Universal Furniture EXPLORE HOME 475-920 User manual

Page 1of 4
INSTRUCTION SHEET
475/476-920/921/963/965/966
Entertainment Wall
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small
parts that may have come loose inside the carton during shipment.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the
assistance of one or more persons in order to prevent personal injury and to insure parts are not damaged
during the assembly process. If dirty, clean finished parts with mild dishwashing liquid and water solution
applied on damp cloth. Cloth should not be excessively wet. Polish finish with soft cloth and an industry
recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residue and rough surfaces and also check for staples or nails left after removing the packaging material.
The manufacturer will not be held responsible if preventative steps are not taken prior to installation.
(3) Unpack and dispose of all packing material but be careful not to throw away any assembly parts or
hardware. Read the instruction sheet and parts list carefully. Remove all staples and screws used for
packaging carefully using pliers and or screwdrivers to prevent injury and scratching or damaging flooring.
(4) During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be
periodically inspected and re-tightened to prevent damage to the furniture and (or) personal property or cause
injury. Always check to be sure all hardware on this list and the above mentioned components is attached to
the furniture properly and kept tightened at all times.
PARTS LIST:
#
Description
Qty.
#
Description
Qty.
A
Middle back panel
1pc
B
Right pier
1pc
C
Left pier
1pc
D
Hutch top
1pc
E
Entertainment Hutch
1pc
F
Entertainment console
1pc
G
Shelf glass
6pcs
H
Hardware pack
1bag
Assembly Procedure: (Please follow the sketches below.)
Step 1: Unpack, inspect, and read assembly instruction carefully. Lay out the parts and hardware.
Make sure the quantity of each is correct.
Step 2: Attach right pier (B) and left pier (C) to middle back panel (A) with allen head bolt (1) using
allen wrench (4) from the hardware pack (H). Then attach hutch top (D) to right pier (B) and
left pier (C) with dowels (3) and screw up with screws (2).
Step 3: Place the entertainment hutch (E) onto the entertainment console (F) and screw up with
screws (2) from back side as below shown.
Step 4: Install shelf glass (G) with shelf pin (5).
Note: It is best two or more persons are involved.
Assembly is now complete.

Page 2of 4
INSTRUCTION SHEET
475/476-920/921/963/965/966
Entertainment Wall
DOWEL
SCREW
ALLEN
HEAD BOLT
A
B
C
D
D
Step 2
1
4
32
ab
cde
f
fg

Page 3of 4
INSTRUCTION SHEET
475/476-920/921/963/965/966
Entertainment Wall
E
F
Step 3
2
5
G
Step 4

Page 4of 4
INSTRUCTION SHEET
475/476-920/921/963/965/966
Entertainment Wall
Wiring Instruction On the Back
After you assemble the entertainment hutch with left and right pier, pls
connect the wire referring to step 2. First, connect the left wire (d) of the power
box with the right wire (c) on the right pier, and then connect the right wire (b)
of the power box with the left wire (a) on the right pier. Next, connect the middle
wire (e) on the right pier with one end of the wire (f) on the back panel of hutch,
and meanwhile connect the other end of the wire (f) on the back panel of hutch
with the wire (g) on the left pier.
Wiring is now complete.