Universal Furniture 987-923 User manual

GOOD, AFFORDABLE, SMART DESIGN
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small
parts that may have come loose inside the carton during shipment.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the
assistance of one or more persons in order to prevent personal injury and to insure parts are not damaged
during the assembly process. If dirty, clean finished parts with mild dishwashing liquid and water solution
applied on damp cloth. Cloth should not be excessively wet. Polish finish with soft cloth and an industry
recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residue and rough surfaces and also check for staples or nails left after removing the packaging material.
The manufacturer will not be held responsible if preventative steps are not taken prior to installation.
(3) Unpack and dispose of all packing material but be careful not to throw away any assembly parts or
hardware. Read the instruction sheet and parts list carefully. Remove all staples and screws used for
packaging carefully using pliers and or screwdrivers to prevent injury and scratching or damaging flooring.
(4) During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be
periodically inspected and re-tightened to prevent damage to the furniture and (or) personal property or cause
injury. Always check to be sure all hardware on this list and the above mentioned components is attached to
the furniture properly and kept tightened at all times.
PARTS LIST:
#
Description
Qty.
#
Description
Qty.
A
Entertainment Hutch
1pc
B
Entertainment console
1pc
C
Left Pier
1pc
D
Right Pier
1pc
E
Side panels
2pcs
F
Middle back panels
2pcs
G
Top frame unit
1pc
H
Top sliding doors
2pcs
I
Upper strips
2pcs
J
Bottom strips
2pcs
K
Hardware pack
1bag
L
Hardware pack
1bag
M
Hardware pack
1bag
Note: The tipping restraint kits are located on the back of right bookcase (C) and left bookcase (B). Always use
tipping restraint kits for safety.
Assembly Procedure: (Please follow the sketches below.)
Step 1: Unpack, inspect, and read assembly instruction carefully. Lay out the parts and hardware.
Make sure the quantity of each is correct.
Step 2: Disregard this step when the hutch (A) is not in use. Connect the two middle back panels (F)
with the screws (5) by a phillips head screwdriver (not provided). Then attach the side panels
(E) to the assembled middle back panel (F) with phillip head bolts (2) and allen wrench (4)
from hardware pack (K), attach the top frame unit (G) to the base of hutch with phillip head
bolts (1) and allen wrench (4) as shown, attach the sliding doors (H) to the top frame unit (G).
Secure the back rail with phillip head bolts (3) by allen wrench (4) as shown. Tighten all bolts
with allen wrench (4). Now the hutch (A) is assembled.
Step 3: Disregard this step when left pier (C) and right pier (D) are in use. Attach the upper strips (I)
to entertainment console (B) by hand. Attach the bottom strips (J) to console (B) with the
phillip head bolts(1), lock washers (2) and flat washers (3) by the wrench (4) from hardware
pack (L). Disregard the following steps when the piers (C&D) and hutch (A) are not in use.
Step 4: Put the entertainment hutch (A) on the entertainment console (B) as shown. Secure them
with mending plates (1) and screws (2) from hardware pack (M) by a phillips head
INSTRUCTION SHEET
987/988-922/923/968/969
Entertainment Desk

screwdriver (Not provided). Disregard the following steps when the piers (C&D) are not in
use.
Step 5: Position left and right piers (C&D) next to the entertainment console (B) and hutch (A) as
shown.
Note: To level the entertainment console (B) and piers (C&D), follow below steps.
Open the door, take off the plastic covers and level the cases by turning the leveler at its
bottom as necessary.
Assembly is now complete.
5
Step 2
G
3
Phillip head
bolt
Phillip head
bolt
Phillip head
bolt
Allen Wrench
Screw
Hardware pack (K)

J
IJ
I
I
J
J
4
3
2
Step 3
1
Step 4
A
B
Hardware pack (L)
Hardware pack (M)
Mending
plate
Screw
Phillip head
bolt
Lock washer
Flat washer
Wrench

B