Union Draisine KLV12 User manual

Draisine KLV12 H0 gauge
Manual
From 1953 the DB procured various types
of trolleys for railway service purposes,
including the types Klv 11 and Klv 12, of
which around 800 were produced by various
suppliers by 1963.
The simple purpose vehicles were inexpen-
sive. An air-cooled Volkswagen industrial
engine with a displacement of 1.2 liters and
28 hp served as the drive. Top speed 70 km /
h, total weight approx. 2,250 kg.
Maßstabsgetreues Modell für erwachsene
Sammler. Empfohlen für Sammler ab 14
Jahren. Aufgrund maßstabs- und
vorbildgerechter Umsetzung bzw. funk-
tionsbedingter Gestaltung sind Spitzen,
Kanten und Kleinteile enthalten.
Verschluckungsgefahr. Bitte bewahren Sie
die Verpackung für zukünftig benötigte
Informationen auf.
Detailed scale model for adult collectors.
Recommended for collectors aged 14 years
or older. Product could contain functional
sharp edges and small parts which can
present a choking hazard.
Please handle with care. Please retain
packaging for future reference.
GENERAL INFORMATION
Do not expose the model to intense solar
radiation or other strongly warming light
sources. Strong UV radiation changes or
ages paintwork. High temperatures can de-
form the plastic parts and bleach the paint.
The statutory regulation applies to any
warranty claims, please contact the seller of
the model. Please keep the proof of purchase
as a basis for the warranty claim.
Modellbahn Union GmbH
Gutenbergstr. 3a
D-59174 Kamen
email: [email protected]
Information on the Modellbahn Union range
can be found at info.modellbahnunion.com
ACHTUNG:
Maßstabsgetreues Modell für erwachsene
Sammler ab 14 Jahren.
Detailed scale model for adult collectors.
Recommened for collectors aged 14 years or older.
EN1.2/2021
GENERAL INFORMATION
The recommended minimum drivable radius
is 360mm.
The model has a 6-pin interface according to
NEM 651 for the
Digital operation. The interface connector is
equipped with buffer memories for analog
operation.
Important note: The model is equipped
with capacitors on the interface connector
for analog operation. Please do not change
direction abruptly, but bring the vehicle
to a standstill before changing direction.
Otherwise you risk damaging the drive and
capacitors.
For better contact security the model is not
equipped with friction tires.
The model is operated in analog mode with a
maximum of 12V direct current and is
Compatible with all common H0 gauge
direct current rail systems.
14+

SERVICE INSTALLATION OF A DIGITAL DECODER INSTALLATION OF A DIGITAL DECODER
A dummy plug is plugged into the 6-pin
interface for analog operation at the factory.
The dummy plug is connected to capacitors
(please also note the information below),
which are not required for digital operation.
You can easily pull off the dummy plug from
the side with needle-nose pliers.
The contact points for the decoder are thus
exposed. You can now plug in the decoder.
Pay attention to the correct installation
position. Information on this can be found
in the instructions for the decoder. When
installing the housing later, make sure that it
is in the correct position and that no cables
etc. are pinched.
Important note: set the CV5 for the maxi-
mum speed to a maximum of 40 or lower.
Otherwise you risk overloading and overhe-
ating the motor, which is designed for 5V!
Important note: The model is equipped
with capacitors on the interface connector
for analog operation. Please do not change
direction abruptly, but bring the vehicle
to a standstill before changing direction.
Otherwise you risk damaging the drive and
capacitors!
To install a digital decoder, the upper part of
the housing must be lifted off.
The separating edge is located below the
window; the component can be easily pulled
off with light pressure on the side on the
upper part. We recommend decoders from
Doehler & Hass or Zimo. Other decoders
may have too high a current consumption.
For safe storage of the individual parts and
for further work on the model, we recom-
mend the Modellbahn Union locomotive bed
MU-H0-A00500.
To ensure proper power consumption, both
your tracks and the wheels of the draisine
should be kept free of dust and dirt. The
wheels of the draisine can be used with the
usual
Cleaning uids.
We recommend AC13 Track Magic from
Deluxe Materials.
When using the model for the rst time,
allow it to run in for approx. 20 minutes in
each direction at medium speed.
After operating times of approx. 10 hours,
the gear wheels must be lightly greased from
the outside.
To grease the bogie gears, smear some model
railway grease on the visible gears of the
axles. Do not use oil! The grease is distribut-
ed in the drive mechanism.