface. Insert
mounting bolt (6) to the middle hole of U bracket (2). Then run hexagon bolt (3)
from side hole of U bracket, light, then attach Washer (4) and nut (5). Adjust the
angle of the light body that will give you a maximum beam.

•Insert mounting bolt (6) on the U bracket (2) to the mounting surface (hole drilled).
Then attach the washer (7) and nut (8). Do not over tighten the screws.
INSTALL THE WIRES/SWITCH
•Disconnect the negative terminal of the vehicle’s battery. (This may require
resetting your radio, clock or other electronic devices when reconnected.)
•Find a convenient location near the bottom of dash board to mount the switch. A
square hole (2-7/8”x 1-7/8”) should be cut out from the board. Route the Input and
output wires through the square hole. Then squeeze the switch into the square
hole.
•Follow the “WIRING DIAGRAM”below, Connect two wires to battery (white wire
to positive terminal, and black wire to the negative terminal). Connect other three
wires of the switch to light. Marked on the wires. If connect all components need
harness, ensure has 10Amp fuse on the harness to protect the light and vehicle.
•Reconnect the negative terminal to the battery and turn on the switch to test the
whole system. If both of the lights do not come on, inspect the system in the
following series: fuse/ ground wire/ battery connection/ switch/ lamp connection/
relay. Replace the defective parts if necessary.
•With the system on, visually check the light beam, then turn off the switch and
adjust the lamps’ angle. Repeat this adjustment until a proper light beam appears,
then firmly tighten all screws of the light unit.
OPERATION
Connect switch to light and 9-32V power supply. There are three buttons in the
switch, which are marked “Power,””Spot,””Flood.”
Press “power”and “Spot”, the light delivers a spot beam.
Press “power”and “Flood”, the light delivers a flood beam.
Press “power”, “Spot”and “Flood”, the light delivers the spot/flood combo beam.
MAINTENANCE
•It is recommended that the general condition of the worklight be examined before
it is used. Keep your worklight in good repair by adopting a program of
conscientious repair and maintenance. Have necessary repairs made by qualified
service personnel.
•Clean the surface of worklight lens frequently to keep its brightness.
•When any malfunction occurs, stop using and repair it immediately as soon as
possible. Please operate your worklight according to the proper operation
procedures.

WIRING DIAGRAM

PARTS DIAGRAM
1
2
3
4
5
6
7
8
Light body
Bracket
M8x65 hexagon bolt
M8 spring washer
M8 hexagon nut
M10x25 hexagon bolt
M10 spring washer
M10 hexagon nut
Part # Description Qty.
1
1
1
1
1
1
1
1
PARTS LIST
Part#
Description
Qty.
1
Light Body
1
2
Bracket
1
3
M8x65 hexagon bolt
1
4
M8 spring washer
1
5
M8 hexagon nut
1
6
M10x25 hexagon bolt
1
7
M8 spring washer
1
8
M8 hexagon nut
1
9
Switch
1
For replacement parts and technical questions, please call 1-800-222-5381.

WARRANTY
One year limited warranty
Distributed by:
Northern Tool + Equipment Co., Inc.
Burnsville, Minnesota 55306
NorthernTool.com
Made in China