Unitronics Vision OPLC V100-17-CAN User manual

Unitronics
Vision™ OPLC™ Installation Guide, CANbus Module V100-17-CAN,V100-S-CAN
This guide provides instructions for installing the CANbus communication module
(V100-17-CAN (CANbus) , V100-S-CAN (CANbus-Wide Temperature)
in a Vision130™ or Vision350™ or Vision430™ or SM35™ or SM43™ or SM70™ controller.
Danger Symbols
When any of the following symbols appear, read the associated information carefully.
Symbol Meaning Description
Danger The identified danger causes physical and property damage.
Warning The identified danger could cause physical and property damage.
Caution Caution Use caution.
Before using this product, the user must read and understand this document.
All examples and diagrams are intended to aid understanding, and do not guarantee operation.
Unitronics accepts no responsibility for actual use of this product based on these examples.
Please dispose of this product according to local and national standards and regulations.
Only qualified service personnel should open this device or carry out repairs.
Failure to comply with appropriate safety guidelines can cause severe injury or property
damage.
Do not attempt to use this device with parameters that exceed permissible levels.
To avoid damaging the system, do not connect/disconnect the device when power is on.
Environmental Considerations
Do not install in areas with: excessive or conductive dust, corrosive or flammable gas,
moisture or rain, excessive heat, regular impact shocks or excessive vibration.
Do not place in water or let water leak onto the unit.
Do not allow debris to fall inside the unit during installation.
General
Turn off power before making communications connections.
Do not touch live wires
Unused pins should not be connected. Ignoring this directive may damage the device.
Double-check all wiring before turning on the power supply.
Installation Instructions
Before performing these actions, touch a grounded object to discharge any electrostatic
charge.
Avoid touching the PCB board directly. Hold the PCB board by its connectors.
Caution
Installing modules also requires you to remove and replace PCB boards already installed
in the controller.
Make certain that the pins fit correctly into their matching receptacle.

3/15 V100-17-CAN,V100-S-CAN
2 Unitronics
Installation in a V130/V350/SM35 controller
Opening the Controller
1. Turn off the power supply, disconnect,
and dismount the controller.
2. The back cover of the controller
comprises 4 screws, located in the
corners. Remove the screws, and pull off
the back cover.
3. Hold the I/O PCB board by its top and
bottom connectors and steadily pull the
board off.
Note that if you are installing both a V100-17-CAN, V100-S-CAN module and either V100-17-RS4/X
or V100-17-ET2, V100-S-ET2 or V100-17-PB1 modules, you should install the V100-17-RS4/X
or V100-17-ET2, V100-S-ET2 or V100-17-PB1 modules first.
Installing V100-17-CAN, V100-S-CAN
1. Remove the plastic tab marked X.
2. Plastic tab X comprises a cutout that covers the
CANbus port location. Snip through the cutout
holders and remove the cutout.
3. On the V100-17-CAN, V100-S-CAN, locate the:
- white plastic pin. The main board comprises
an insertion point for this pin.
- 6-pin female CANbus connector.The main
board comprises a male 6-pin CANbus connector.
4. Insert the module as shown in the accompanying
figure.
Caution Make certain that the pins fit correctly into their
matching receptacle.
5. When the module is properly installed in the
controller, it is held in place by the white plastic pin.
6. Replace the plastic tab marked X and then
close the controller as shown below.
Note that in order to remove the module; you
must compress the ends of the white pin with a
pair of pliers while pulling the module out of the
controller.
Closing the controller
1. Replace the I/O board.
2. Close the controller by snapping the plastic
cover back in its place. If the card is placed
correctly, the cover will snap on easily.
3. Replace the screws in the corners of the back cover.

Installation Guide V130/V350/V430/SM35/SM43/SM70 CANbus Module
3/15
Unitronics
Installation in a V430/SM43 controller
Opening the Controller
1. Turn off the power supply,
disconnect and dismount the controller.
2. The back cover of the controller
comprises 4 screws, located in the corners.
Remove the screws, and pull off the back
cover.
3. Hold the I/O PCB board by its top and
bottom connectors and steadily pull
the board off.
Installing V100-17-CAN, V100-S-CAN
1. Break the plastic tab marked X.
2. Plastic tab X comprises a cutout that covers
the CANbus port location.
3. locate the white plastic pin and remove it by
compressing the ends of the white pin with a
pair of pliers.
4. Insert the module as shown in the
accompanying figure.
6-pin female CANbus connector. The main
board comprises a male 6-pin CANbus
connector.
Caution Make certain that the pins fit correctly
into their matching receptacle.
Closing the controller
1. Replace the I/O board.
2. Close the controller by snapping the plastic
cover back in its place. If the card is placed
correctly, the cover will snap on easily.
3. Replace the screws in the corners
of the back cover.

3/15 V100-17-CAN,V100-S-CAN
4 Unitronics
Installation in a SM70 controller
Opening the Controller
1. Open the door marked
“Battery & Communication Module
Cover”,under the arrow direction.
2. Break the plastic tab marked X.
3. Plastic tab X comprises a cutout that
covers the CANbus port location.
Installing V100-17-CAN, V100-S-CAN
1. locate the black plastic pin.
2. Install the module as shown in the
accompanying figure 6-pin female CANbus
connector.The main board comprises a
male 6-pin CANbus connector
Caution
Make certain that the pins fit correctly
into their matching receptacle
Closing the controller
1. Close the controller by closing the Door
marked “Battery & Communication Module
Cover” back in its place.
The information in this document reflects products at the date of printing. Unitronics reserves the right, subject to all applicable laws, at any time, at its
sole discretion, and without notice, to discontinue or change the features, designs, materials and other specifications of its products, and to either
permanently or temporarily withdraw any of the forgoing from the market.
All information in this document is provided "as is" without warranty of any kind, either expressed or implied, including but not limited to any implied
warranties of merchantability, fitness for a particular purpose, or non infringement. Unitronics assumes no responsibility for errors or omissions in the
information presented in this document. In no event shall Unitronics be liable for any special, incidental, indirect or consequential damages of any kind,
or any damages whatsoever arising out of or in connection with the use or performance of this information.
The tradenames, trademarks, logos and service marks presented in this document, including their design, are the property of Unitronics (1989) (R"G)
Ltd. or other third parties and you are not permitted to use them without the prior written consent of Unitronics or such third party as may own them
DOC14002 A9 03/15