Unitronics Uni-I/O UIA-0800NH User manual

Unitronics
1
Uni-I/O™
Modules
Installation Guide
UIA-0800NH
SCAN
to download
Uni-I/O™ is a family of Input/Output modules that are compatible with the UniStream®
control platform.
This guide provides basic installation information for the UIA-0800NH module.
Technical specifications may be downloaded from the Unitronics website.
The UniStream® platform
comprises CPU controllers, HMI
panels, and local I/O modules
that snap together to form an
all-in-one Programmable Logic
Controller (PLC).
Install Uni-I/O™ modules:
Onto the back of any
UniStream® HMI Panel
comprising a CPU-for-Panel.
Onto a DIN-rail, using a
Local Expansion Kit.
The maximum number of Uni-I/O™ modules that can be connected to a single CPU
controller is limited. For details, please refer to the specification sheets of the UniStream®
CPU or any of the relevant Local Expansion Kits.
Before You Begin
Before installing the device, the installer must:
Read and understand this document.
Verify the Kit Contents.
Installation option requirements
If you are installing a Uni-I/O™ module onto:
A UniStream® HMI Panel; the Panel must comprise a CPU-for-Panel, installed according
to the CPU-for-Panel installation guide.
A DIN-rail; you must use a Local Expansion Kit, available by separate order, to integrate
the Uni-I/O™ modules on the DIN-rail into a UniStream® control system.
Alert Symbols and General Restrictions
When any of the following symbols appear, read the associated information carefully.
Symbol
Meaning
Description
Danger
The identified danger causes physical and property damage.
Warning
The identified danger could cause physical and property damage.
Caution
Caution
Use caution.
All examples and diagrams are intended to aid understanding, and do not guarantee

UIA-0800NH Installation Guide
2
Unitronics
operation. Unitronics accepts no responsibility for actual use of this product based on
these examples.
Please dispose of this product according to local and national standards and regulations.
This product should be installed only by qualified personnel.
Failure to comply with appropriate safety guidelines can cause severe injury or
property damage.
Do not attempt to use this device with parameters that exceed permissible levels.
Do not connect/disconnect the device when power is on.
Environmental Considerations
Ventilation: 10mm (0.4”) of space is required between the device top/bottom edges
and the enclosure’s walls.
Do not install in areas with: excessive or conductive dust, corrosive or flammable
gas, moisture or rain, excessive heat, regular impact shocks or excessive vibration,
in accordance with the standards and limitations given in the product’s technical
specification sheet.
Do not place in water or let water leak onto the unit.
Do not allow debris to fall inside the unit during installation.
Install at maximum distance from high-voltage cables and power equipment.
Kit Contents
1 UIA-0800NH module
4 I/O terminal blocks (2 black and 2 gray)
UIA-0800NH Diagram
1
DIN-rail clips
Provide physical support for CPU and modules. There are two
clips: one at the top (shown), one at the bottom (not shown).
2
Inputs 0-1
Input connection points
3
Inputs 2-3
4
I/O Bus - Left
Left-side Connector
5
Bus Connector
Lock
Slide the Bus Connector Lock to the left, to electrically connect
the Uni-I/O™ module to the CPU or adjacent module.
6
I/O Bus - Right
Right-Side Connector, shipped covered. Leave covered when not
in use.
Bus Connector

Uni-I/O™
Unitronics
3
Cover
7
Inputs 6-7
Input connection points
8
Inputs 4-5
9
Input LEDs (4-7)
Red LEDs
10
Input LEDs (0-3)
Red LEDs
11
Status LED
Tricolor LED, Green/Red/Orange
NOTE
Refer to the module's specification sheet for LED indications.
12
Module door
Shipped covered with protective tape to prevent the door from
being scratched. Remove tape during installation.
13
Screw holes
Enable panel-mounting; hole diameter: 4mm (0.15”).
About the I/O Bus Connectors
The I/O Bus connectors provide the physical and electrical connection points between
modules. The connector is shipped covered by a protective cover, protecting the connector
from debris, damage, and ESD.
The I/O Bus - Left (#4 in diagram) can be connected to either a CPU-for-Panel, a
Uni-COM™ module, to another Uni-I/O™ module or to the End Unit of a Local Expansion
Kit.
The I/O Bus - Right (#6 in diagram) can be connected to another I/O module, or to the
Base Unit of the Local Expansion Kit.
Caution
If the I/O module is located last in the configuration, and nothing is to be
connected to it, do not remove its Bus Connector Cover.
Installation
Turn off system power before connecting or disconnecting any modules or devices.
Use proper precautions to prevent Electro-Static Discharge (ESD).
Installing a Uni-I/O™ Module onto a UniStream® HMI Panel
NOTE
The DIN-rail type structure on the back of the panel provides the physical support for
the Uni-I/O™ module.
1. Check the unit to which you will connect the Uni-I/O™ module to verify that its Bus
Connector is not covered.
If the Uni-I/O™ module is to be the last one in the configuration, do not remove the
cover of its I/O Bus Connector - Right.

UIA-0800NH Installation Guide
4
Unitronics
2. Open the door of the Uni-I/O™
module and hold it as shown in the
accompanying figure.
3. Use the upper and lower guide-
tunnels (tongue & groove) to slide
the Uni-I/O™ module into place.
4. Verify that the DIN-rail clips
located at the top and bottom of
the Uni-I/O™ module have
snapped onto the DIN-rail.
5. Slide the Bus Connector Lock all the way to
the left as shown in the accompanying figure.
6. If there is already a module located to its
right, complete the connection by sliding the
Bus Connector lock of the adjacent unit to the
left.
7. If the module is the last in the configuration,
leave the I/O bus connector covered.
Removing a Module
8. Turn off the system power.
9. Disconnect the I/O terminals (#2,3,7,8 in the diagram).
10. Disconnect the Uni-I/O™ module from the adjacent units: slide its Bus Connector Lock
to the right. If there is a unit located on its right, slide the lock of this module to the
right as well.
11. On the Uni-I/O™ module, pull the top DIN-rail clip up and the bottom clip down.
12. Open the door of the Uni-I/O™ and hold it with two fingers as shown in the figure on
page 3; then pull it carefully from its place.
Installing Uni-I/O™ modules onto a DIN-rail
To mount modules onto a DIN-rail, follow steps 1-7 in Installing a Uni-I/O™ Module onto a
UniStream® HMI Panel on page 3.
In order to connect the modules to a UniStream® controller, you must use a Local
Expansion Kit.
These kits are available with and without power supplies, and with cables of varying
lengths. For complete information, please refer to the installation guide of the relevant
Local Expansion Kit.
Numbering Modules
You can number modules for reference purposes. A set of 20 stickers is provided with
every CPU-for-Panel; use these stickers to number the modules.

Uni-I/O™
Unitronics
5
The set contains numbered and blank stickers
as shown in the figure to the left.
Place them on the modules as shown in the
figure to the right.
Wiring
This equipment is designed to operate only at SELV/PELV/Class 2/Limited Power
environments.
All power supplies in the system must include double insulation. Power supply
outputs must be rated as SELV/PELV/Class 2/Limited Power.
Do not connect either the ‘Neutral’ or ‘Line’ signal of the 110/220VAC to device’s 0V
point.
Do not touch live wires.
All wiring activities should be performed while power is OFF.
Unused points should not be connected (unless otherwise specified). Ignoring this
directive may damage the device.
Double-check all wiring before turning on the power supply.
Caution
To avoid damaging the wire, use a maximum torque of 0.5 N·m (5 kgf·cm).
Do not use tin, solder, or any substance on stripped wire that might cause the
wire strand to break.
Install at maximum distance from high-voltage cables and power equipment.
Wiring Procedure
Use crimp terminals for wiring; use 26-12 AWG wire (0.13 mm2–3.31 mm2).
1. Strip the wire to a length of 7±0.5mm (0.250–0.300 inches).
2. Unscrew the terminal to its widest position before inserting a wire.
3. Insert the wire completely into the terminal to ensure a proper connection.
4. Tighten enough to keep the wire from pulling free.
UIA-0800NH Connection Points
All wiring diagrams and instructions in this
document refer to the UIA-0800NH connection
points.
These points are arranged in four groups of 7
points as shown in the figure to the right.
Two top groups
Input connection points (0,1,2,3)
Two bottom groups
Input connection points (4,5,6,7)

UIA-0800NH Installation Guide
6
Unitronics
Wiring Guidelines
In order to ensure that the device will operate properly and to avoid electromagnetic
interference:
Use a metal cabinet. Make sure the cabinet and its doors are properly earthed.
Use wires that are properly sized for the load.
Use shielded twisted pair cables for wiring Analog I/O signals;
do not use the cable shield as a signal common (CM) / return path.
Route each I/O signal with its own dedicated common wire. Connect common wires at
their respective common (CM) points at the I/O module.
Individually connect each 0V point and each common (CM) point in the system to the
power supply 0V terminal, unless otherwise specified.
Individually connect each functional ground point ( ) to the earth of the system
(preferably to the metal cabinet chassis).
Use the shortest and thickest wires possible: less than 1m (3.3’) in length, minimum
thickness 14 AWG (2 mm2).
Connect the power supply 0V to the earth of the system.
Earthing the cables' shield:
Connect the cable shield to the earth of the system - preferably to the metal cabinet
chassis. Note that the shield must be connected only at one end of the cable;
typically, earthing the shield at the UIA-0800NH end performs better.
Keep shield connections as short as possible.
Ensure shield continuity when extending shielded cables.
NOTE
For detailed information, refer to the document System Wiring Guidelines, located in
the Technical Library in the Unitronics’ website.
Wiring the Analog Inputs
NOTE
The inputs are not isolated.
Each input has its own common point (CM0 for I0, etc.).
2-wire
3-wire

Uni-I/O™
Unitronics
7
4-wire

UIA-0800NH Installation Guide
8
Unitronics
The information in this document reflects products at the date of printing. Unitronics reserves the right, subject to all applicable laws, at any time, at its sole discretion, and without notice, to
discontinue or change the features, designs, materials and otherspecifications of its products, and to either permanently or temporarily withdraw anyof the forgoing from the market.
All information in this document is provided "as is" withoutwarranty of any kind, either expressed or implied, including but not limited to any implied warranties of merchantability, fitness for
a particular purpose,or non-infringement. Unitronicsassumes no responsibility for errors or omissions in the information presented in this document. In no event shallUnitronics be liable
for any special, incidental, indirect orconsequential damages of any kind, orany damages whatsoever arising out of or in connection with the use or performance of this information.
The tradenames, trademarks, logos and service marks presented in this document, including their design, are the property of Unitronics (1989) (R"G) Ltd. or other third parties and you are
not permitted to use them without the prior written consent of Unitronics or such third party as may own them
DOC27027-A4 ] 12/18