Unipower Gravitas X100 Installation instructions

INSTALLATION & OPERATING MANUAL
X100 SERIES
DC POWER POWER SYSTEM
www.unipowerco.com
Manual No. X100-5a © 2014 UNIPOWER LLC
All Rights Reserved
x100-man-Rev5a-0214.indd
NORTHAMERICA • 3900 Coral Ridge Drive, Coral Springs, Florida 33065, USA • Tel: [phone] • Fax: [phone] • [email protected]
EUROPE • Parkland Business Centre, Chartwell Road, Lancing BN15 8UE, ENGLAND • Tel: [phone] • Fax: [phone] • [email protected]

Page 2
X100 SERIES
INSTALLATION & OPERATING MANUAL
Manual No. x100-5a x100-man-Rev5a-0214.indd
CONTENTS
1.0 INTRODUCTION.................................................................................................................4
2.0 FEATURES & OPTIONS......................................................................................................5
3.0 SAFETY WARNINGS ..........................................................................................................5
4.0 WARRANTY (summary) ......................................................................................................6
5.0 UNPACKING AND INSPECTION ......................................................................................6
6.0 GENERAL SPECIFICATIONS ............................................................................................7
7.0 FRONT PANEL DESCRIPTION..........................................................................................9
8.0 REAR PANEL DESCRIPTION ..........................................................................................10
9.0 CURRENT METER & LED INDICATORS.......................................................................12
10.0 MAKING CONNECTIONS TO THE X100.......................................................................13
11.0 INSTALLATION.................................................................................................................16
12.0 USING THE CONTROLLER WEB BROWSER INTERFACE........................................20
Appendix 1 – SNMP MIB Information .........................................................................................43
Appendix 2 – Revision History......................................................................................................47

Page 3
X100 SERIES
INSTALLATION & OPERATING MANUAL
Manual No. x100-5a x100-man-Rev5a-0214.indd
FIGURES
Figure 1 X100 Compact Integrated DC Power System ...............................................................4
Figure 2 Front Panels with Bezel Removed.................................................................................9
Figure 3a Rear Panel – Options A& B........................................................................................10
Figure 3b Rear Panel – Option C .................................................................................................10
Figure 4 Current Meter and LED Indicators (showing MAJ & FUSE alarms) .........................12
Figure 5 Controller Status WEB Page (typical).........................................................................24
Figure 6 Rectier Status WEB Page (typical)............................................................................25
Figure 7 Controller Factory Calibration WEB Page (typical)....................................................27
Figure 8 Controller Site Installation WEB Page (typical)..........................................................28
Figure 9 Alarm Conguration WEB Page (typical)...................................................................32
Figure 10 Controller Network Settings (typical)..........................................................................35
Figure 11 ControllerAlarm Log WEB Page (typical)..................................................................38
Figure 12 Controller Control Panel WEB Page (typical).............................................................39
Figure 13 Controller System Settings WEB Page (typical).........................................................40
Figure 14 SNMP Conguration WEB Page (typical) ..................................................................41
Figure 15 Controller Help WEB Page (typical)...........................................................................42
Figure 16 About UNIPOWER Telecom WEB Page (typical)......................................................42
TABLES
Table 1 Temp. Probe, Aux. Input & Alarm Relay Connector Pin-Out........................................14
Table 2 Ethernet Connector Pin-Out...........................................................................................15
Table 3 Input Current Ratings.....................................................................................................16
Table 4 Rectier I²C Addressing ................................................................................................25

Page 4
X100 SERIES
INSTALLATION & OPERATING MANUAL
Manual No. x100-5a x100-man-Rev5a-0214.indd
1.0 INTRODUCTION
Gravitas X100 is an ultra-compact, integrated, DC power system. It consists of up to
three high power-density, hot-swap rectier modules which can produce up to 66 amperes
at -54.4VDC, 99 amperes at +27.2VDC or 100 amperes at +13.6VDC. In 2+1 redundant
operation the output current is up to 44 amperes at -54.4VDC, 66 amperes at +27.2VDC or
100 amperes at +13.6VDC.
The system has a congurable DC distribution panel with options of up to 10 load circuits
protected either by GMT fuses or circuit breakers. Two battery breakers and a low-voltage
battery disconnect are included as standard. The system also has a temperature probe for
temperature compensated output from the rectiers and an optional second probe can be
used to monitor external temperature.
The intelligent control and supervisory unit communicates directly with the rectiers to
monitor and control their function. The system can be controlled by software from a remote
PC via the Ethernet LAN port, using an on-board WEB server which can be accessed by
any standard Java enabled WEB browser.
The complete Gravitas X100 isonly 2RUhigh (3.47inchesor 88.1mm)and is easilyinstalled
by a qualied technician. All connections are at the rear to terminal blocks. The unit may
be mounted in a 19 or 23 inch rack.
.
Figure 1 - X100 Compact Integrated DC Power System

Page 5
X100 SERIES
INSTALLATION & OPERATING MANUAL
Manual No. x100-5a x100-man-Rev5a-0214.indd
2.0 FEATURES & OPTIONS
2.1 Standard Features
2RU High System Unit
Remote Control & Monitoring via TPC/IP Ethernet LAN
Fully Integrated System
Up to 66A at -54.4VDC
Up to 99A at +27.2VDC
Up to 100A at +13.6VDC
Wide Range AC Input
Up to 10 DC Load Circuits
Circuit Breakers or GMT Fuses
Quick and Easy Installation
Universal 19/23-Inch Mounting Brackets
SNMP reporting and Error Trapping
2.2 Options & Accessories
Additional Probe for External Temperature Measurement (‘T’ Option)
Various AC Line cords and DC cable sets
3.0 SAFETY WARNINGS
3.1 The X100 Compact DC Power System operates at voltages that could potentially
be hazardous. Furthermore, inadvertent short circuiting of the system battery and/
or rectier by misconnection or other error could be harmful. This product should
be handled, tested and installed only by qualied technical persons who are trained
in the use of power systems and are well aware of the hazards involved.
3.2 When operating the X100 the chassis ground terminal must be connected to the
system frame ground or other proper safety ground for the protection of personnel.
3.3 All connections to the X100 should be carefully checked for errors before applying
power to it.
3.4 This equipment is intended only for installation in a “RESTRICTED ACCESS
LOCATION”

Page 6
X100 SERIES
INSTALLATION & OPERATING MANUAL
Manual No. x100-5a x100-man-Rev5a-0214.indd
4.0 WARRANTY (summary)
X100 Series DC power systems are warranted for two (2) years from date of shipment
against defects in material and workmanship. This warranty does not extend to products
which have been opened, altered or repaired by persons other than persons authorized by
the manufacturer or to products which become defective due to acts of God, negligence or
the failure of customer to fully follow instructions with respect to installation, application
or maintenance.
For a complete text of UNIPOWER’s warranty conditions please request a copy from your
local Sales Ofce.
5.0 UNPACKING AND INSPECTION
5.1 This X100 DC power system was carefully tested, inspected and packaged for
shipment from our factory. Upon receipt the unit should be carefully unpacked and
inspected for any damage in shipment.
5.2 If there is evidence of damage, do not attempt to install the unit. The freight
carrier should be notied immediately and a claim for the cost of the X100 should
be led with the carrier for direct reimbursement. Be sure to include the model and
serial number of the damaged unit in all correspondence with the freight carrier.
Also save the shipping carton and packing material as evidence of damage for the
freight carrier’s inspection.
5.3 UNIPOWER will cooperate fully in case of any shipping damage investigation.
5.4 Always save the packing materials for later use in shipping the unit. Never ship the
system or the rectier modules without proper packing.

Page 7
X100 SERIES
INSTALLATION & OPERATING MANUAL
Manual No. x100-5a x100-man-Rev5a-0214.indd
6.0 GENERAL SPECIFICATIONS
6.1 Inputs
Supply Voltage: 85-264VAC Single Phase
Each rectier position is supplied via an individual
pair of screw terminals.
A 3-phase supply may be connected provided that the voltage presented to each
individual rectier position does not exceed 264VAC.
Supply Current: Max 17A input @ 85-264VAC per rectier input.
Battery Input: Direct connection to DC output bus or via protection
breakers.
Digital alarm inputs: Volts free contact input*
*Volts free contacts are internally pulled up to 5V with reference to rectier negative
sense, these lines should not be tied to anything other than volts free contacts or
oating opto-coupler outputs.
Temperature probes: Sensorwithoutput currentproportionalto temperature.
6.2 Outputs
Breaker Distribution: Up to 8 circuits, maximum 50A per circuit.
Fuse Distribution: Up to 10 circuits, maximum 12A per circuit.
Alarm Relay Contacts: Form C, 1A max at 30VDC.
Ethernet: 10/100 Base T
6.3 Protection
Supply Input: Each rectier is individual fused internally.
Battery: 100A Magnetic Circuit Breaker.
Output Distribution: According to installed circuit breakers or fuses.
Bulk DC Bus: Rectier Current Limiting / Battery Breaker.

Page 8
X100 SERIES
INSTALLATION & OPERATING MANUAL
Manual No. x100-5a x100-man-Rev5a-0214.indd
6.4 Safety
The X100 system is compliant with UL60950-1, EN60950-1, CSA22.2-60950-1 and
all other derivatives of the core IEC60950-1 standard 2nd Edition when installed
correctly within a restricted access environment.
The X100 system is CE marked to indicate conformance to the European Union’s
Low Voltage and EMC Directives.
6.5 EMC
The X100 complies with the following Norms when correctly installed.
Conducted Emissions: EN55022, level A
Radiated Emissions: EN55022, level A
ESD: EN61000-4-2, level4,criterionA- 8kVcontact, 15kV
air.
Radiated Immunity: EN61000-4-3, level 3, criterion A - 10V/m.
Surges (power ports): EN61000-4-5, level 1, criterion A - 500V
6.6 Environmental
Operating Temperature: -40°C to 50°C
Storage Temperature: -40°C to 75°C
Humidity: 0% to 95% Non-Condensing
6.7 PhysicalSpecication
Case Material: Steel
Finish: Clear Passivated
Dimensions: 3.47H (88.1) x 17.2W(437) x 12.8D(325)
Rack Width: 19” or 23” using dual purpose kit supplied.
NOTE: Mid-mount is recommended when used in
free space.

Page 9
X100 SERIES
INSTALLATION & OPERATING MANUAL
Manual No. x100-5a x100-man-Rev5a-0214.indd
7.0 FRONT PANEL DESCRIPTION
OPTION A – MINIATURE CIRCUIT BREAKERS
BATTERY
BREAKERS DC DISTRIBUTION 1-8 CIRCUIT BREAKERS
LOAD
CURRENT
DISPLAY
16 LED
STATUS & ALARM
MATRIX
HOT-SWAP RECTIFIER MODULES
OPTION B – GMT FUSES
DC DISTRIBUTION
10 GMT FUSES
OPTION C – BULK FEED CIRCUIT BREAKERS
DC DISTRIBUTION
1-4 CIRCUIT BREAKERS
Figure 2 - Front Panels with Bezel Removed
7.1 From left to right there are 3 rectier slots. Each slot can accept one rectier from the
RADIAN Series rated up to 1200W output power. Only identical model rectiers of
appropriate output voltage maybe installedat thesame time. For example,a nominal
-48V system may contain between 1 and 3 model RPCP48/22-Z OR between 1 and
3 model RPCM48/15-Z but not a mixture of the two types.
7.2 Above rectiers is the distribution and display section. There are 3 types of DC
distribution depending on the option that has been specied.
7.2.1 Option A provides up to 8 DC load circuits with miniature circuit breaker
protection. Each circuit may be specied with a breaker of maximum rating
30A.
7.2.2 Option B provides a total of 10 DC load circuits with GMT fuse protection.
Each circuit can employ a maximum fuse rating of 12A.

Page 10
X100 SERIES
INSTALLATION & OPERATING MANUAL
Manual No. x100-5a x100-man-Rev5a-0214.indd
7.2.3 Option C provides up to 4 bulk DC load circuits with circuit breaker
protection. Each circuit may be specied with a breaker of maximum rating
50A.
7.3 To the right of the DC distribution section is a display section.
7.3.1 Current Meter – displays the total system load current.
7.3.2 16 LED Matrix – provides visual indication of a variety of status and alarm
condition. Full details can be found in section 9.
8.0 REAR PANEL DESCRIPTION
ETHERNET
J1
DC LOAD TERMINALS BATTERY TERMINALS
(2 STRINGS)
AC INPUTSRELAY ALARMS
TEMP. COMP.
AUX. INPUT
J2
RESERVED FOR
FACTORY USE
J3
Figure 3a - Rear Panel – Options A& B
ETHERNET
J1
DC LOAD TERMINALS BATTERY TERMINALS
(2 STRINGS)
AC INPUTSRELAY ALARMS
TEMP. COMP.
AUX. INPUT
J2
RESERVED FOR
FACTORY USE
J3
Figure 3b - Rear Panel – Option C
8.1 In the centre, viewed from the rear, is a bank of screw terminal block for the DC
load connections.
When options A or B have been specied one terminal pair is provided for feed and
return for each circuit installed; 1-8 for circuit breakers, 10 for GMT fuses.
When option C has been specied 4 pairs of bulk terminal blocks are tted to provide
one pair for feed and return for each circuit installed, from 1 to 4.
Note that the return (RTN) terminals are NOT internally connected to chassis
ground.
FEED (-Ve48, +Ve24, +Ve12)
RTN (+Ve48, -Ve24, -Ve12)
FEED (-Ve48, +Ve24, +Ve12)
RTN (+Ve48, -Ve24, -Ve12)