Unipoe PM5003GSN User manual

User Guide
用户手册
2GE(PoE)+1GE以太网 PoE 交换机
2*10/100/1000Mbps+1GE PoE Switch

- 1 -
Package Contents
Check the following contents of your package:
 PoE Switch x 1
 User Guide x 1
 Power Cord x 1
 Accessories(Feet*4)
If any part is lost and damaged, please contact your local agent immediately.
Introduction
2+1 Gigabit Provides the seamless network connection. The PoE ports (Port2~3) can automatically detect and supply
power with those IEEE 802.3af/at/bt compliant Powered Devices (PD). The electrical power is transmitted along with data
in one single cable allowing you to expand your network where there are no power lines or outlets, where you wish to fix
devices such as AP, IP Cameras or IP Phones, etc.
It is easy to install and don’t need to configuration. With outstanding performance and quality, the 3-port
10/100/1000Mbps desktop PoE switch is an ideal choice for expanding your home or office network.
Hardware Description
Front Panel
The Front Panel of 2+1 Gigabit Consists of 3-Port 10/100/1000Mbps Ethernet RJ45 Ports. The LED indicators are also
located on the panel.
Intelligent display of PoE power supply
When using the PoE power supply to connect the PD equipment, The PoE lantern will check the PD equipment to
meet the power supply of 2 pairs of wires. the "2-2Pair,3-2pair" light will be green ,the 4 pairs of wires will supply power.
the "2-4Pair" light will be green

- 2 -
Through the panel on PoE Usage green lights, the user can understand the real-time status ，When the output power
reaches 25%, “25%”green LED lights, when the output power reaches 50%, "25% to 50%" green LED lights. When the
output power reaches 75%, "25% to 50%and 75%" green LED lights. When the output power is up to 90%, “25% to 50%
and 75% to 90% "will all light green.
LED indicator
LED
Color
Function
PWR
Green
Off: No Power supply.
Light: Indicates the switch has power.
DATA
Green
Orange
Off: No device is connected to the corresponding port.
Green: Indicates the link through that port is successfully
established at 1000Mbps.
Orange: Indicates the link through that port is successfully
established at 10/100Mbps.
Blink: Indicates that the Switch is actively sending or
receiving data over that port.
PoE
Green
Off: No PoE powered device (PD) connected.
Light: There is a PoE PD connected to be port, which
supply power successfully.
Blink: Indicates port abnormal power supply.
Rear Panel
The rear panel of 2+1 Gigabit indicates AC inlet power socket and Grounding column.

- 3 -
Installation the Switch
This part describes how to install your Ethernet Switch and make connections to it. Please follow the following instructions
in avoid of incorrect installation causing device damage and security threat.
Before cleaning the switch, unplug the power plug of the switch first. Do not clean the switch with wet cloth or liquid;
Do not place the switch near water or any damp area. Prevent water or moisture from entering the switch chassis;
Do not place the switch on an unstable case or desk. The switch might be damaged severely in case of a fall;
Ensure proper ventilation of the equipment room and keep the ventilation vents of the switch free of obstruction;
Make sure that the operating voltage is the same one labeled on the switch;
Do not open the chassis while the switch is operating or when electrical hazards are present to avoid electrical shocks.
Desktop Installation
Install the Switch on a desktop, Allow adequate space for ventilation between the device and the objects around it. The
bottom of the switch is shown in figure：
Wall-mounted installation
In the first two fixed screw on the wall as shown in the figure below
Aim at the two fixed hole switches, and the machine smoothly on the screw

- 4 -
Turn on the switch
The PoE switch can be used with AC power supply. Powering on the switch, it will automatically initialize and its LED
indicators will respond as follows:
Firstly, the Power LED indicator will light up.
Then, the data LED indicators will flash momentarily for one second, which represents a resetting of the system.
Specifications
Model
2+1 Gigabit
Standard
IEEE802.3, IEEE802.3u, IEEE802.3az, IEEE802.3x, IEEE802.3af,
IEEE802.3at, IEEE802.3bt
Network Media(Cable)
10BASE-T: UTP category 3,4,5 cable (≤100m)
100BASE-TX: UTP category 5 cable (≤100m)
1000BASE-T: UTP category 5e cable (≤100m)
MAC Address Table
2K, Auto-learning, Auto-aging
Transfer mode
Store-and-Forward
Frame Forward Rate
10Base-T: 14881pps/Port
100Base-TX: 148810pps/Port
1000Base-T/X: 1488095pps/Port
Switching Capacity
6Gbps
Dimensions (L*W*H)
168*93*32mm
Fan
Fanless
Power input
AC 100V-240V 50/60Hz
PoE Port
Port2~3
PoE Power on RJ45
4 Pair
Data Pairs 1/2(+),3/6(-)
Spare Pairs 4/5(+),7/8(-)
PoE Output
60W+30W(Max)
Temperature
Operating Temperature: 0°C ~ 40 °C (32 °F ~104°F )
Storage Temperature: -40 °C ~ 70 °C (-40 °F ~158°F )
Humidity
Operating Humidity: 10% ~ 90% non-condensing
Storage Humidity: 5% ~ 90% non-condensing

- 5 -
包装清单
小心打开包装盒，包装盒内应有以下物件：
PoE 交换机 . . . . . .. . . . . . . . . . . . . . . . . . . 一台
用户手册. . . . . . . . . . . . . . . . . . . . . .. . . . . .一本
电源线. . . . . . . . . . . . . . . .. . . . . . . . . . . . . .一根
安装附件（脚垫*4）
如果发现有物件损坏或者短缺的情况，请及时和当地经销商联系。
产品简介
2+1 千兆提供 2 个10/100/1000Mbps RJ45 端口跟 1个10/100/1000Mbps 上联端口， 每个 RJ45 端口均支持
MDI/MDIX 自动翻转和线速转发功能。2-3 端口支持 PoE 供电，PoE 端口能自动检测 PD 设备，并为符合 IEEE
802.3at/af/bt 标准的 PD 设备供电。在为一些基于 IP 的终端（如 IP 电话机、 无线局域网接入点 AP、网络摄像
机等） 传输数据信号的同时，还能为此类设备提供电力的技术。它不仅能保证网络的正常运作和避免高压布线的
危险，还能最大限度地降低成本。
使用简单方便，无需配置，即插即用，可灵活扩展家庭、办公室网络而不受电力线布局限制，电源可自由选配。
外观描述
前面板
前面板由 3 个10/100/1000Mbps 自适应 RJ45 端口，相关的指示灯组成，如下图所示：

- 6 -
PoE 电源智能显示
当使用 PoE 电源连接 PD 设备时，PoE 灯将检查 PD 设备，满足 2对电线的供电。“2-2Pair,3-2pair”灯将是绿色的，4对电线供电。
“2 - 4pair”灯将是绿色的
通过面板上的 PoE 使用功率指示灯，用户可以实时了解该机器的 PoE 输出状态，当输出功率达到 25%时，“25%”的 LED 灯亮绿色，
当输出功率达到 50%时，“25%到50%”的 LED 灯亮绿色。当输出功率达到 75%时，“25%，50%”和“75%”的 LED 灯都亮绿
色。当输出功率达到 90%时，“25%到50%，75%到90%”将全部亮绿色。
LED 指示灯
指示灯
颜色
描述
PWR
绿色
灭：交换机未通电。
常亮: 交换机已通电。
DATA
绿色
橙色
灭：没有连接网络设备。
绿色: 连接到 1000Mbps 设备。
橙色：连接到 10/100Mbps 设备
闪烁: 与相连的设备有数据传输。
PoE
绿色
灭： 端口未给对端设备供电。
常亮: 有受电设备与之连通，并正常供电。
闪烁：端口为对端设备供电异常。
后面板
后面板示意图: AC 电源插孔连接电源线，防雷接地柱。

- 7 -
安装设备
注意事项
为避免使用不当造成设备损坏及对人身的伤害，请遵从以下的注意事项：
在清洁交换机前，应先将交换机电源插头拔出。不要用湿润的布料擦拭交换机，不可用液体清洗交换机；
请不要将交换机放在水边或潮湿的地方，并防止水或湿气进入交换机机壳；
请不要将交换机放在不稳定的箱子或桌子上，万一跌落，会对交换机造成严重损害；
应保持室内通风良好并保持交换机通气孔畅通；
交换机要在正确的电压下才能正常工作，请确认工作电压同交换机所标示的电压相符；
为减少受电击的危险，在交换机工作时不要打开外壳，即使在不带电的情况下，也不要随意打开交换机机壳。
桌面安装
将交换机的底部朝上放置于足够大且稳定的桌面上；交换机底部如图：
小心将交换机正置，放在工作台上。
壁挂式安装
请按照以下步骤安装 PoE 交换机：
在墙壁上先固定两颗螺钉 如下图所示对准交换机的两个固定孔，把机器平稳的挂在螺钉上

- 8 -
通电
接上电源线，插上插头，接通电源。开机以后，交换机将自动进行初始化，所有的端口指示灯全亮后熄灭，表示系
统复位成功。电源 LED 指示灯一直常亮。
注意：上电前请确认电压是否正确，否则将损坏设备。（电源输入范围 100-240V AC 50/60Hz）。
技术规格
产品名
2+1 千兆 PoE 交换机
标准
IEEE802.3, IEEE802.3u,IEEE802.3az, IEEE802.3x, IEEE802.3af, IEEE802.3at
IEEE802.3bt
网络介质（线缆）
10BASE-T: Cat 3,4,5 非屏蔽类双绞线(≤100m)
100BASE-TX: Cat 5 及以上非屏蔽类双绞线(≤100m)
1000BASE-T：Cat 5 及以上非屏蔽类双绞线(≤100m)
MAC 地址表
2K, 自动学习，自动更新
传输模式
存储转发
包转发速率
10Base-T:14881pps/端口
100Base-TX: 148810pps/端口
100Base-T/X: 1488095pps/端口
背板带宽
6Gbps
尺寸(长*宽*高)
160*93*32mm
风扇
无风扇
电源输入
AC 100V-240V 50/60Hz
PoE 端口
Port 2~3
PoE 供电线对
四对线供电
正极 1/2 负极 3/6
正极 4/5 负极 7/8
PoE 端口输出
60W+30W（Max）
工作温度
0°C ~ 40 °C
存储温度
-40 °C ~ 70 °C
工作湿度
10% ~ 90% 无凝结
存储湿度
5% ~ 90% 无凝结