Uniden Bearcat 980 SSB User manual

Owner’s Manual
Printed in Vietnam
U01UT563ZZZ(0)
®980 SSB

CONTENTS
SAFETY NOTICE .......................................................................... 4
UNPACKING ................................................................................ 5
DESCRIPTION ............................................................................. 5
EMERGENCY OPERATION ......................................................... 5
CONTROLS AND FUNCTIONS.................................................... 6
INSTALLATION............................................................................ 9
MOBILE INSTALLATION .............................................................................. 9
Mobile Antenna........................................................................................... 9
Connecting the Power Cords .................................................................... 10
Ground Information ................................................................................. 10
INSTALL 6-PIN TO 4-PIN ADAPTER ........................................................... 10
MARINE INSTALLATION ............................................................................. 11
USING YOUR BEARCAT 980 SSB ............................................. 11
CB MODE...................................................................................................... 11
BASIC SETTINGS......................................................................................... 11
ALL CHANNEL SCAN................................................................................... 12
WEATHER MODE (WX MODE) .................................................................... 12
Set Weather Alert Mode............................................................................ 13
MEMORY Mode.......................................................................................... 13
Save Channels Into Memory..................................................................... 13
Scan Channels in Memory ........................................................................ 13
Listen to Channels in Memory .................................................................. 13
Clear Channels from Memory................................................................... 14
MENUS ......................................................................................................... 14
Select Display Mode (Day/Night) ............................................................. 14
Select Backlight Color............................................................................... 14
Set LCD Contrast ....................................................................................... 15
Set Brightness ........................................................................................... 15
Diagnostic Menus ..................................................................................... 15
Battery Check............................................................................................ 16

Uniden is a registered trademark of Uniden America Corporation.
Bearcat is a registered trademark of Uniden America Corporation.
Features, specications, and availability of optional accessories are all
subject to change without notice..
Antenna Mismatch Check......................................................................... 16
RF Power Check......................................................................................... 16
EXIT Menu.................................................................................................. 16
OTHER FEATURES ....................................................................................... 17
S/RF/CAL/SWR Meter ................................................................................ 17
Calibrate Standing Wave Ratio (SWR) ..................................................... 17
PREVENTIVE MAINTENANCE .................................................. 17
MAINTENANCE ......................................................................... 17
TROUBLESHOOTING ............................................................... 18
SERVICING YOUR TRANSCEIVER ........................................... 19
SPECIFICATIONS....................................................................... 19
TWO-YEAR EXTENDED WARRANTY ...................................... 21
RADIO CODE DEFINITIONS ..................................................... 23

E-4
SAFETY NOTICE
The antenna used for this radio must be properly installed and
maintained and must provide a separation distance of at least 59 cm
(23.2 inches) from all persons and must not be collocated or operated in
conjunction with any other antenna or transmitter. Never transmit if any
person is closer than the specified distance to the antenna.
Note that Uniden does not specify or supply any antenna with this
transceiver. While a 0 dBi gain antenna is normal for a typical installation,
the above limit applies to any antenna with up to 3 dBi gain.
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation
of the device.
Changes or modifications to this product or use of accessories not
expressly approved by Uniden, or operation of this product in any way
other than as provided in the Uniden Owner’s Manual could void your
authority to operate this product.
L’appareil est conforme aux normes d’Industrie Canada. Son
fonctionnement est soumis aux deux conditions suivantes : (1) Ce
dispositif ne doit pas causer d’interférences et (2), il doit pouvoir accepter
les interférences, incluant celles pouvant nuire à son fonctionnement
normal.
Tous les changements apportés à cet appareil, s’ils ne sont pas
expressément approuvés par Uniden ou toute utilisation de celui-ci
d’une autre manière que celle décrite dans ce guide peut annuler votre
autorisation de le faire fonctionner.
.

E-5
UNPACKING
Your Bearcat 980 SSB contains the following:
Bearcat 980 SSB CB 2-way mobile radio
Microphone
Mounting Bracket Kit
DC Power Cord
6-pin to 4-pin microphone adapter
Owner’s Manual
Part 95 Subpart D (FCC Rules)
If any items are missing or damaged, contact your place of purchase
immediately.
DESCRIPTION
Your Uniden Bearcat 980 SSB represents the highest quality
communications device designed for use in the Citizens Band Radio
Service. It will operate on any of the 40 AM frequencies authorized by the
Federal Communications Commission (FCC).
The Citizens Band Radio Service is under the jurisdiction of the Federal
Communications Commission (FCC). Any adjustments or alterations
which would alter the performance of the transceiver’s original FCC type
acceptance, or which would change the frequency determining method, are
strictly prohibited.
Replacement or substitution of crystal, transistors, ICs, regulator
diodes, or any other part of a unique nature, with parts other than those
recommended by Uniden, may cause violations of the technical regulations
in Part 95 of the FCC Rules or in violation of type acceptance requirements
in Part 2 of the rules.
EMERGENCY OPERATION
1. Press 9/19/NORM or turn Channel Selector knob to Channel 9.
2. Press PTT on the microphone and speak clearly.
3. If there is no response, select an active channel and ask that party
to relay your emergency broadcast on Channel 9.

E-6
All channels except Channel 9 may be used for normal communication. The
FCC reserves Channel 9 for emergencies involving the immediate safety of
individuals or protection of property. Use Channel 9 to render assistance to
a motorist. This is an FCC rule and applies to all CB radio operators.
CONTROLS AND FUNCTIONS
1. Volume Control knob with Power On/O. Turn the knob
clockwise until it clicks to turn power on. Continue turning the
knob clockwise to increase the volume. Turn the Volume Control
knob counterclockwise to decrease the volume or until it clicks to
turn power o.
2. SQUELCH knob: Reduces background noise when there is no
incoming signal.
3. S/RF/CAL/SWR Meter: Displays Receive signal strength, RF Power,
and SWR reading.
4. Channel Number display.
5. Operation buttons and associated LEDs:
Talkback: Talkback lets you monitor yourself when transmitting.
Press Talkback to activate the function (LED = on). With Talkback
active, press and hold the PTT button and adjust the talkback
volume with the Channel Selector knob. (Levels 01 - 15). The LED
will stay on for 5 seconds after you release the PTT button.
RF Gain: Adjusts receive signal sensitivity. With RF Gain active,
14 2 5 6
7151413
11
10
98 12
3
16

E-7
press and hold the PTT button and adjust the gain levels with the
Channel Selector knob. (Levels 1 - 5). The LED will stay on for 5
seconds after adjusted.
MIC Gain: Adjusts microphone gain. Delivers up to 100%
modulation. With MIC Gain active, press and hold the PTT button
and adjust the gain levels with the Channel Selector knob.
(Levels 1 - 4). The LED will stay on for 5 seconds after you release
the PTT button.
Weather: Press to toggle between Weather and CB channels. Turn
Channel Selector to cycle through the 7 weather channels. (LED
o = CB channels; LED on = Weather channels).
Press and hold to turn Weather Alert on and o. ALERT displays.
6. Channel Selector/MENU/OK. Press the inner MENU/OK button to
select a menu option or other selection. Turn the outer Channel
Selector knob to:
Select channels.
Select Night or Day Modes. Press MENU/OK to set up your
preferred day and night mode settings.
Select menu modes.
Change scan resume direction (up or down).
Control Talkback volume.
Control RF gain.
Control Mic gain level.
All channels except Channel 9 may be used for normal communication. The
FCC reserves Channel 9 for emergencies involving the immediate safety of
individuals or protection of property. Use Channel 9 to render assistance to
a motorist. This is an FCC rule and applies to all CB operators.
7. Microphone socket.
8. Indicators turn on when the function is turned on.
9. S/RF/CAL/SWR: Press to check RF signal strength, calibration, and
SWR reading.
10. CB/PA: Selects CB (Citizens Band) or PA (Public Address).
Do not use the PA function unless an external speaker is connected.

E-8
11. MEM/SCAN: Press to start or stop scanning modes [All Channel
Scan (see page 12) and Memory Scan (see page 12)]. Press and hold
to set or clear channel memory while in Memory mode.
12. 9/19/NORM: Press to switch between emergency channel 9,
channel 19, and standard CB channels.
13. Frequency Display: Displays the MHz of the selected channel. Also
displays menu options.
14. ANL/NB: Provides 3-way control of ANL (Automatic Noise
Limiter) or NB (Noise Blanker) features — ANL on, NB on, or both
ANL and NB on or o. ANL reduces external noise. NB reduces
interference from vehicle ignition systems. Press and hold for one
second to turn key beep tone on and o.
Use this button to turn key beep on and o. Press and hold until BP ON
or BP OFF displays.
AM/USB/LSB: Three-way switch to select AM, USB or LSB
operation.
15. Clarier: 1.5 kHz. Adjust Receive Frequency without changing the
transmitter frequency (Fine and Course adjustment).
17 18 19
20
21
22
16. Antenna socket: Connects antenna to the unit.
17. PA SP: Connects optional external 8-ohm, 4-watt speaker for use
as a public address system.
To prevent acoustic feedback, separate the microphone from the speaker
when operating the PA at high output levels.
18. EXT. SP: Connects 8Ω 4W speaker to remotely monitor receiver.

E-9
When the external speaker is plugged in, the internal speaker is o.
19. POWER +12 VDC: Connects DC power to transceiver.
20. FUSE 6A: Provides circuit protection to transceiver. Inline
replaceable.
21. PTT: Push-to-Talk. Push microphone button.
INSTALLATION
MOBILE INSTALLATION
Plan the location of the transceiver and microphone bracket before
beginning installation.
1. Select a location that is convenient for operating the radio but
does not interfere with the driver or passenger.
2. Install bracket with self-tapping screws provided.
3. Connect the power cords (see below).
4. Attach the microphone bracket to side of the radio or car dash.
5. Attach radio to bracket.
Mobile Antenna
Because the maximum power output of the transmitter is limited by
the FCC, the quality of your antenna is very important. To achieve the
maximum transmission distance, Uniden strongly recommends that you
install only a high quality antenna. You have just purchased a superior
transceiver; don't diminish its performance by installing an inferior
antenna.
Only a properly matched antenna system will allow maximum power
transfer from the 50-ohm transmission line to the radiating element.
Your Uniden dealer is qualified to help you select the proper antenna for
your requirements. A whip style antenna may be used for automobile
installation.

E-10
A short “loaded” whip antenna is easier to install on an automobile, but
its efficiency is less than that of a full quarter-wave whip antenna.
Connecting the Power Cords
Uniden recommends connecting the power lead to the Ignition Switch
Accessory Terminal. This way, the transceiver is automatically turned off
when the ignition switch is turned off.
As an alternative, the power cord may be connected to an available
terminal on the fuse block or to a point in the wiring harness. However,
caution must be taken to prevent a short circuit. If in doubt, contact your
vehicle dealer for information.
Ground Information
This transceiver may be installed and used in any 12-volt DC negative
ground system vehicle.
Negative Ground System
With a negative ground system, the negative (-) battery terminal is
usually connected to the vehicle motor block.
Connect the red DC power cord from the
transceiver to the positive (+) battery terminal
or other convenient point. Then connect the
black power cord to the vehicle chassis or negative (-) battery terminal.
INSTALL 6-PIN TO 4-PIN ADAPTER
The Bearcat 980 SSB is pre-configured for Uniden’s new 6-pin wireless,
noise-cancelling technology, available in 2012. Your Bearcat 980 SSB
comes with an adapter to connect the radio’s 6-pin microphone jack to
an aftermarket 4-pin microphone.
1. Insert the 6-pin side of the adapter into the Bearcat 980 SSB 6-pin
microphone jack connection.

E-11
2. Plug a 4-pin microphone connector into the 4-pin side of the
adapter.
MARINE INSTALLATION
Consult your dealer for information regarding marine installation. It is
important to adequately ground the system and to prevent electrolysis
between the fittings in the hull and the water.
USING YOUR BEARCAT 980 SSB
CB MODE
Be sure that the power source, antenna, and microphone are properly
connected before proceeding.
BASIC SETTINGS
1. Turn unit on. Set volume to a comfortable level.
2. Select channel.
3. Set noise limitations as desired (ANL or NB or both).
4. Adjust Squelch.
• Turn SQUELCH fully clockwise to receive strong signals.
• Turn SQUELCH fully counterclockwise until you hear a hiss. All
get through — noise, weak signals, and strong signals.
• Turn SQUELCH back clockwise until the hiss stops. Only
clearer signals get through.
Set SQUELCH only when the radio is not receiving a strong signal.
5. Press RF Gain to set RF gain.
6. Press MIC Gain then press PTT and turn the main control to
adjust microphone sensitivity, up to 100% modulation between
1 - 4.
7. Set Backlight color (see page 14).
8. Set LCD Contrast (see page 15).
9. Set Brightness (see page 15).

E-12
ALL CHANNEL SCAN
When All Channel Scan is on, the radio scans channels until it receives a
signal. It moves to the next channel if it receives no signal after 3 seconds.
1. Press MEM/SCAN twice if in CB mode (once if in MEM mode).
SCAN displays.
2. The radio begins scanning upward through the channels.
• To skip the channel the radio has stopped on, turn Channel
Selector clockwise to move to the next channel or counter-
clockwise to move to the previous channel. The radio
continues scanning in the selected direction.
• To change to Memory Channel Scan mode, press MEM/SCAN
while in All Channel Scan mode (see page 10).
3. To exit All Channel Scan mode, press PTT, 9/19/NORM, WEATHER,
or CB/PA.
WEATHER MODE (WX MODE)
Your radio combines a CB radio with a Weather radio and a Weather
Alert system. The Weather Alert system sounds a 7-second signal in the
event of severe weather when in CB mode. The Weather radio continually
broadcasts weather conditions when you are in Weather mode.
1. Press WEATHER. Your radio is now in Weather radio mode.
2. Select 1 of 7 weather channels using Channel Selector.
You cannot change ANL or NB settings while in WX mode. The radio will
sound an alert tone.
Set Weather Scan Mode
Weather Scan mode allows the radio to move to the next weather
channel if no signal is detected after 3 seconds. Set Weather Scan mode
to ON or OFF through the menus.
1. Press MENU/OK to activate the menus. DAY/NT displays.
2. Turn the Channel Selector knob to cycle through the menu op-
tions until WXSCAN displays.
3. Press MENU/OK. ON displays.

E-13
4. Press MENU/OK to set Weather Scan mode to ON or turn the selec-
tion knob until OFF displays and then press MENU/OK to set it.
WXSCAN displays again.
If Weather Scan is ON when you turn o the radio, it remains ON.
Left at these settings (WX mode, WX Scan), you will hear only weather
broadcasts and Weather Alert signals. To use your CB radio normally
while monitoring weather alerts, press WEATHER again.
Set Weather Alert Mode
Weather Alert mode only operates when you are in CB mode; it does not
operate in Weather mode. In CB mode, the radio sounds an alert tone
when it detects a 1050Hz tone on a weather channel.
Press and hold WEATHER to turn Weather Alert on. ALERT displays.
MEMORY MODE
You can store channels into memory and then scan only those channels.
Save Channels Into Memory
1. Tune to a channel in CB mode.
2. Press and hold MEM/SCAN until SAVE appears (about 2 seconds).
3. Release MEM/SCAN.
4. The radio stays on the saved channel.
Scan Channels in Memory
1. From All Channel Scan mode (see page 12), press MEM/SCAN
until MEM and SCAN display; the radio scans memory channels
only.
2. Press MEM/SCAN again to return to MEMORY mode or the last
channel scanned.
Listen to Channels in Memory
1. Press MEM/SCAN until MEM displays.
2. Turn the Channel Selector knob to hear the channels you saved.

E-14
Clear Channels from Memory
1. In MEM mode, select a channel.
2. Press and hold MEM/SCAN until CLEAR displays.
3. Release MEM/SCAN. The radio plays the next channel in memory.
MENUS
Access menus by pressing MENU/OK. The first menu selection is Day
or Night setting. Turn the Channel Selector knob to change the Day or
Night setting.
Press MENU/OK again for:
Day/Night - display intensity
COLOR - Backlight color
CONT - LCD Contrast
BRIGHT - Brightness
WXSCAN - Weather Scan mode
DIAG - Diagnostics
– Battery Check
– Antenna Mismatch Check
– RF Power Check
Exit
Select Display Mode (Day/Night)
1. Press MENU/OK to access Day or Night selection.
2. Select Day or Night mode setting.
3. Press MENU/OK to activate your selection.
Select Backlight Color
1. Press MENU/OK to select Day or Night setting and then press
MENU/OK again to activate your selection.
2. Press MENU/OK to activate the menus. Turn Channel Selector
until COLOR displays.
3. Press MENU/OK. Turn Channel Selector until DAY displays.
4. Press MENU/OK. DAY blinks.
5. Turn Channel Selector to cycle through the available backlight
colors or o (none). The selection number for that color displays

E-15
in that color. The available colors are:
Option
No: Color Option No: Color
1 Blue 5 Magenta
2 Green 6 Yellow
3Cyan 7 White
4 Red
6. Press MENU/OK to select a color. COLOR displays.
7. Repeat these procedures to set the NIGHT backlight color.
Set LCD Contrast
1. Press MENU/OK to activate the menus. Turn Channel Selector
until CONT displays.
2. Press MENU/OK. Turn Channel Selector until DAY displays.
3. Press MENU/OK. DAY blinks.
4. Turn Channel Selector to cycle through the contrast options.
(Lowest = 01; Highest = 15)
5. Press MENU/OK to select the one you want. CONT displays again.
6. Repeat these procedures to set the NIGHT contrast level.
Set Brightness
1. Press MENU/OK to activate the menus. Turn Channel Selector
until BRIGHT displays.
2. Press MENU/OK. DAY displays.
3. Press MENU/OK. DAY blinks.
4. Turn Channel Selector to cycle through the brightness options.
(Lowest = 01; Highest = 15)
5. Press MENU/OK to select the one you want. BRIGHT displays again.
6. Repeat these procedures to set the NIGHT brightness level.
Diagnostic Menus
1. Press MENU/OK to activate the menus.
2. Turn Channel Selector until DIAG displays.
3. Press MENU/OK to enter the DIAG level.
From the DIAG level, you can check battery power levels, antenna
mismatch and RF power levels.

E-16
Battery Check
Check the DC power levels if you feel your radio is not performing
properly.
1. Once DIAG displays, press MENU/OK; VOLT displays.
2. Press MENU/OK; the battery voltage displays for 2 seconds and
then the battery voltage condition displays:
– PASS - Voltage is good.
– FAILLO - Voltage is too low.
– FAILHI - Voltage is too high.
3. Press MENU/OK to return to the DIAG level.
Antenna Mismatch Check
An antenna mismatch indicates that reception quality may be impaired.
1. Once DIAG displays, press MENU/OK; VOLT displays.
2. Turn Channel Selector until ANT displays.
3. Press MENU/OK. GO PTT displays.
4. Press and hold PTT. The Antenna Mismatch condition, PASS or
FAIL, displays.
5. Release PTT and press MENU/OK to return to the DIAG level.
RF Power Check
RF alerts indicate that the transmission levels are not acceptable.
1. Once DIAG displays, press MENU/OK; VOLT displays.
2. Turn Channel Selector until RF OUT displays.
3. Press MENU/OK. GO PTT displays.
4. Press and hold PTT. The RF power condition, PASS or FAIL,
displays. (If FAIL displays, see the Troubleshooting section, page 18.)
5. Release PTT: GO PTT displays.
6. Press MENU/OK to return to the DIAG level.
EXIT Menu
Exit the menus from the main menu levels (COLOR, CONT, BRIGHT,
WXSCAN, and DIAG). From this level, turn Channel Selector until EXIT

E-17
displays. Press MENU/OK. The radio returns to the last operating
mode and channel.
OTHER FEATURES
S/RF/CAL/SWR Meter
You can check your incoming signal strength and output power as
you use your Bearcat 980 SSB. The 12-column LCD display (refer to
item number 3 on page 6) displays this data. Press and hold PTT on
the microphone to see the RF output power levels. Release PTT to see
incoming signal strength.
Calibrate Standing Wave Ratio (SWR)
Check and calibrate the SWR to ensure your antenna system is properly
tuned.
1. Connect the antenna.
2. Turn Channel Selector to set the channel .
3. Press S/RF/CAL/SWR until CAL displays.
4. Press and hold PTT, then rotate the Channel Selector until the
bar graph meter is at the CAL point.
5. Press PTT and note the SWR reading. If the reading is > 1.5, follow
your antenna’s instructions to adjust the antenna length. Then,
repeat this step.
PREVENTIVE MAINTENANCE
Every six months:
1. Check the SWR.
2. Be sure all electrical connections are tight.
3. Inspect antenna coaxial cable for wear or breaks in shielding.
4. Be sure all screws and mounting hardware are tight.
MAINTENANCE
The Bearcat 980 SSB is designed to give you years of trouble-free service.
There are no user-serviceable parts inside. It requires no maintenance
except replacing the inline fuse in the fuse holder of the DC power cord.

E-18
To replace a blown fuse:
1. Press ends of the fuse holder together. Twist to open. Carefully
separate the two pieces.
2. Remove the fuse and inspect. If blown, replace with the same
type 6-amp fuse.
Use only the fuse specied for your Bearcat 980 SSB. Failure to do so may
void your warranty.
TROUBLESHOOTING
In the event of system malfunction, perform the following procedures:
Problem Suggestion
Unit does not power up Check power cord connections.
Check fuse.
Check vehicle electrical system.
No reception Check microphone connection.
Set CB/PA to CB.
Check VOLUME and SQUELCH.
Check antenna.
Check antenna connection.
Adjust RF Gain.
Poor Reception Check VOLUME and SQUELCH.
Be sure antenna SWR is normal.
Adjust RF Gain.
No Transmission Set CB/PA switch to CB.
Check microphone connection.
Adjust MIC Gain.
Low Transmission Adjust MIC Gain.
Using MEM/SCAN does not
access channels in memory
Verify that there are channels saved into
memory.
Unit does not work as well as
previously.
Turn the power o then back on. The channels
will reset.
Battery power check returned
FAILLO or FAILHI.
Make sure your power wires have a good
connection.
Check your battery charge; it needs to be fully
charged. Lower voltage will cause a failure.
Check your alternator.

E-19
Problem Suggestion
Antenna check returned FAIL.Make sure your antenna ground is good.
Check for damage to the antenna.
Check the SWRs at a CB shop. High SWRs will
damage the radio.
RF power diagnosis check
returned FAIL.
Make sure your antenna ground is good.
Check for damage to your antenna.
Check the antenna connection on the back of
the radio. Be sure it is tight.
If you do not get satisfactory results after performing these checks, call
the Uniden Customer Service Center at 1-800-297-1023, 8:00 a.m. to 4:30
p.m. CST, Monday through Friday.
SERVICING YOUR TRANSCEIVER
Technical information, diagrams, and charts are provided on request. It
is the user's responsibility to see that this radio is operating at all times
in accordance with the FCC Citizens Radio Service regulations. We highly
recommend that you consult a qualified radio/telephone technician for
servicing and aligning this CB radio product.
When ordering parts, be sure to specify the correct model number and serial
number of the unit.
SPECIFICATIONS
GENERAL
Channel: 40 AM/USB/LSB
Frequency Range: CB : 26.965 - 27.405 MHz
WX : 162.400 - 162.550 MHz
Emission Emission AM/USB/LSB
Frequency Control: PLL Synthesizer
Antenna Impedance: 50 ohms
Power Input: 13.8VDC
Current Drain
TX: AM full modulation 2.2A (max.)
SSB full power output 4A (max.)

E-20
RX: At no signal: 650 mA
Operating Temperature: -22°F to 140°F (-30°C to 60°C)
Accessories: DC Power Cord
Noise Cancelling Microphone
Microphone Hanger
Mounting Bracket
Size (W x D x H): 7.25 in. x 7.5 in. x 2.25 in.
(without knobs and jacks)
(184.149 mm x 190.50 mm x 57.15
mm)
Weight: 2.2 Pounds
TRANSMITTER
Output Power: AM: 4 watts; USB/LSB 12 W PEP SSB
Hum and Noise: Better than 40 dB
Frequency Tolerance: ±0.002%
Modulation Percentage (Peak): 100%
Spurious Rejection: -70 dB
Output Impedance: 50 ohm, unbalanced
Unwanted Sideband -55 db
RECEIVER
Sensitivity at 10 dB S+N/N: AM: 0.5 µV; USB/LSB: 0.25 µV
Sensitivity at 500 mW Audio Output: 0.5 µV
Squelch Threshold: 0.5 µV
Antenna Impedance: 50 ohms
Squelch Tight: 1000 µV
Signal Meter S-9: 100 µV
Audio Output Power (max.): 3 watts
Audio Output (10% Distortion): 2.5 watts
Clarier Range 1.5 kHz
Adjacent Channel Rejection: 60 dB
Image Rejection: 80 dB
Internal Speaker Impedance: 16 ohms
External Speaker Impedance: 8 ohms
PUBLIC ADDRESS
Output Power at 10% Distortion: 2.5 watts
Specifications shown are typical and subject to change without notice.