Universal Furniture 988-657 User manual

Thank you for purchasing this quality product. Be sure to check all packing material carefully for small
parts that may have come loose inside the carton during shipment.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the
assistance of one or more persons in order to prevent personal injury and to insure parts are not damaged
during the assembly process. If dirty, clean finished parts with mild dishwashing liquid and water solution
applied on damp cloth. Cloth should not be excessively wet. Polish finish with soft cloth and an industry
recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residue and rough surfaces and also check for staples or nails left after removing the packaging material.
The manufacturer will not be held responsible if preventative steps are not taken prior to installation.
(3) Unpack and dispose of all packing material but be careful not to throw away any assembly parts or
hardware. Read the instruction sheet and parts list carefully. Remove all staples and screws used for
packaging carefully using pliers and or screwdrivers to prevent injury and scratching or damaging flooring.
(4) During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be
periodically inspected and re-tightened to prevent damage to the furniture and (or) personal property or cause
injury. Always check to be sure all hardware on this list and the above mentioned components is attached to
the furniture properly and kept tightened at all times.
PARTS LIST:
#
Description
Qty.
#
Description
Qty.
A
Table Top
1 pc
B
Pedestal
1 pc
C
Foot
4 pcs
D
Mounting Plate
1 pc
E
Leaf
1 pc
F
Leaf Bag
1 pc
G
Hardware Pack
1 bag
Assembly Procedure: (Please follow the sketches below.)
Step 1: Unpack, inspect, and read assembly instruction carefully. Lay out the parts and hardware.
Make sure the quantity of each is correct.
Step 2: Put the table top (A) face down on a soft and smooth surface to avoid damage or being
scratched. Remove the mounting plate (D) and keep the bolts, lock washers and flat
washers for step 5.
Step 3: Attach the feet (C) to the pedestal (B) with nuts (1), lock washers (3) and flat washers (2).
Tighten all the nuts (1) by wrench (4).
Step 4: Attach the mounting plate (D) to the post (B) with nuts (1), lock washers (3) and flat washers
(2). Tighten all the nuts (1) by wrench (4).
Note: There are two options to attach the pedestal to the mounting plate; either at a plus (+)
position or an (x) position.
Step 5: Attach the assembled pedestal to the table top (A) with the bolts, lock washers, flat washers
from step 2. Tighten all the bolts by wrench (4).
Step 6: Turn the table upright. Adjust the levelers under the feet (C) if necessary. Unlock the table
top (A), remove the leaf (E) and store it in leaf bag (F) as shown when leaf is not used. Then
lock the table top.
Note: If handled improperly, the act of installing and removing table leaf may damage the table.
Please use caution and delicate handling when installing and removing table leaf to prevent
damaging the table top surface and edges. It is best two persons are involved when installing or
removing table leaf.
Assembly is now complete.
INSTRUCTION SHEET
988/989-657
Single Pedestal Table

Step 2
4
A
D
Leveler
4
Hardware Pack (G)
Nut
15/16"
5/16"
Flat Washer
28 pcs
8 pcs
5/16"
Lock Washer
38 pcs
Wrench
41 pc
10~12mm
Leveler
E
ON OFF
ONOFF
1
4
3
2
F
1
432
Step 3
Step 4
Step 5
Step 6
D
A
D
B
C
C
C
B
C
C
C
B
CC
C
C
A