Uninterruptible Power Supplies PowerWAVE 8000DPA RI User manual

User Manual
PowerWAVE
8000DPA RI
Pioneering solutions for
total power protection

UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013

UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013
Document Control
ISSUE DATE REVISION SUMMARY
1.0 09-09-09 Initial issue.
1.1 01-02-11 Reference number changed to 338-01-00
1.2 10-06-11 Updated to clarify rear access requirements
1.3 15-11-11 Added R1-40 module and general update.
1.3.1 30-05-12 Corrected landscape header error
1.4 05-04-13 Updated contact details
1.4.1 05-04-13 Updated 24 hour contact details

UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013

UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013 i
Table of Contents
1 Safety
1.1 Description of symbols used in this manual 1-1
1.2 User precautions 1-1
2 General Description
2.1 Reliability and Quality Standards 2-1
2.2 PowerWAVE 8000-RI DPA System 2-1
2.3 System configuration 2-1
2.4 Advanced Design Features 2-2
2.4.1 Input booster technology 2-2
2.4.2 Flexible battery management 2-3
2.4.3 Decentralized Parallel Architecture (DPA) 2-3
2.5 Warranty 2-3
2.6 Extended Warranty 2-4
2.7 Additional Service/Maintenance Support 2-4
3 Installation
3.1 Introduction 3-1
3.2 Receipt of the UPS 3-1
3.2.1 Site transportation 3-1
3.3 Unpacking 3-2
3.3.1 Nameplate 3-2
3.4 Batteries 3-2
3.5 Storage 3-2
3.5.1 UPS Module 3-2
3.5.2 Battery 3-3
3.6 Positioning 3-3
3.6.1 Planning the installation 3-3
3.6.2 Heat Dissipation With Non-linear Load (per module) 3-4
3.7 Rack Assembly 3-4
3.8 UPS Power Cabling (preparation and planning) 3-13
3.8.1 General requirements 3-13
3.9 Connecting the UPS input/bypass supply 3-16
3.9.1 Safety notes 3-16
3.9.2 Preparing the input cabling 3-16
3.9.3 Connecting the UPS input power cables 3-16
3.10 Connecting the UPS output supply 3-17
3.10.1 Safety notes 3-17
3.10.2 Preparation for the output cabling 3-18
3.10.3 Connecting the UPS output cables 3-18
3.11 Connecting the Batteries 3-18
3.11.1 Safety notes 3-18
3.11.2 Battery configuration options 3-18
3.11.3 Battery cabling 3-21
3.11.4 Connecting the batteries 3-22

:
-ii UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013
3.12 Module interfacing facilities 3-23
3.12.1 Smart Port JD1 (Serial RS 232) and USB Port 3-23
3.12.2 X1 & X2 Dry Port (volt-free contacts) 3-24
4 Operation
4.1 Commissioning 4-1
4.2 Operator Control Panel 4-1
4.2.1 Power Management Display (PMD) 4-2
4.2.2 Mimic LED indicators 4-2
4.3 Description of the LCD display 4-3
4.3.1 Status screens 4-3
4.3.2 Main menu screen 4-4
4.3.3 Event log menu screen 4-4
4.3.4 Measurements menu screen 4-4
4.3.5 Commands menu screen 4-5
4.3.6 UPS Data menu screen 4-6
4.3.7 Set-Up Service menu screen 4-6
4.3.8 Set-up User menu screen 4-6
4.3.9 Set-Up Service menu screen 4-7
4.4 Operating Modes 4-7
4.4.1 On-Line (Inverter) mode 4-7
4.4.2 Bypass (Line-Interactive) Mode 4-7
4.4.3 Maintenance Bypass Mode 4-8
4.5 Operating Instructions 4-9
4.5.1 Starting the UPS system from the Maintenance Bypass 4-9
4.5.2 Individual UPS Module start/stop procedure 4-11
4.5.3 Transfer to Maintenance Bypass Mode 4-12
4.5.4 Complete system shutdown 4-14
4.6 Replacing a UPS Module in a Single Module System 4-15
4.6.1 Extracting the UPS Module 4-15
4.6.2 Refitting the UPS Module 4-15
4.7 Replacing a UPS Module in a REDUNDANT Multi-Module System 4-16
4.7.1 Extracting the UPS Module 4-16
4.7.2 Refitting the UPS Module 4-17
4.8 Replacing a UPS Module in a CAPACITY Multi-Module System 4-17
4.8.1 Extracting the UPS Module 4-17
4.8.2 Refitting the UPS Module 4-18
5 Maintenance
5.1 Introduction 5-1
5.2 System calibration 5-1
5.3 User responsibilities 5-1
5.4 Routine maintenance 5-1
5.5 Battery Testing 5-2
5.6 Battery Maintenance 5-2
5.7 Battery Disposal and Recycling 5-2
6 Troubleshooting
6.1 Alarms 6-1
6.2 Menu, Commands, Event Log, Measurements, 6-1
6.3 Fault Identification and Rectification Messages and Alarms 6-2
6.4 Contacting Service 6-2
7 Options
7.1 Introduction 7-1

UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013 -iii
:
7.2 Remote Emergency Stop 7-1
7.3 Generator ON facilities 7-2
7.4 WAVEMON Shutdown and Management Software 7-2
7.4.1 Why is UPS Management important? 7-2
7.4.2 WAVEMON Shutdown and Monitoring Software 7-2
7.5 SNMP CARD/ADAPTOR For Network Management/Remote Monitoring 7-4
7.6 Modem/Ethernet card / PowerREPORTER™ management software 7-6
8 Specification
8.1 Mechanical Characteristics – Subracks 8-1
8.2 Input Characteristics 8-2
8.3 Battery Characteristics 8-3
8.4 Battery Capacity Usage 8-3
8.5 Output Characteristics 8-3
8.6 Heat Dissipation With Non-linear Load (per module) 8-3
8.7 Environmental Characteristics 8-4
8.8 Standards 8-4
8.9 Communication Options 8-5
8.10 Fuses & Cables Quick Reference 8-6

:
-iv UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013

UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013 1-1
1Safety
1.1 Description of symbols used in this manual
1.2 User precautions
WARNING: The warning symbol is used where there is danger of an electrical shock,
equipment damage or personal-injury.
CAUTION: The caution symbol is used to highlight important information to avoid possible
equipment malfunction or damage.
WARNING: Keep this manual with the UPS for future reference.
WARNING: The UPS and peripheral equipment must be installed and commissioned by
suitably qualified and trained personnel who are aware of the potential shock hazards.
WARNING: Do not attempt to install this UPS system until you are satisfied that ALL the safety
instructions and hazard warnings contained in this manual are read and fully understood.
WARNING: High leakage current!
Ensure that the UPS has been correctly earthed before you connect the mains power supply!
WARNING: This UPS must not be started-up or put into use without having first been
commissioned by a fully trained engineer authorised by the manufacturer.
WARNING: All servicing must be performed by qualified personnel. Do not attempt to service
the UPS yourself.
You run risk of exposure to dangerous voltages by opening or removing the UPS-covers!
Uninterruptible Power Supplies Ltd will assume no responsibility nor liability due to incorrect
operation or manipulation of the UPS.
WARNING: The PowerWAVE 8000-RI DPA is a Class A UPS product
(according to EN 62040). In a domestic environment the UPS may cause radio interference. In
such an environment the user may be required to undertake additional measures.

1: Safety
1-2 UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013

UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013 2-1
2General Description
2.1 Reliability and Quality Standards
Congratulations on your purchase of the PowerWAVE 8000-RI DPA.
Using a unique modular construction the PowerWAVE 8000-RI DPA represents a completely new generation
of medium power, 3 phase UPS-Systems, incorporating the latest technological developments in power
engineering. High reliability, upgrade ability, low operating costs and excellent electrical performance are only
some of the highlights of this innovative UPS solution.
Uninterruptible Power Supplies Ltd specialises in the design, building, installation and maintenance of
Uninterruptible Power Systems. This compact and powerful UPS is just one example of our wide range of
state-of-the-art power protection devices and will provide your critical equipment with a steady and reliable
power supply for many years.
The criteria and methods which are used in the design, manufacture, and maintenance of Uninterruptible
Power Supply systems are certified to International Standard ISO 9001/EN 29001 and ISO 14001. A full UPS
Specification is given in Chapter 8 of this manual.
2.2 PowerWAVE 8000-RI DPA System
The PowerWAVE 8000-RI DPA is a truly modular, rack-mountable system based on 10kVA or 20kVA UPS
modules. The system can be based around a single 10kVA or 20kVA module or two (or more) modules
connected in parallel and configured to operate as a redundant or increased capacity system.
The system comprises a 19 inch sub-rack assembly containing the UPS Module(s), switch panel, battery
tray(s), power connectors, and a range of communication I/O facilities.
2.3 System configuration
Figure 2.1 illustrates the available sub-rack configurations populated with either 1 or 2 UPS modules.
Thanks to the advanced PowerWAVE 8000-RI DPA system design, it is possible to operate a dual module
system with only a single module fitted and add the second module at a later time to increase the system
capacity along with a future increase in load demand. This ‘hot-swappable’ design also allows modules to be
exchanged while the equipment is running during troubleshooting and repair procedures without the need to
put the load to ‘bypass’ (of course, depending on system redundancy and demanded load).
Key Point: All the modules fitted within a cabinet must be of the same rating – i.e. it is not possible
to mix 10kVA and 20kVA modules in the same parallel system.

2: General Description
2-2 UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013
Figure 2.1 PowerWAVE 8000-RI DPA module configuration
2.4 Advanced Design Features
2.4.1 Input booster technology
The UPS module’s inbuilt advanced booster technology results in a perfect sinusoidal input power quality at
0.99 input power factor with a harmonic content of 3% THD(i). This leads to a more reliable total system
operation and savings in generator and transformer sizing as losses in the windings are minimised. It also
means that traditional harmonic filters are no longer required.
The high power factor presented by the UPS on the incoming mains supply minimises cabling and fusing
costs due to the resulting lack of reactive power consumption. This, together with the accompanying low
harmonic currents, provide the following benefits:
• No additional losses in wires and cables.
• No extra heating of transformers and generators.
• No over sizing of generators.
• No false circuit breaker tripping and malfunction.
• No erratic operation of computers, telecommunication, monitors, electronic test equipment etc.
• No Resonance with power factor correction capacitors.
RI-11 Frame RI-12 Frame RI-22 Frame
RI-24 Frame
1 x module
RI-10 Frame RI-20 Frame
External batt. 1 x module 40 x 7/9Ah batt. 1 x module 80 x 7/9Ah batt. 2 x module External batt. 2 x module 80 x 7/9Ah batt.
2 x module
160 x 7/9Ah batt.
10kVA or 20kVA modules may be used in
RI-40 Frame
4 x module
External batt.
each configuration but in a multi-module
configuration both modules must be of equal rating.

UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013 2-3
2: General Description
2.4.2 Flexible battery management
This equipment employs a flexible battery management which avoids premature deterioration of battery life
by advanced management of battery charging and preventive failure diagnostics.
The major benefits are:
• AC-ripple free battery charging due to a dc-dc charger separated from the rectifier and inverter.
• Wide range of number of 12V battery blocks; depending autonomy times.
• UPS's wide input voltage operating window extends the battery life due to fewer discharge cycles.
• Battery discharge protection caused by load jumps.
• Proactive battery protection from false manipulations and inadequate charging voltages.
• Proactive battery failure detection thanks to Advanced Battery Diagnosis (ABD) - algorithm.
• User selectable battery tests.
• Optional temperature-compensated charging to enhance battery life.
2.4.3 Decentralized Parallel Architecture (DPA)
The PowerWAVE 8000-RI DPA system features DPA paralleling technology that provides n+x redundancy
without introducing a single-point-of-failure. The modules utilizing the DPA technology are completely
autonomous be means of individual power units, bypasses, CPUs, control panels and separate battery
configuration.
2.5 Warranty
The PowerWAVE 8000-RI DPA is supplied with a limited warranty that the UPS and its component parts are
free from defects in materials and workmanship for a period of one year from the date of original
commissioning or fifteen months from the date of original delivery, whichever is the sooner. This warranty is
the only warranty given and no other warranty, express or implied, is provided.
This warranty is invalidated if the UPS is put into use without having been commissioned by a fully trained
and authorised person. This warranty does not apply to any losses or damages caused by misuse, abuse,
negligence, neglect, unauthorised repair or modification, incorrect installation, inappropriate environment,
accident, act of God or inappropriate application.
If the UPS fails to conform to the above within the warranty period then Uninterruptible Power Supplies Ltd
will, at its sole option, repair or replace the UPS. All repaired or replaced parts will remain the property of
Uninterruptible Power Supplies Ltd.
As a general policy, Uninterruptible Power Supplies Ltd does not recommend the use of any of its products in
life support applications where failure or malfunction of the product can be reasonably expected to cause
failure of the life support device or to significantly affect it’s safety or effectiveness. Uninterruptible Power
Supplies Ltd does not recommend the use of any of its products in direct patient care. Uninterruptible Power
Supplies Ltd will not knowingly sell its products for use in such applications unless it receives in writing
assurances satisfactory to Uninterruptible Power Supplies Ltd that the risks of injury or damage have been
minimized, the customer assumes all such risks and the liability of Uninterruptible Power Supplies Ltd is
adequately protected under the circumstances
CAUTION: The UPS may contain batteries which must be re-charged for a minimum of 24
hours every six months to prevent deep-discharging (at 20°C). Batteries that have been, for
whatever reason, deep-discharged are not covered by the warranty.

2: General Description
2-4 UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013
2.6 Extended Warranty
The Standard Warranty may be enhanced by protecting the UPS with an Extended Warranty Agreement
(maintenance contract).
An Extended Warranty Agreement enhances the standard warranty by providing the following:
• Regular preventative maintenance inspections.
• Guaranteed speed of response to operational problems.
• 24 hour telephone support.
• Fully comprehensive cover (EXCLUDING BATTERIES & CAPACITORS).
• Contact the Service Support Hotline on 0800 731 3269 for further details.
2.7 Additional Service/Maintenance Support
In addition to providing support for the PowerWAVE 8000-RI DPA, Uninterruptible Power Supplies Ltd are
able to provide maintenance and support on a wide range of different UPS products.
If you are interested in an extended warranty for your PowerWAVE 8000-RI DPA, or any other UPS you may
have, please complete the enquiry form shown opposite and return or FAX to:
Uninterruptible Power Supplies Ltd.
Woodgate
Bartley Wood Business Park
Hook
Hampshire
RG27 9XA
Tel: [phone]
0800 731 3269 (24 Hr.)
Fax: [phone]
Email: [e-mail]

UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013 2-5
2: General Description
Thank you for your enquiry, which will receive our prompt attention.
If you need to contact us immediately call free on,
Freefone 0800 731 3269
or E-mail us on servi[email protected]
www.upspower.co.uk
Uninterruptible Power Supplies Ltd.
Woodgate
Bartley Wood Business Park
Hook
Hampshire
RG27 9XA
Tel: [phone]
Name: ............................................................................................
Job Title: ............................................................................................
Company: ............................................................................................
Address: ............................................................................................
............................................................................................
............................................................................................
............................................................................................
Post Code ............................................................................................
Tel. ............................................................................................
Fax. ............................................................................................
E-mail ............................................................................................
Please contact me to discuss:
Extended Warranty options for my PowerWAVE 8000-RI DPA UPS
Extended warranty options for my UPS System as below:
Manufacturer:...................................................................
Model Nº:..........................................................................
Rating kVA:.......................................................................
Replacement Batteries......................................................................
Other ..................................................................(please specify)
Fax to: 01256 386701 www.upspower.co.uk

2: General Description
2-6 UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013

UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013 3-1
3Installation
3.1 Introduction
This chapter contains all the information necessary for the correct unpacking, positioning, cabling and
installation of the PowerWAVE 8000-RI DPA.
3.2 Receipt of the UPS
The UPS and accessories are delivered on a specifically designed pallet that is easy to move with a forklift or
a pallet jack.
The packing container protects the UPS from mechanical and environmental damage. This protection is
further increased by wrapping the PowerWAVE 8000-RI DPA UPS with a plastic sheet.
Upon receiving the UPS, carefully examine the packing container and the UPS for any sign of physical
damage. The outside 'Tip&Tel' (“FRAGILE” and “ARROW”) indicator should be intact if the equipment has
been transported in an upright position. In case of rupture (or if they are suspect) immediately inform the
carrier and Uninterruptible Power Supplies Ltd
Ensure that the received UPS corresponds to the description indicated in the delivery note.
3.2.1 Site transportation
If you transport the UPS equipment after it has been off-loaded (for example, for storage or moving to a
different installation location) please read the following precautions.
WARNING: All the operations described in this section must be performed by authorised
electricians or suitably qualified personnel.
Uninterruptible Power Supplies Ltd. will take no responsibility for any personal or material
damage caused by incorrect cabling or operations, or activities which are not carried out in
strict accordance with the instructions contained in this manual.
CAUTION: When off loading the UPS always keep it in an upright position.
Do not drop the equipment.
Do not stack the pallets due to the high-energy batteries involved and the heavy weight.
CAUTION: Visible transport damages must be notified to the carrier immediately after receipt!
Other claims for shipping damage must also be filed immediately and the carrier must be
informed within 7 days of receipt of the equipment.
Packing materials should be stored for further investigation.
CAUTION: Transport:
To avoid the UPS cabinets and/or battery cabinet falling over, use the shipping brackets on the
rear and front to secure the cabinets.
– Do not tilt the cabinets more than 10° from vertical.
CAUTION: Potential dangers:
– If the cabinet has been tilted it might damage the equipment and it should not therefore be
connected to the mains electricity supply.
– The weight of the UPS system could cause serious injuries to persons or anything in the
surrounding area.

3: Installation
3-2 UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013
3.3 Unpacking
If the packages are received in good order (i.e. the ‘tip & tell’ “FRAGILE” and “ARROW” indications on the
packing container are intact) then perform the following steps to unpack the UPS:
1. Cut the wrappers and remove the packing container by pulling it upwards.
2. If the equipment is shipped inside a wooden case, remove the screws at the base and sides of the case
then carefully remove the case from the equipment.
3. Remove the plastic sheeting covering the UPS.
4. Remove the UPS from the pallet.
5. Retain the packaging materials for future shipment of the UPS.
6. Examine the UPS for any sign of damage and notify your supplier immediately if any damage is
apparent.
7. Open the cabinet door and ensure that all the UPS modules are correctly (and securely) fitted in their
UPS module compartments. Ensure that a protection cover is correctly fitted to the front of any empty
UPS compartments.
3.3.1 Nameplate
The technical specifications of the PowerWAVE 8000-RI DPA are provided on the nameplate which is
situated at the front of the UPS.
Check that the details on the nameplate corresponds to the purchased material detailed on the delivery note.
3.4 Batteries
The standard batteries connected to the UPS are sealed, maintenance-free batteries which will be mounted
on shelves either within the UPS sub-rack or in an external battery cabinet. The battery will usually be
assembled and connected when the UPS is commissioned.
The working life of the Battery is greatly affected by the ambient temperature and will be optimum when
operated at a temperature of 20°C.
If the UPS is delivered without batteries, Uninterruptible Power Supplies Ltd is not responsible for any
damage or malfunctioning caused to the UPS by the incorrect storage, installation or connection of batteries
by third parties.
3.5 Storage
3.5.1 UPS Module
If you plan to store the UPS prior to use, it should be stored in a clean dry environment with a temperature
between +5°C to +40°C and RH of less than 90%. If the packing container is removed, you must protect the
UPS from dust.
CAUTION: Storage:
– The UPS should be stored in the original packing and shipping carton.
– The recommended storing temperature for the UPS system and batteries is between +5 °C
and +40°C.
– The UPS system and the battery sets must be protected from humidity
< 90% RF (non-condensing).
WARNING: The UPS system, the battery cabinet (option) and the batteries are heavy and
may tip during transportation causing serious injury if the unpacking instructions are not
followed closely.

UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013 3-3
3: Installation
3.5.2 Battery
The UPS utilizes sealed, maintenance-free batteries, whose storage capability depends on ambient
temperature. It is therefore important not to store the UPS for longer than 6 months at 20°C, 3 months at
30°C and 2 months at 35°C storage temperature without a battery recharge. For longer term storage make
sure that the battery is fully recharged every 6 months @20°C.
3.6 Positioning
3.6.1 Planning the installation
A certain amount of pre-planning will help ensure smooth, trouble-free equipment installation. The following
guidelines should be taken into account when planning a suitable UPS location and environment.
1. The equipment must be installed and transported in a upright position.
2. The floor at the installed location and en-route from the off-loading point must be able to safely take the
weight of the UPS and battery equipment plus fork lift during transit.
3. The UPS requires space at the bottom (front and back) to enable cooling airflow. Suitable ventilation
airflow must be provided (See Figure 3.1).
4. All parts of the UPS required for maintenance, service and user operation are accessible from the front
and rear, making it a service-friendly and maintenance-friendly. Reserve a minimum of 900mm space at
the rear and 1000mm at the front of the UPS cabinet.
5. An ambient temperature of 20°C is recommended to achieve a long battery life. The cooling air entering
the UPS must not exceed +40°C.
6. Avoid high ambient temperature, moisture and humidity. The floor material should be non-flammable and
strong enough to support the heavy load.
7. In summary, the UPS should be located where:
a) Humidity (< 90% non-condensing) and temperature (+15°C to +25°C) are within prescribed limits.
b) Fire protection standards are respected.
c) Cabling can be performed easily.
d) Minimum 1000mm front accessibility is available for service or periodic maintenance. There should
also be a minimum 900mm clearance at the rear to enable access to the power connections.
e) The air conditioning system has a sufficient amount of air cooling to keep the maximum room
temperature rise at a desired level and the required air cooling flow is available.
f) No dust or corrosive/explosive gases are present.
g) The location is vibration free.
h) If the UPS will be installed in bayed enclosures, partition walls have to be installed.
CAUTION: Sealed batteries must never be stored in a discharged or partially discharged state.
Extreme temperature, under-charge and overcharge and over-discharge will destroy batteries!
Key Point: Note the following:
• Charge the battery both before and after storing.
• Always store the batteries in a dry, clean, cool environment in their original packaging.
• If the packaging is removed protect the batteries from dust and humidity.

3: Installation
3-4 UPS338-01-00 PowerWAVE 8000-RI DPA User Manual Dated 5 April 2013
Figure 3.1 UPS Space Recommendations
3.6.2 Heat Dissipation With Non-linear Load (per module)
3.7 Rack Assembly
Usually the racks used to house this equipment come fully assembled and ready for the modules to be
inserted. However, if this is not the case then the rack system must be assembled as illustrated in Figures 3.2
to 3.9.
UPS Cabinet
RI-10 RI-11 R1-12 RI-20 RI-22 RI-24 RI-40
Dimensions
(W x H x D) mm
448x310x735 448x487x735 448x665x735 448x440x735 448x798x735 448x1153x735 448x798x735
Rack Height 7HU 11HU 15HU 10HU 18HU 26HU 18HU
Service Accessibility Front and rear accessibility required for service and maintenance
Cabling Accessibility Min. 900 mm rear access required for connecting power cables
Operator controls Accessible from the front
10kW UPS Module 20kW UPS Module
Heat dissipation with 100% non-linear load.
Per module (EIN 62040-1-1:2003
W 550 1100
Heat dissipation with 100% non-linear load.
Per module (EIN 62040-1-1:2003)
BTU/h 1887 3754
Airflow (25° - 30°C) with non-linear load.
Per module (EIN 62040-1-1:2003)
m³/h 150 150
Dissipation at no load W 120 150
UPS
X
Y
X
Y
900 mm
1000 mm
Access Space
UPS
X
Y
Battery