Universal Furniture URBAN SLEIGH HEADBOARD/FOOTBOARD 5/0 User manual

GOOD, AFFORDABLE, SMART DESIGN.
INSTRUCTION SHEET
356310 URBAN SLEIGH HEADBOARD/FOOTBOARD 5/0
35631R URBAN SLEIGH BEDRAIL 5/0
356320 URBAN SLEIGH HEADBOARD/FOOTBOARD 6/6
35633R URBAN SLEIGH BEDRAIL 6/6
356330 URBAN SLEIGH HEADBOARD/FOOTBOARD 6/0
35633R URBAN SLEIGH BEDRAIL 6/0
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small
parts that may have come loose inside the carton during shipment.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the
assistance of one or more persons in order to prevent personal injury and to insure parts are not damaged
during the assembly process. If dirty, clean finished parts with mild dishwashing liquid and water solution
applied on damp cloth. Cloth should not be excessively wet. Polish finish with soft cloth and an industry
recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residue and rough surfaces and also check for staples or nails left after removing the packaging material.
The manufacturer will not be held responsible if preventative steps are not taken prior to installation.
(3) Unpack and dispose of all packing material but be careful not to throw away any assembly parts or
hardware. Read the instruction sheet and parts list carefully. Remove all staples and screws used for
packaging carefully using pliers and or screwdrivers to prevent injury and scratching or damaging flooring.
(4) During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be
periodically inspected and re-tightened to prevent damage to the furniture and (or) personal property or cause
injury. Always check to be sure all hardware on this list and the above mentioned components is attached to
the furniture properly and kept tightened at all times.
PARTS LIST:
# Description Qty. # Description Qty.
A Footboard 1 pc E Metal Slat 3 pcs
B Headboard 1 pc F Side Rail 2 pcs
C Foot 4 pcs G Hardware Pack 1 bag
D Support Leg 6 pcs
Assembly Procedure: (Please follow the sketches below.)
Step 1: Unpack, inspect, and read assembly instruction carefully. Lay out the parts and hardware.
Make sure the quantity of each is correct.
Step 2: Attach the threaded rod ( 1 ) to the footboard ( A ) and then fix the foot ( C ) to the footboard
( A ) shown as the sketch. Please tighten the hardware for this step.
Step 3: Fix the foot ( C ) to the headboard ( B ) with the flat washer ( 3 ) and flat head bolt ( 2 ),
please tighten the bolts for this step.
Step 4: Fix the support leg ( D ) to the metal slat ( E ) with the flat head bolt ( 5 ), please tighten the
bolts for this step.And then attach the leveler ( 10 ) to the support leg ( D ).
Step 5:. Attach the side rail ( F ) to the footboard ( A ) with the flat head bolt ( 4 ) and headboard with
the flat head bolt ( 5 ) and the nut ( 6 ) shown as the sketch.
Step 6: Fix the metal slat ( E ) to the side rail ( F ) with the flat head bolt ( 5 ) and the nut ( 6 ) shown
as the sketch.
Please tighten all the bolts and adjust the leveler if needed. Assembly is now complete.

GOOD, AFFORDABLE, SMART DESIGN.
INSTRUCTION SHEET
A
1
FLAT HEAD BOLT
5/16"
C

GOOD, AFFORDABLE, SMART DESIGN.
INSTRUCTION SHEET
6
C
B
A
10

GOOD, AFFORDABLE, SMART DESIGN.
INSTRUCTION SHEET
6
DC