Unior 1693 User manual

cvbcccvb
District Court of Celje, File No. 1/00248/00 • Share capital: 23.688.983, 48 EUR • Identification number: 5042437 •
V. A. T. Number: SI7246172 • Bank account No. SI56 0600 0002 5482 781 at Banka Celje d. d. • SWIFT SBCESI 2X •
Chairman of the Supervisory Board: Matej Golob Matzele.
1693 Fix-it-yourself bike stand
Instruction manual
Usage
1693E Fix-it-yourself bike stand is simple to use and compatible with all types and models of bicycles. We just simple
raise a bike, drive the seat post between the brackets of the stand and release the bike suspended freely. Service tools
are fastened to the stand with plasticized steel braided cables long enough to reach all parts of the bike. After the
service intervention has been completed, we raise the bike again, take it off the stand brackets and put it on the
ground. We check the tire pressure and cycle away satisfied.
Positioning
Fix-it-yourself bike stand is not free-standing. Stand has to be fastened on bedrock. The base of the stand has got four
holes which enable fastening on a concrete or any other hard surface with larger bolts. With safety precautions in
mind we advise against the use of stand without fastening to the ground.
Maintenance
Due to exposure to various weather conditions some parts of the stand (Tools + Pump) require constant maintenance.
Tools: We recommend oiling tools with Dry Lube (PTFE) at least once a month, if necessary, several times a month. In
winter we recommend Wet Lube once a week.
Pump: We recommend lubricating Handle stick with Dry Lube or PTFE spray 1-2 times a month. In winter repeat the
process several times a month. Rubber seals wear out over time and must be replaced after some time.
Warranty
3 years anti corrosion warranty on all galvanized and powder coated parts of the stand. Warranty does not apply if
corrosion is caused by physical damage, also excluded are damages due to any form of vandalism.
Tools are treated under standard Unior warranty. Due to tools being exposed to different elements, corrosion on tools
cannot be covered by Unior warranty. To ensure the longevity of the tools, please follow regular maintenance
requirements. See paragraph above.
SKS Pumps information:
https://www.sks-germany.com/en/products/airworx-10-0-silver/
Warning: both tools and pump are opened for public use and therefore used more than they would under standard
circumstances. Warranty does not apply for product wear. All maintenance is done by the owner of the stand, also all
the cost related to maintenance and tool replacements is covered by the owner.

2
Spare products
Code
Art
Dim.
Name
611918
250/1
150
Adjustable wrench
610986
220/3MH
2.5-10/7 MB
Set of hexagon wrenches in metal folding holder
611704
615TBI
PH 2X100
Crosstip (PH) screwdriver TBI
612816
605TBI
1.0X5.5X100
Flat screwdriver TBI
615120
1612PB
Set of cone wrenches
623387
1657/2A
Set of two metal tire levers
625519
1693E.SKS10S
SKS Airworks 10.0 Silver floor pump
625520
1693E.SKS10001
SKS Rubber washer for Airworks 10.0, 35mm
625521
1693E.SKS10002
SKS Hose connection with Multivalve head, Airworks
625522
1693E.SKS10003
SKS Multivalve head for Airworks
625523
1693E.SKS10004
SKS Rubber seal for Multivalve head, Airoworks
625524
1693E.WIRE01
Tool wire, stainless steel, plastic coated 1,4m
625525
1693E.WIRECL
Aluminum wire clamp
625526
1693E.RUBB01
Protective rubber for Tool hole
625527
1693E.ENDCAP01
Outer plastic end cap for bike hanger
625528
1693E.ENDCAP02
Inner plastic end cap for bike hanger
625529
1693E.UVCOVER1
UV rubber cover for bike hanger, transparent, 14cm
625530
1693E.TOPCAP1
Plastic top cap, CNC made
625531
1693E.PCOVER1
Protection cover for pump, galvanized, painted
Pump
Stand comes with high quality floor pump of a renowned German manufacturer SKS, model Airworx 10.0 floor pump.
Pumps are equipped with a gauge and are compatible with all valves and are very easy to use.
Pump information:
https://www.sks-germany.com/en/products/airworx-10-0-silver/
Instruction manual:
http://www.sks-germany.com/inhalte/uploads/2015/11/AB_bedienungsanleitung_AIRWORX_10.0_en.pdf
Spare parts:
http://www.sks-germany.com/inhalte/uploads/2015/08/AB_ersatzteile_AIRWORX_10.0.pdf

3
Pump maintenance and replacement
To replace or maintain the pump, follow these steps:
1) With a drill, remove ten rivets –6 from the side, 4 from the bottom, to separate the pump frame from the
main frame. Use drill 4.2mm. (image 1)
2) Unscrew the bottom 4 screws to remove the metal plate under the pump (image 2)
3) Keeping the complete frame and pump upside down, pull the plastic part from the pump (image 3)
4) Remove the pump from the metal frame
5) Change the rubber washer or change the pump
6) Install the pump into the frame
7) Install the metal plate on the floor bottom with 4 screws (image 4)
8) Use a rivet gun and 10 new blind rivets to install the pump frame back on the stand main frame. Rivet
dimension 4 x 9mm. (image 5)
Image 1.

4
Image 2. Image 3.
Image 4. Image 5.