United Care B.V. Wendy 3 User manual

Introduction
Description
Operation
Maintenance
Annual Inspection
Problem Solving
Warranty

REF0717-2 1
Contents
1 Introduction
1.1 The Wendy hoist…………………………………………………….………………………………………………………………………..3
1.2 Points of attention………………………………………………….………………………………………………………………………..4
1.3 Technical data………………………………………………………….……………………………………………………………………….5
2 Description
2.1 Overview of the Wendy……………………………………………………………………………………..……………………………..6
2.2 Control box …………………………………………………………………………………………………….……..…….…………………..7
2.2.1 Emergency stop button
2.2.2 Electrical emergency lower control
2.2.3 Display
2.3 Handset ………………………………………………………………………………………………………………………….………………..8
2.4 Lifting motor …………………………………………………………………………………………………………………………………….9
2.5 Battery
2.5.1 Battery life
2.6 Battery charger …………………………………………………………………….………………………………………………………….10
2.6.1 Charging batteries
2.7 Chassis ………………………………………………………………………………………….………………………………………………….11
2.7.1 Adjusting the leg adjustment
2.8 Wheels
2.9 Cradle……………………………………………………………………………………………………………………………………………….12
2.10 Slings
2.10.1 Boning/Ribs ………………………………………………………………………………………………………………….13
2.10.2 Attachment to the Hoist
2.10.3 Types and dimensions
2.10.4 Table of standard slings………………………………………….……………………………………………………. 14
2.10.5 Washing instructions ……………………………………………….……………………………………………………15
3 Use
3.1 Introduction……………………………………………………………………………………………………………………………………….16
3.2 Attach the sling
3.2.1 Apply toileting sling
3.2.2 Apply the sling while seated
3.2.2 Fitting the sling from laying position………………………………………………………………………………..17
3.3 Hoisting ……………………………………………………………………………………………………………………………………………..18
3.3.1 Hoisting to the toilet
3.4 Driving ……………………………………………………………………………………………………………………………………………….19
3.4.1 Turning with the Hoist
3.5 Removing the user from the Hoist
4 Maintenance
4.1 Planning of maintenance…………………………………………………………………………………………………………………….20
4.1.1 Daily maintenance
4.1.2 Weekly maintenance
4.1.3 ½ Annual maintenance……………………………………………………………………………………………………..21
4.1.4 Annual inspection and maintenance
4.2 Finding and remedying malfunctions…………………………………………………………………………………………………..22
4.3 Removal of parts
4.4 Parts lists for the Wendy……………………………………………………………………………………………………………………..23
5 Appendix
5.1 Warranty provisions…………………………………………………………………………………………………………………………….28
5.2 About United Care
5.3 Contact
5.4 EC Declaration of conformity……………………………………………………………………………………………………………….29

2 REF0717-2
Preface
This Manual
The purpose of this manual is to allow care providers to operate the Wendy hoist and to perform simple
(preventive) maintenance.
This manual deals with the following aspects of working with the Wendy hoist:
•Description of the parts of the Wendy hoist
•Description of the operation of the Wendy hoist
•Step-by-step hoisting instructions
•Maintenance of the Wendy hoist
In addition to this manual, there is a Quick Reference on the hoist. This sheet contains a short description,
safety instructions and points for attention for operating the Wendy Hoist.
Symbols Used:
Attention point
High Voltage Warning
The manufacturer of the product
Read the manual before operating the hoist
The Wendy hoist meets the EMC standard 60601-1-2 and has the CE certificate.
The Wendy hoist complies with the European Medical Devices Directive, and has a
CE marking.
Contents of the package
Remove the packaging from the Wendy hoist and check if the parts below are present.
•The Wendy hoist
•One or two batteries
•A battery charger (with bracket and power cord)
• A sling (Optional)
•A manual
•Quick reference card (depends on the hoist)
•Logbook

REF0717-2 3
Introduction 1
1.1 The Wendy Hoist
The Wendy hoist is intended to provide a passive transfer for people in need of care. The user can be lifted
using the sling with the Wendy hoist. The user can be brought into a sitting or lying position to complete a
comfortable transfer from a chair to bed, for example.
The Wendy hoist can, among other things, be used for the following types of transfers:
• From and to chair, wheelchair.
• From and to the toilet.
• To and from shower-bath-toilet seat.
• From and to bed, stretcher.
• From and to the floor.
The Wendy hoist is a compact, manoeuvrable hoist with a large reach. It can lift people from the ground to a
high lifting height. Operating the hoist is very easy.
The hoist is available with an X-Shaped or an electrically adjustable/powered cradle. The X-Shaped Spreader
Bar is for slings with loops, the electric model is a four-point cradle for slings with clips.
The legs of the frame can be electrically adjusted in width for better positioning.
The expected service life, under normal use and under normal circumstances and apart from hoisting belts,
slings and batteries, is 10 years (100,000 transfers) for maintenance in accordance with regulations.

4 REF0717-2
Introduction 1
1.2 Points of attention
• The Wendy hoist is designed to be used in combination with a suitable sling, to lift and move users
and as such may only be used for this purpose. Any other purpose is not permitted.
• Operating the hoist is only permitted by demonstrably authorized persons.
• It is not permitted to lift a weight of more than the maximum permitted load with the Wendy hoist.
This is stated on the arm of the hoist.
• It is not permitted to lift anything else (such as a chair or wheelchair) together with the user.
• When hoisting, always check that there is sufficient space above the hoist. When passing through a
door frame, always check that there is sufficient space above the lifting arm.
• When approaching and moving the hoist, always check that the room where the transfer is taking
place is free of obstacles.
• Handle the hoist with care and ensure a clean and tidy working environment.
• The hoist must not be used on sloping surfaces with a slope of more than 5 degrees.
• Batteries should always be charged in a well-ventilated, dry room. Chargers must be connected in
accordance with the applicable installation regulations.
• Only use the Wendy hoist with a sling supplied by United Care, always contact United Care if you
intend to use a different type of sling.
• Attaching the clips of a sling to the cradle of the Wendy hoist must be done carefully, the incorrect
application of a clip can cause a person to fall and thus cause serious injury.
• The lift motor of the hoist is only intended for raising the lift arm, and thus lifting the user, and may
never be used as a support or handle.
• Pulling or pushing (also with the feet) on this motor can be dangerous.
• The Wendy hoist must be periodically inspected at least once a year.
• Service and maintenance on the hoist is only permitted by persons who are demonstrably authorized
to do so.
• Repairing and / or replacing parts of the hoist is only permitted by demonstrably authorized persons.
• Use only original parts supplied by United Care for service and repair.
• If deformations have occurred on the hoist due to incorrect use or transport, this may no longer be
used and must be returned to the supplier.

REF0717-2 5
Introduction 2
1.3 Technical data
Specifications of the Wendy hoist
Total weight 55 kg
Maximum lifting capacity 160/230 kg
Sound pressure 42dB (A)
Specifications of electrical parts
Lift motor 24Vdc 10A, IP65
10% duty cycle
Control box 24Vdc 10A max
IP65, EN60601-1
10% duty cycle
Handset HB3, IP65, 4 of 6 functions
Battery Pb 24Vdc, 2.9A, 74Wh
Li-ion 25.6Vdc, 3.3Ah, 84Wh
IP65, EN60601-1
Battery charger Primary 100-240Vac
50 / 60Hz, 400mA,
Fuse 1.25A 250V
Secondary 29.5Vdc, 19W max
IP65, EN60601-1

6 REF0717-2
Description 2
2.1 Overview of the Wendy Hoist
The following components are further detailed in their own section.
1
Control box
2.2
pg 7
2
Electric Emergency
Stop
2.2.2
pg 7
3
Handset
2.3
pg 8
4
Leg Adjustment
2.7
pg 11
5
Wheels
2.8
pg 11
6
Liftmotor
2.4
pg 9
7
Mechanical
Emergency Stop
2.4
pg 9
8
Battery
2.5
pg 9
9
Cradle
2.9
pg 12
10
Sling
2.10
pg 12
Lifting Arm
Leg
Spreader Bar
Hook clip
Frame
Caster Wheel
Caster Wheel with Brake
Push Handle
Powered
Spreader Bar
Motor

REF0717-2 7
Description 2
2.2 Control box
The control (control box) of the Wendy hoist is located between the frame on
the operating side of the lift. The hand control and the motors are plugged in
here. The control box provides the control, emergency stop and over-current
protection of the motors.
There is a red emergency stop on the box that you can use to turn the hoist
on and off and to disconnect the power supply in an emergency.
Under the emergency stop is the electrical emergency lower control to be
able to lower the lifting arm down in an emergency.
Below that is the screen where you can read the battery status, operating
hours and service check status.
The motors and handset can be placed under the control box.
2.2.1 Emergency stop button
Pressing the red emergency stop button will disconnect the battery power and the hoist will immediately stop
moving. The emergency stop is also used to switch the hoist on and off.
To activate the emergency stop, press the red emergency stop button.
To cancel the emergency stop, turn the red emergency stop button clockwise so that it returns to the
unpressed position.
Depress the emergency stop when you park the hoist. This prevents the batteries from slowly draining.
2.2.2 Electric emergency lower control
The electrical emergency lower control is used if there is a malfunction or defect outside the control box or
battery. The emergency operation switches off the motor brake and uses the last residual voltage of the
battery to lower the lifting arm, so this only works if the battery is installed.
Insert the tip of a pen, pencil or other thin object into the opening / window EMERGENCY.
The lift will lower the arm with the remaining battery power.
2.2.3 Display
There is a screen on the control box. You can read the battery status on this.
Battery Status
When the icon is completely coloured, the battery is full. It is recommended to charge the
battery when it falls below half. This prevents empty batteries and extends their life.
Use and Service Indication.
This appears on the screen when you briefly press the up button.
Here you can see how much the hoist has been used and when it needs to be serviced
(please see the next page).
Emergency Stop
Electric
Emergency
Lower
Manual Operation
Display
Lifting Motor CH1
Spreader Bar Powered Motor CH2
Leg Spreader
Motor

8 REF0717-2
Description 2
From this you can read how many cycles the lift motor has completed.
One cycle of the lifting motor stands for: a minimum of 5 seconds with more than 1.5A
current consumption, and a minimum of 2 seconds sent back.
Here you can read how much the lift motor is used in current per second (Ampere x
second).
This is a good reflection of how much the motor has run in total.
Here will display how often the hoist has lifted more than the maximum weight capacity.
From here you can see how long ago the hoist was last serviced (days).
For example, 90 / - means that the hoist was serviced 90 days ago.
It is possible to set a service interval. There will be, for example, 90/360 on the screen (360 ≈ one year). The
hoist must then be serviced again in 270 days. When the day counter reaches the 360 days, a light will
illuminate on the hand control and control box. The hoist must then be serviced and the engineer can reset it.
The service interval must be set by OpeMed (United Care).
2.3 Handset
The hoist is operated with a Handset/hand control. The curled cord on the hand control allows you to stand
next to the user during operation of the hoist. The hand control is used to:
• Move the hoist up or down.
• Electrically spread legs.
• Move the electric cradle from lying to sitting position.
The control buttons are shown below:
Raise arm up
Lower arm down
Cradle to Laying Position
Cradle to Sitting Position
Spread the legs
Close the legs
There is a mounting hook on the back of the hand control to hang it onto the hoist.
The curled cord is interchangeable/removable and therefore also available separately. Always pull the curled
cord out of the hand control carefully.
Removing the curled cord too hard can damage the hand control and is not covered by the warranty.

REF0717-2 9
Description 2
2.4 Lifting Motor
The Wendy is equipped with a powerful but quiet motor with a ball screw and safety nut.
The motor is connected to the control box. The hoist can be equipped with 2 types of lifting
motors. A fast motor for the 160kg Wendy and a strong motor for a 200 kg Wendy
There is a mechanical emergency lower control on the motor. Pull it up in an emergency
and the user will be lowered in a controlled manner. The emergency lower function always
needs a little weight in order to lower. The motor is plugged into the control box on port 1.
The specified service life of the motor is 10,000 cycles or 4,200,000 Amp x sec (see 2.2.1 -
page 7).
2.5 Battery
Two types of rechargeable batteries are available. Lead-containing (Pb) batteries and Lithium-Ion (Li-ion)
batteries. The hoist comes with one or two lead batteries as standard. Lead batteries are cheaper to purchase
and allow, even when the battery is almost empty, for the hoist to still be used with the rest of the electricity.
These batteries can reasonably last 2 to 3 years.
Li-ion batteries have a life span of approximately 5 times, are lighter, more environmentally friendly and can
be left unused for longer. The self-discharge is minimal. When a Li-ion battery is empty, there is no longer any
residual voltage available to complete a transfer.
If the Li-Ion battery remains unused for a week and is not charged, it will fall into sleep mode. It can
be taken out of sleep mode by putting it on the charger.
The battery is equipped with a simple fixing mechanism. At the rear of the battery is a handle with
which you can lock and unlock the battery on the Wendy. This is best done by pressing the battery
handle at the top during placement so that the lock is open when placed.
It is recommended to use two batteries: one in the hoist and one on the charger, so that a
reasonably charged battery is always present.
Always ensure that the battery is sufficiently charged before you start using the hoist.
2.5.1 Battery life
Capacity
The number of lifts that can be completed with a fully charged battery depends on the duration of the lifting
operations, the lifted weight and the condition of the battery.
To extend the lifespan, it is advisable to always keep the battery above 50% full in normal use. You can
discharge the battery once a year (1/2 year) up to 25% (or just below) and then fully charge it. This benefits the
life and power of the batteries.
PAY ATTENTION !! Too much discharge of a battery is again detrimental to the capacity.
Battery Drainage
A battery that is not used for a long period of time will run out. This applies to the battery in the hoist and to
the spare batteries separate from the hoist. This may cause the battery to break or lead to fewer lifts
completed with a fully charged battery.
It is recommended to charge each battery at least once a week.
Mechanical
Emergency Lower

10 REF0717-2
Description 2
2.6 Battery charger (32106680)
Batteries are charged using the supplied battery charger. This battery charger is separate from the hoist.
Batteries are placed on the battery charger in the same way as on the hoist control box.
It is recommended to mount the charger on the wall. This prevents damage to the charger, cord and battery
due to shifting, falling, etc. It is also clear where the charger is and you will not lose it.
A power cord is also supplied with the battery charger. One side fits in the charger and the other side
fits in the socket. First insert the plug into the charger and then the plug into the socket. Only then
should you place the battery on the charger.
2.6.1 Charging the batteries
To guarantee the longest possible service life of the batteries, it is important to regularly fully charge the
batteries. It is recommended to do this at least once a week.
You can see on the battery indication of the control box how full the battery is.
After any transfer or lift, charge the battery as soon as the battery indicator shows that the charge
level has fallen below 50%. If the battery indicator indicates that the charge level has fallen below
25%, it is advisable to charge the battery for further use.
Charge the battery according to the following procedure:
•Connect the battery charger to the mains.
•The "on" indicator light will come on.
•Remove the battery from the hoist and place it on the charger.
•Battery charging will start automatically.
•The charge light will illuminate during charging.
•When the battery is fully charged, the charge light will go out.
•Allow for a charging time of approx. 8 hours.
Depress the emergency stop when you park the hoist. This prevents batteries from being
drained by the control box.

REF0717-2 11
Description 2
2.7 Chassis
Both legs can be spread out to make room for obstacles e.g. a chair. The legs are electrically
adjustable by the buttons on the hand control. It’s advisable to transfer as much as possible with the
legs in the narrow position to prevent damage to the hoist or surrounding area.
2.7.1 Adjusting the legs of the Hoist
Make sure there is enough space to spread the legs. If the legs get stuck, this can damage the
hoist or its environment.
If parts of the leg adjustment need to be replaced, make sure that the legs are properly
adjusted. On the front and back of the frame next to the legs are set screws that remove
movement from the legs in the extreme positions. Loosen these set screws. Let the
motor run completely. Then adjust the legs perpendicular to the frame by turning the
M10 ball joints in or out of the frame. With the set screws you can remove the remaining
movement in both extreme positions. Do not over tighten!
This prevents problems with the motor or ball heads.
2.7.2 Wheels
The hoist has four swivel wheels, braked 100mm at the front and 125mm at the rear. The rear wheel brake
stops the wheel from rolling and the direction of rotation. Apply the brake using the tip of the foot. Always do
this with care.
The wheels have a very low rolling resistance due to the fully ball-bearing pivot points.
Moving the hoist from a standstill requires minimal force if the wheels of the chassis are already in line with
the direction of travel.

12 REF0717-2
Description 2
2.9 Cradle
The Wendy hoist is equipped with a cradle. The cradle is a frame to which the sling is attached, by means of
clips or loops, where the user will be sat. The cradle is connected to the lifting arm by means of a coupling
piece. This coupling piece ensures that the cradle can rotate and tilt freely, so that a smooth transfer can be
made y maintaining balance. There are two types of cradles available: the X-Shape Spreader Bar and the
Powered/Electric Cradle.
Manual Cradle
A manual cradle moves comfortably, under the influence of the patient's posture, in a
sitting or lying position. You can move the person in a lying or sitting position to be able to
place him or her in a chair or bed. The manual cradle is most suitable for users with
sufficient stability in their hips and with sufficient trunk balance. Users who make many
uncontrolled movements can also be lifted with a manual cradle.
Electric Cradle
An electric Cradle is brought into a sitting or lying position using the motor on the cradle.
With this, the patient can be helped in to the desired position, which is useful for patients
with poor hip stability. The electric cradle is operated with two buttons on the hand
control.
Two-point Spreader Bar
The two-point spreader bar is used in combination with loop slings. These loops can be hung
on the hooks of the two-point spreader bar. Due to the different lengths of loops, the user
can be lifted both lying down and sitting.
2.10 Slings
When hoisting, the user is placed in a hammock-shaped sling and is attached to the
cradle/spreader bar with clips or loops. There are different types and sizes of slings,
each with their own application (page 16). Some users may only be hoisted with a
certain type of sling.
Use the Wendy in combination with a sling supplied by United Care. If you intend to
use a different type of sling, please contact United Care.
Always use a well-fitting sling. The model is in the label that is sewn on sling. It says
the type, model, size, serial number, etc. Always leave the label on the sling.
Always follow the agreements made about the type of sling with which the user
must be lifted. Check the sling regularly for wear.
Check the tape and clips for damage before use. Before and during hoisting, check that the clips are positioned
correctly.

REF0717-2 13
Description 2
2.10.1 Boning/Ribs
The sling must support the user in both a sitting and a laying position. For additional support of
the head and neck, two plastic ribs must be placed in the slots provided on the main side
(figure 16).
2.10.2 Attachment to the hoist
Read these instructions carefully before using the sling.
Always check the sling for damage and wear.
It is essential that you fully understand how the sling must be hung from the cradle.
UCP clip (C)
1. Hold the clip strip with one hand, and pull the large hole of the clip over
the head of the attachment point/hook point on the hoist, check that the
strap (with which the clip is attached to the sling) is not twisted.
2. Grasp the strap under the clip of the sling and pull it down
3. Pull the clip so that the hook point is securely held. The hook point is now
locked in the hole at the top of the clip.
iQ clip (Q)
1. Before attaching (and removing) the clip, release the tension from the
sling. Hold the clip with one hand and push the latch open with your
thumb. You can also press the clip over the hook point instead of
opening it first.
Check that the strap that holds the clip on the sling is not twisted.
2. Hook the clip over the hook point and pull it down. The clip will click.
3. The clip is now locked and secured. Due to the tension on the sling, the
clip can never come off. Half mounting isn’t possible thanks to the
design of clip.
Loops (P)
1. Place the sling beneath the user. The leg flaps must be connected to the cradle crossing one another
or along a middle loop.
2. Use the long loop for legs and short for shoulders for sitting position and the short loop for legs and
long for shoulder for lying position.
3. Hook the loops onto the spreader bar. Make sure the locking clip closes after applying the loop.
2.10.3 Types and dimensions
Different people, use and transfers require different slings. An overview of the possible types of sling and their
usability is shown in the table on p.14-2.10.4.
The following issues play a role in the dimensions of the slings: weight, height and size of the patient, degree of
stability of the hip, pain, amputation etc.
Standard United Care slings have a maximum lifting weight of 230 kg (unless stated otherwise).
The last digit and letter of the article number represent the dimensions (X) of a sling and the type of
suspension (Y). The dimensions range from 0 to 6 (see 2.10.4 page 14). The size is also indicated by the colour
of the clips and the label in the sling. In addition, the suspension method is indicated by C (UCP clips), Q (iQ
clips) or P (loops).

14 REF0717-2
Description 2
2.10.4 Sling Size Table
X = Size Indication: 0 t/m 6
Y = Suspension Mode: C = 4x UCP clips
Q = 4x iQ-clips
P = 4x loops
Code
Size
Crown-bottom height
Purple
0
XXS
45-60 cm
Brown
1
XS
60-80 cm
Red
2
S
80-87 cm
Yellow
3
M
85-90 cm
Green
4
L
90-97 cm
Blue
5
XL
95-102 cm
Orange
6
XXL
102-106 cm
Type of sling
Part No.
Description
Standard Sling
Material: Polyester
3010905 XY
The standard sling is used for short transfers. We advise the user not to sit
on this sling for more than an hour.
Standard Mesh Sling
Material: Mesh Poly
3010904 XY
Do not leave the user on this sling beyond bathing. The fabric of this sling
has large mesh so that it dries faster.
Standard Ezeslyde Sling
Material: Silk Poly
3010150 XY
Do not leave the user on this sling for longer than an hour. The smooth
material makes applying the sling extra easy, especially for wheelchair use.
Long Stay
Materiaal: 3D spacer
3010910 XY
Long Stay Plus
Materiaal: 3D spacer
3010910 XY
The user can sit comfortably on this sling all day long. This is possible
because the material is soft and breathable.
Long Stay Comfort
Material: Bamboo & Polyester
3010187 XY
The user can sit comfortably on this sling all day long. This is possible
because the material is soft and breathable.
Toilet Sling Luxe
Material: Polyester
3010960 XY
Remove the sling from the chair after the transfer of the patient. Toilet
sling can only be used safely with users with sufficient shoulder function
and trunk stability.
Mesh Sling Anti-Spasm
Material: Polyester Mesh
3010193 XY
Do not leave the person on this sling beyond bathing. The fabric of this sling
has large mesh so that it dries faster. This sling has a special shape that
allows a fetal position transfer.
Long Stay Anti-Spasm
Material: Polyester 3D spacer
3010902 XY
The user can sit comfortably on this sling all day long. This is possible
because the material is soft and permeable to oxygen. This sling has a
special shape that allows a fetal position transfer.
Long Stay Plus Anti-Spasm
Material: Polyester 3D spacer
3010912 XY
The user can sit comfortably on this sling all day long. This is possible
because the material is soft and permeable to oxygen. This sling has a
special shape that allows a fetal position transfer.
Long Stay Comfort Anti-Spasm
Material: Bamboe stof & Polyester
3010960 XY
The user can sit comfortably on this sling all day long. This is possible
because the material is soft and permeable to oxygen. This sling has a
special shape that allows a fetal position transfer.
Mesh Amputee Sling
Material: Polyester Mesh
3010154 XY
Do not leave the user on this sling beyond bathing. The fabric of this sling
has large mesh so that it dries faster.
Long Stay Amputee
Material: Polyester 3D spacer
3010155 XY
The user can sit comfortably on this tire all day long. This is possible
because the material is soft and breathable.
Long Stay Comfort Amputee
Material: Bamboo & Polyester
3010158 XY
The user can sit comfortably on this tire all day long. This is possible
because the material is soft and breathable.

REF0717-2 15
Description 2
2.10.5 Washing instructions for the sling
Every United Care sling has a label on displaying washing instructions. Such a label is
shown in the image below. You can see how the slings can be washed which can
sometimes vary due to the use of different types of materials.
Slings can be machine washed at 60 degrees (if different, see pictogram).
Sling is only allowed in the dryer at low temperature
Sling is not allowed in the dryer
Not suitable for chemical cleaning
Do not use bleach
Do not iron the sling
Always check the sling before and after washing for wear and defects.
Remove the plastic ribs from the sling before it is washed or disinfected.
When disinfecting, use the correct concentration as indicated on the package of the
product.
It is important that the sling is in good condition. The condition of a sling is partly determined by the way in
which it is washed or disinfected.

16 REF0717-2
Use 3
3.1 Introduction
Check the Wendy before use on the following points:
•Switch on the hoist by turning the emergency stop clockwise
•Check if the battery is sufficiently charged.
•Check the condition of the sling and the condition of the clips
•The hoist is ready for use. Always ensure a neat and clean working environment.
3.2 Attach the Sling
Make sure that the user is able to be lifted!
Make sure that the plastic ribs are fitted in the main part of the sling!
Attach the clips and loops accurately (2.10.2 - page 13)!
Ensure use of the right type and size of sling. Always inform the user clearly of what is going to happen with
each operation.
3.2.1 Applying a toileting sling
Fit the toilet sling in the same way as the standard sling, but with the following points of
attention:
•Insert the user’s arms through the loops on the main side of the sling with the
round pads under the armpits (marked in the illustration).
•Bring the leg slips along the outside of their legs, then under their legs and both
slips up again on the inside.
•Now place the clips (loops) on the cradle/spreader bar of the Wendy.
Toilet slings can only be used safely by those with sufficient shoulder function
and trunk stability. A toilet sling is not for long-term use and therefore not
suitable as a general sling.
3.2.2 Apply the sling while seated
• Fit the sling behind the back of the user on the seat. Let them sit a little forward in the seat.
• Position the sling so that the washing instructions label is on the outside.
• Guide both leg slips of the sling along the buttocks of the user.
• Then pull both legs slightly forward. In this way, the user is already sat within the sling.
• Lift one of the user’s legs and bring one leg slip under their leg to the inside of their leg.
• Then apply the other leg slip in the same way.
• If necessary, pull the main side of the sling up to the correct height. The sling is now
around user.

REF0717-2 17
Use 3
3.2.3 Apply the sling from a laying position
•Fold the sling in half lengthwise a few times. One half folded and one half loose.
•Turn the user on the side, towards you.
•Place folded side of the sling against the user’s back.
•Position the sling so that the label with washing instructions is on the outside (currently the bottom).
•Turn the user over the sling on the other side.
•The folded part of the sling ends up on your side.
•Unroll the folded part of the sling and pull it further into the correct position.
•Now turn the user onto their back so that they lay on the rolled-up sling.
•Lift one of the user’s legs and bring one leg slip under their leg to the inside of their leg.
•Then apply the other leg slip in the same way.
•If necessary, straighten the sling so that the user is stable in the sling when hoisting.

18 REF0717-2
Use 3
3.3 Hoisting
Before hoisting, place the cradle in the position in which the user is to be lifted.
•Drive the hoist with care.
•If necessary, widen the frame with the help of the leg adjustment so that the lift can be placed closer
to a chair or bed.
•Pay attention! Drive carefully when nearing objects or users!
Attach the sling to the cradle (see also 2.10.2, page 12).
•Ensure that the user is facing the cradle.
•Attach the two clips from the main side of the sling to the attachment points of the main side of the
cradle.
•Then attach the two clips from the leg side of the sling to the fixing points of the leg side of the cradle.
Ensure that the bands of the clips are straight; the sling must not be turned.
When using a two-point spreader bar, the leg slips of the loop sling must be applied across one
another. Left slip on right spreader hook and right slip on left spreader hook.
•Check the position of the person's arms. With standard slings, place the user’s arms inside the sling,
e.g. resting on their lap.
•For toilet slings, the user's arms must be kept outside the sling.
•Take the hand control and stand as close as possible to the user. Move the hoist up a little so that
there is tension on all clips.
•Check all fixing points again.
•Tell the user that hoisting will begin.
•Lift the user up.
3.3.1 Hoisting to the toilet
•Before putting the user on the toilet, lower the user’s trousers/garments down to the kneecap, and
do not lower them until the user has been put fully on the toilet.
•Disconnect the toilet sling from the fixing points of the cradle during toileting.
•After the toilet visit, bring their clothing back up over the knees, lift them and then put the clothing
back on completely.

REF0717-2 19
Use 3
3.4 Driving
Do not lift the user higher than necessary when moving the hoist.
•Moving the hoist is easiest if the wheels are in the right direction (in line with the direction of travel).
•Walk with the hoist when moving.
•Drive the hoist to the destination and only lift it to the required height to bring the patient into the
final position.
•The legs may be in the wide or narrow position when the hoist is moving. Preferably use the narrow
position to move.
•Do not drive too fast.
3.4.1 Turning with the Hoist
•Avoid turning from behind when turning the hoist. While turning, stand to the side of the hoist and
use the arm, cradle, and legs to pull or push.
•Hold the cradle or lifting arm with one hand and the mast with the other hand.
•Start the turn by pushing the base with one foot.
•Continue the turn with your arm resting on the cradle and the lifting arm to push the hoist further.
3.5 Removing the user from the Hoist
Lifting to a bed / chair
Bring the user into the final intended position (laying or sitting). Position the user as well as possible and lower.
•Ensure that the user is placed properly in the back of a chair.
•Do not apply the brake on the hoist in order to position the user properly.
•Release all clips from the sling.
•Drive the hoist away.
•Remove the sling (unless a personal sling is used).
•Press in the emergency stop and return the hoist where it belongs.
(Charge the battery if necessary)