Universal Pumps UP-TECH40PC - 804908 User manual

Garden Jet Pump
Instruction Manual
Model: UP-TECH40PC - 804908

Incorrect pump type. Select suitable model.
Insufficient
pressure
The inlet pipeline is too long
or with too many bends, or/and
pipe diameter is not selected
as required.
Apply the pipe with the
stipulated diameter, and make
the inlet pipe short.
Inlet pipeline, filter screen or
pump chamber is blocked by
foreign materials.
Clean pipeline, foot valve or
pump chamber, clear foreign
materials.
Symptom Cause Corrective Action
Motor works
intermittently
or the stator
winding is
burned out
The impeller is jammed or
overload operation for a long
time.
in Clear in the
pump chamber; operate the
pump under the rated flow.
foreign materials
Incorrect grounding, broken
cable or the electric pump is
struck by lightning.
Properly grounded, replace the
broken cable , and replace
winding coils.
CONTENTS
1. Applications
2. Model Description
3. Technical Data
4. Implementation Standards
5. Safety Precautions
6. Product Structure
7. Pipeline Installation
8. Start-up and Maintenance
9. Troubleshooting
.......................................
..............................
...................................
...................
.............................
...............................
............................
....................
.................................
2
2
3
3
3
5
5
7
8

1
Incorrect pump type. Select suitable model.
Insufficient
pressure
The inlet pipeline is too long
or with too many bends, or/and
pipe diameter is not selected
as required.
Apply the pipe with the
stipulated diameter, and make
the inlet pipe short.
Inlet pipeline, filter screen or
pump chamber is blocked by
foreign materials.
Clean pipeline, foot valve or
pump chamber, clear foreign
materials.
Symptom Cause Corrective Action
Motor works
intermittently
or the stator
winding is
burned out
The impeller is jammed or
overload operation for a long
time.
in Clear in the
pump chamber; operate the
pump under the rated flow.
foreign materials
Incorrect grounding, broken
cable or the electric pump is
struck by lightning.
Properly grounded, replace the
broken cable , and replace
winding coils.
CONTENTS
1. Applications
2. Model Description
3. Technical Data
4. Implementation Standards
5. Safety Precautions
6. Product Structure
7. Pipeline Installation
8. Start-up and Maintenance
9. Troubleshooting
.......................................
..............................
...................................
...................
.............................
...............................
............................
....................
.................................
2
2
3
3
3
5
5
7
8

2
8 1
Check the pump after power cut-off.
9. Troubleshooting
The motor
can not be
started
The motor is
in operation,
but no water
is discharged
Single-phase power supply
(three-phase electric motor):
a. poor connection of the power
switch;
b. fuse is burned out;
c. loose power lead;
d. phase failure of the cable
Capacitor is burned out.
The rotating shaft and bearing
are jammed.
Impeller is jammed.
Stator winding is damaged.
Incorrect direction of pump
rotation.
The pump is not fully filled with
water.
a. repair switch contact or
replace the switch;
b. replace the safety fuse;
c. check and tighten the power
connector;
d. repair or replace cables.
Replace with a same type
capacitor (send to the
maintenance point for repair).
Replace the bearing (send to
the maintenance point for repair).
Turn rotating shaft of the fan
blade terminal with screw driver
to let it rotate flexibly or demount
the pump body to clear sundries.
Replace winding coils (send to
the maintenance point for repair).
Invert two-phase wirings of the
motor (three-phase motor).
Symptom Cause Corrective Action
Re-fill the pump with water.
The impeller is damaged. Replace the impeller (send to
the maintenance point for repair).
Leakage of the suction pipe. Check sealing of various joints
of the inlet pipelines.
Water level is too low.
Adjust installation height of the pump.
Freeze caused by accumulated
water in the pipeline or the
chamber.
Water that is too hot can result
in the failure of plastic parts.
Start up the pump after ice is
melted.
Replace the damaged parts
(send to the maintenance point
for repair)
Meaning of crossed –out wheeled dustbin:
Do not dispose of electrical appliances as
unsorted municipal waste, use separate
collection facilities.
Contact you local government for information
regarding the collection systems available.
This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have
been given supervision or instruction concerning
use of the appliance in a safe way and
understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be
made by children without supervision.
If the appliance or the supply cord is damaged, it
must be repaired by manufacturer, its service
agent or qualified person.
Attention!

3
8. Start-up and Maintenance
2 7
Note:
1.)If no water can be pumped in 5 minutes after the pump is filled with water
and started up, turn off and refill the pump, or check the leakage of inlet
pipelines, then restart the pump.
For frost and freeze protection, remove the discharge plug on the air tank
and drain the water in the pump chamber completely. Before restart the
pump, it’s necessary to remove the filling plug, fill the pump fully with water,
and then screw the filling plug.
In case of no use for a long time, discharge the water in the pump chamber
and store the pump in a dry, well-ventilated place.
If the ambient temperature is high, make sure the pump works in a well-
ventilated place to avoid electrical faults caused by dew on electrical parts.
In case of overheat or abnormal operation of the pump motor, cut off the
power supply immediately, and check the faults according to the following
form.
2).
3).
4).
5).
Do not switch on the pump if the pump chamber is not fully
filled with water.
Do not touch the electric pump unless the power of pump is
cut off for over 5 minutes.
Do not remove the pump bonnet unless the water in pump
chamber is completely drained.
Stir the fan with a screwdriver to
check if the pump rotates flexibly
before startup. Remove the filling
plug and prime the pump
chamber fully with clean water,
then screw the filling plug. Keep
the valve wide opened during
startup. When the pump runs
normally, adjust the valve to the
required flow (The range of flow
and head is shown on the
nameplate).
1. Applications
It is applicable to household water supply, equipment support, well water
lifting, pipeline pressurization, garden watering, vegetable greenhouse
watering, fish farming and poultry raising, etc..
Transfer clean water and other non-corrosive liquids with low viscosity; do
not transport inflammable, explosive, gasified liquids and liquids containing
solid particles or fibers. The liquid PH value shall be between 6.5 and 8.5.
The pump can work automatically, equipped with pressure tank, pressure
switch and other necessary parts. Function features of the automatic pump
are as follows: when the power is on, turn on the water tap and the pump
will start working automatically; when the water tap is turned off, the pump
will stop working automatically. If a water tower is used along with the
automatic pump, connect to the upper limit switch and the pump will start or
stop working automatically with water level in the water tower.
Remark:
Read the instructions carefully and follow the rules for safe
operation.
The operator shall take full responsibility for personal injury,
pump damage and other property losses caused by violation
of safety cautions.

4
A:
1. Drain Plug
2. Electric pump
3. Water tap
4. Outlet pipe
Incorrect Installation Diagram
Correct Installation Diagram A
B
B2B1
5. Filling plug
6. Tie-in
7. Inlet pipe
8. Foot valve
36
Do not use soft rubber tube for inlet
pipeline during pump installation.
The bottom valve shall be vertically
installed with a distance of 30 cm
from the water bottom to avoid
suction of sediment (A2).
All connections of the inlet pipeline
must be sealed. To ensure water
suction, it’s necessary to reduce the
quantity of bents of the pipeline.
The diameter of inlet pipeline must
not be less than that of the pump
inlet to avoid big hydraulic loss and
small water flow.
Pay attention to the water level
during operation. The bottom valve
shall not be above the water surface
(A1);
In case the inlet pipeline is more
than 10 m in length or over 4 m in
hoisting height, the diameter of the
inlet pipeline must be bigger than
that of the pump inlet.
Make sure that the pump is not
affected by the pipeline pressure
during pipeline installation.
It is recommended to install a filter
on inlet pipeline to avoid incoming of
solid particles to the electric pump.
Before first operation, the inlet
pipeline must be fully filled with
water and installed with a bottom
valve.
1.)
2).
3).
4).
5).
6).
7).
8).
Note for outlet pipeline installation:
The diameter of the outlet pipeline shall
be not less than that of the pump outlet
to reduce the pressure drop, high flow
rate and noise to the lowest level.
Notes for inlet pipeline installation:
9).
12
3
4
5
6
7
8
Max:8m
3. Technical Data
Max. flow: 53 L/min
Max. head: 30 m
Output power: 0.3 ~ 0.4 kW
Max. suction: 8 m
Protection class: IPX4
Insulation class: F
Max. ambient temperature: +40℃
4. Implementation Standards
IEC/EN 60335-1 Household and similar electrical appliances--safety
Part1: General requirements.
IEC/EN 60335-2-41 Household and similar electrical appliances--safety
Part2-41:Particular requirements for pump.
2006/95/EC Low voltage directive
5. Safety Precautions
Manual
ON OFF
OO
DANGEROUS
1. To ensure normal and safety operation of the electric
pump, read the manual carefully before use.
2. To avoid electric shock, make sure the pump is safely
grounded and equipped with an earth leakage circuit
breaker. Do not get the plug wet and do not use any
socket in an area with high humidity.
3. Do not touch the electric pump while working; do not
wash, swim near working area or let livestock into the
water to avoid accidents.

5
45
1234567
8
9
10 11 12
13
14 15 16
POS.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Part
Plug
Pump body
Diffuser
O-ring
Impeller
Mechanical seal
Bracket cover
Support
Handle
Rotor
Stator
Terminal box
Switch cover
Rear cover
Fan
Motor cover
7. Pipeline Installation
This product shall be installed and maintained by a qualified
person who is proficient with this instruction.
The installation and operation must be in accordance with local
regulations and the recognized operation criteria.
Install the pipeline properly according to the requirement of this
instruction, and protect it from freezing.
1. Make the inlet pipeline as
short as possible and keep
bends as few as possible
during installation. Keep the
pump in a dry and well-
ventilated place. In condition of
outdoor installation outdoor,
make sure the pump is
properly protected by weather-
proof covering.
2. Installation of valves on inlet
and outlet pipelines is
necessary. The valve installed
on inlet pipeline shall be one-
way valve.
Max. Water Temperature :40℃
Min. Water Temperature : 4℃
6. Product Structure
4℃
4. Avoid splashing pressured water to the electric pump
Do not immerse the pump in water.
5. Keep the pump in a well-ventilated place.
6. If the environment temperature is below 4 or after
long period of non-use, the liquid inside shall be
discharged for freeze and frost protection.
℃
7. The pumped liquid may be hot and under high
pressure, before moving and disassembling the pump.
valves in both sides of the pump should be turned off
first and then empty liquids in the pump and pipelines so
as not to be scalded.
8. Never use the pump to transport inflammable, gasifying
or explosive liquid that exceeds the specified liquids in this
manual.
9. The power supply should be in accordance with the
voltage stated in the nameplate. If the pump is not be
used for a long time, empty it completely, wash it with
clean water and store it in a dry, well-aired place.
Max.35℃
220-240V~50Hz 600W
Hmax:35m Hmin:2m
Qmax:60 l/min IPX4
UP-TECH40
OFF
O
OFF
O
CHEMICALS

6
45
1234567
8
9
10 11 12
13
14 15 16
POS.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Part
Plug
Pump body
Diffuser
O-ring
Impeller
Mechanical seal
Bracket cover
Support
Handle
Rotor
Stator
Terminal box
Switch cover
Rear cover
Fan
Motor cover
7. Pipeline Installation
This product shall be installed and maintained by a qualified
person who is proficient with this instruction.
The installation and operation must be in accordance with local
regulations and the recognized operation criteria.
Install the pipeline properly according to the requirement of this
instruction, and protect it from freezing.
1. Make the inlet pipeline as
short as possible and keep
bends as few as possible
during installation. Keep the
pump in a dry and well-
ventilated place. In condition of
outdoor installation outdoor,
make sure the pump is
properly protected by weather-
proof covering.
2. Installation of valves on inlet
and outlet pipelines is
necessary. The valve installed
on inlet pipeline shall be one-
way valve.
Max. Water Temperature :40℃
Min. Water Temperature : 4℃
6. Product Structure
4℃
4. Avoid splashing pressured water to the electric pump
Do not immerse the pump in water.
5. Keep the pump in a well-ventilated place.
6. If the environment temperature is below 4 or after
long period of non-use, the liquid inside shall be
discharged for freeze and frost protection.
℃
7. The pumped liquid may be hot and under high
pressure, before moving and disassembling the pump.
valves in both sides of the pump should be turned off
first and then empty liquids in the pump and pipelines so
as not to be scalded.
8. Never use the pump to transport inflammable, gasifying
or explosive liquid that exceeds the specified liquids in this
manual.
9. The power supply should be in accordance with the
voltage stated in the nameplate. If the pump is not be
used for a long time, empty it completely, wash it with
clean water and store it in a dry, well-aired place.
Max.35℃
220-240V~50Hz 600W
Hmax:35m Hmin:2m
Qmax:60 l/min IPX4
XKJ-600P
Schutzklasse:IIsolationsklasse:F
OFF
O
OFF
O
CHEMICALS

7
45
1234567
8
9
10 11 12
13
14 15 16
POS.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Part
Plug
Pump body
Diffuser
O-ring
Impeller
Mechanical seal
Bracket cover
Support
Handle
Rotor
Stator
Terminal box
Switch cover
Rear cover
Fan
Motor cover
7. Pipeline Installation
This product shall be installed and maintained by a qualified
person who is proficient with this instruction.
The installation and operation must be in accordance with local
regulations and the recognized operation criteria.
Install the pipeline properly according to the requirement of this
instruction, and protect it from freezing.
1. Make the inlet pipeline as
short as possible and keep
bends as few as possible
during installation. Keep the
pump in a dry and well-
ventilated place. In condition of
outdoor installation outdoor,
make sure the pump is
properly protected by weather-
proof covering.
2. Installation of valves on inlet
and outlet pipelines is
necessary. The valve installed
on inlet pipeline shall be one-
way valve.
Max. Water Temperature :40℃
Min. Water Temperature : 4℃
6. Product Structure
4℃
4. Avoid splashing pressured water to the electric pump
Do not immerse the pump in water.
5. Keep the pump in a well-ventilated place.
6. If the environment temperature is below 4 or after
long period of non-use, the liquid inside shall be
discharged for freeze and frost protection.
℃
7. The pumped liquid may be hot and under high
pressure, before moving and disassembling the pump.
valves in both sides of the pump should be turned off
first and then empty liquids in the pump and pipelines so
as not to be scalded.
8. Never use the pump to transport inflammable, gasifying
or explosive liquid that exceeds the specified liquids in this
manual.
9. The power supply should be in accordance with the
voltage stated in the nameplate. If the pump is not be
used for a long time, empty it completely, wash it with
clean water and store it in a dry, well-aired place.
Max.35℃
220-240V~50Hz 600W
Hmax:35m Hmin:2m
Qmax:60 l/min IPX4
XKJ-600P
Schutzklasse:IIsolationsklasse:F
OFF
O
OFF
O
CHEMICALS
[This page has been left blank intentionally]

8
8. Start-up and Maintenance
2 7
Note:
1.)If no water can be pumped in 5 minutes after the pump is filled with water
and started up, turn off and refill the pump, or check the leakage of inlet
pipelines, then restart the pump.
For frost and freeze protection, remove the discharge plug on the air tank
and drain the water in the pump chamber completely. Before restart the
pump, it’s necessary to remove the filling plug, fill the pump fully with water,
and then screw the filling plug.
In case of no use for a long time, discharge the water in the pump chamber
and store the pump in a dry, well-ventilated place.
If the ambient temperature is high, make sure the pump works in a well-
ventilated place to avoid electrical faults caused by dew on electrical parts.
In case of overheat or abnormal operation of the pump motor, cut off the
power supply immediately, and check the faults according to the following
form.
2).
3).
4).
5).
Do not switch on the pump if the pump chamber is not fully
filled with water.
Do not touch the electric pump unless the power of pump is
cut off for over 5 minutes.
Do not remove the pump bonnet unless the water in pump
chamber is completely drained.
Stir the fan with a screwdriver to
check if the pump rotates flexibly
before startup. Remove the filling
plug and prime the pump
chamber fully with clean water,
then screw the filling plug. Keep
the valve wide opened during
startup. When the pump runs
normally, adjust the valve to the
required flow (The range of flow
and head is shown on the
nameplate).
1. Applications
It is applicable to household water supply, equipment support, well water
lifting, pipeline pressurization, garden watering, vegetable greenhouse
watering, fish farming and poultry raising, etc..
Transfer clean water and other non-corrosive liquids with low viscosity; do
not transport inflammable, explosive, gasified liquids and liquids containing
solid particles or fibers. The liquid PH value shall be between 6.5 and 8.5.
The pump can work automatically, equipped with pressure tank, pressure
switch and other necessary parts. Function features of the automatic pump
are as follows: when the power is on, turn on the water tap and the pump
will start working automatically; when the water tap is turned off, the pump
will stop working automatically. If a water tower is used along with the
automatic pump, connect to the upper limit switch and the pump will start or
stop working automatically with water level in the water tower.
Remark:
Read the instructions carefully and follow the rules for safe
operation.
The operator shall take full responsibility for personal injury,
pump damage and other property losses caused by violation
of safety cautions.
2. Model Description
XKJ x x
Pump body material: I (Cast Iron),
P (Plastic) or S (Stainless Steel)
Rated power (W)
Garden Jet Pump
A:
1. Drain Plug
2. Electric pump
3. Water tap
4. Outlet pipe
Incorrect Installation Diagram
Correct Installation Diagram A
B
B2B1
5. Filling plug
6. Tie-in
7. Inlet pipe
8. Foot valve
36
Do not use soft rubber tube for inlet
pipeline during pump installation.
The bottom valve shall be vertically
installed with a distance of 30 cm
from the water bottom to avoid
suction of sediment (A2).
All connections of the inlet pipeline
must be sealed. To ensure water
suction, it’s necessary to reduce the
quantity of bents of the pipeline.
The diameter of inlet pipeline must
not be less than that of the pump
inlet to avoid big hydraulic loss and
small water flow.
Pay attention to the water level
during operation. The bottom valve
shall not be above the water surface
(A1);
In case the inlet pipeline is more
than 10 m in length or over 4 m in
hoisting height, the diameter of the
inlet pipeline must be bigger than
that of the pump inlet.
Make sure that the pump is not
affected by the pipeline pressure
during pipeline installation.
It is recommended to install a filter
on inlet pipeline to avoid incoming of
solid particles to the electric pump.
Before first operation, the inlet
pipeline must be fully filled with
water and installed with a bottom
valve.
1.)
2).
3).
4).
5).
6).
7).
8).
Note for outlet pipeline installation:
The diameter of the outlet pipeline shall
be not less than that of the pump outlet
to reduce the pressure drop, high flow
rate and noise to the lowest level.
Notes for inlet pipeline installation:
9).
12
3
4
5
6
7
8
Max:8m
3. Technical Data
Max. flow: 53 L/min
Max. head: 30 m
Output power: 0.3 ~ 0.4 kW
Max. suction: 8 m
Protection class: IPX4
Insulation class: F
Max. ambient temperature: +40℃
4. Implementation Standards
IEC/EN 60335-1 Household and similar electrical appliances--safety
Part1: General requirements.
IEC/EN 60335-2-41 Household and similar electrical appliances--safety
Part2-41:Particular requirements for pump.
2006/95/EC Low voltage directive
5. Safety Precautions
Manual
ON OFF
OO
DANGEROUS
1. To ensure normal and safety operation of the electric
pump, read the manual carefully before use.
2. To avoid electric shock, make sure the pump is safely
grounded and equipped with an earth leakage circuit
breaker. Do not get the plug wet and do not use any
socket in an area with high humidity.
3. Do not touch the electric pump while working; do not
wash, swim near working area or let livestock into the
water to avoid accidents.

9
A:
1. Drain Plug
2. Electric pump
3. Water tap
4. Outlet pipe
Incorrect Installation Diagram
Correct Installation Diagram A
B
B2B1
5. Filling plug
6. Tie-in
7. Inlet pipe
8. Foot valve
36
Do not use soft rubber tube for inlet
pipeline during pump installation.
The bottom valve shall be vertically
installed with a distance of 30 cm
from the water bottom to avoid
suction of sediment (A2).
All connections of the inlet pipeline
must be sealed. To ensure water
suction, it’s necessary to reduce the
quantity of bents of the pipeline.
The diameter of inlet pipeline must
not be less than that of the pump
inlet to avoid big hydraulic loss and
small water flow.
Pay attention to the water level
during operation. The bottom valve
shall not be above the water surface
(A1);
In case the inlet pipeline is more
than 10 m in length or over 4 m in
hoisting height, the diameter of the
inlet pipeline must be bigger than
that of the pump inlet.
Make sure that the pump is not
affected by the pipeline pressure
during pipeline installation.
It is recommended to install a filter
on inlet pipeline to avoid incoming of
solid particles to the electric pump.
Before first operation, the inlet
pipeline must be fully filled with
water and installed with a bottom
valve.
1.)
2).
3).
4).
5).
6).
7).
8).
Note for outlet pipeline installation:
The diameter of the outlet pipeline shall
be not less than that of the pump outlet
to reduce the pressure drop, high flow
rate and noise to the lowest level.
Notes for inlet pipeline installation:
9).
12
3
4
5
6
7
8
Max:8m
3. Technical Data
Max. flow: 53 L/min
Max. head: 30 m
Output power: 0.3 ~ 0.4 kW
Max. suction: 8 m
Protection class: IPX4
Insulation class: F
Max. ambient temperature: +40℃
4. Implementation Standards
IEC/EN 60335-1 Household and similar electrical appliances--safety
Part1: General requirements.
IEC/EN 60335-2-41 Household and similar electrical appliances--safety
Part2-41:Particular requirements for pump.
2006/95/EC Low voltage directive
5. Safety Precautions
Manual
ON OFF
OO
DANGEROUS
1. To ensure normal and safety operation of the electric
pump, read the manual carefully before use.
2. To avoid electric shock, make sure the pump is safely
grounded and equipped with an earth leakage circuit
breaker. Do not get the plug wet and do not use any
socket in an area with high humidity.
3. Do not touch the electric pump while working; do not
wash, swim near working area or let livestock into the
water to avoid accidents.

10
8 1
Check the pump after power cut-off.
9. Troubleshooting
The motor
can not be
started
The motor is
in operation,
but no water
is discharged
Single-phase power supply
(three-phase electric motor):
a. poor connection of the power
switch;
b. fuse is burned out;
c. loose power lead;
d. phase failure of the cable
Capacitor is burned out.
The rotating shaft and bearing
are jammed.
Impeller is jammed.
Stator winding is damaged.
Incorrect direction of pump
rotation.
The pump is not fully filled with
water.
a. repair switch contact or
replace the switch;
b. replace the safety fuse;
c. check and tighten the power
connector;
d. repair or replace cables.
Replace with a same type
capacitor (send to the
maintenance point for repair).
Replace the bearing (send to
the maintenance point for repair).
Turn rotating shaft of the fan
blade terminal with screw driver
to let it rotate flexibly or demount
the pump body to clear sundries.
Replace winding coils (send to
the maintenance point for repair).
Invert two-phase wirings of the
motor (three-phase motor).
Symptom Cause Corrective Action
Re-fill the pump with water.
The impeller is damaged. Replace the impeller (send to
the maintenance point for repair).
Leakage of the suction pipe. Check sealing of various joints
of the inlet pipelines.
Water level is too low.
Adjust installation height of the pump.
Freeze caused by accumulated
water in the pipeline or the
chamber.
Water that is too hot can result
in the failure of plastic parts.
Start up the pump after ice is
melted.
Replace the damaged parts
(send to the maintenance point
for repair)
Meaning of crossed –out wheeled dustbin:
Do not dispose of electrical appliances as
unsorted municipal waste, use separate
collection facilities.
Contact you local government for information
regarding the collection systems available.
This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have
been given supervision or instruction concerning
use of the appliance in a safe way and
understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be
made by children without supervision.
If the appliance or the supply cord is damaged, it
must be repaired by manufacturer, its service
agent or qualified person.
Attention!

11
Notes

12
P_P_UNIVERSAL_MANUAL_804911
™
WHITE INTERNATIONAL PTY LTD
60 Ashford Ave Milperra NSW 2214
PO Box 304 Milperra LPO NSW 2214
Customer Service Hotline [phone]
Fax [phone]
Email Sales: [email protected]
www.whiteint.com.au
WHITE INTERNATIONAL NZ LTD
15G Kerwyn Avenue
East Tamaki, Auckland 2013, New Zealand
Customer Service Hotline [phone]
Customer Service Faxline 0800 804 344
Email Sales: [email protected].nz
www.whiteint.co.nz
White International Pty Ltd
Limited Product Warranties
TERMS & CONDITIONS
This warranty is given in addition to the consumer guarantees found within the Australian Competition and Consumer Act 2010 (Cth)
for goods purchased in Australia and the Consumer Guarantees Act 1993 NZ for goods purchased in New Zealand:
1) White International Pty Ltd / White International NZ Ltd (White International) warrant that all products distributed are free from
defects in workmanship and materials, for their provided warranty period as indicated on the top or opposite side of this document.
Subject to the conditions of the warranty, White International will repair any defective products free of charge at the premises of our
authorised service agents throughout Australia and New Zealand if a defect in the product appears during the warranty period. If you
believe that you have purchased a defective product and wish to make a claim under this warranty, contact us on our Sales Hotline on
1300 783 601, or send your claim to our postal address or fax line below and we will advise you as to how next to proceed. You will be
required to supply a copy of your proof of purchase to make a claim under this warranty.
2) This warranty excludes transportation costs to and from White International or its appointed service agents and excludes defects due
to non-compliance with installation instructions, neglect or misuse, inadequate protection against the elements, low voltage or use or
operation for purposes other than those for which they were designed. For further information regarding the suitability of your intended
application contact us on our Sales Hotline on 1300 783 601. If you make an invalid claim under this warranty, the original product will
be sent back to you unrepaired.
3) This warranty refers only to products sold after the 1st January 2012, and is not transferable to another product type and only applies
to the original owner, purchaser or end user, and is in addition to the consumer guarantees found within the Competition and Consumer
Act 2010 (Cth) for goods purchased in Australia and the Consumer Guarantees Act 1993 (NZ) for goods purchased in New Zealand.
4) Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or
refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the
goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
5) To the fullest extent permitted by law, White International excludes its liability for all other conditions or warranties which would or
might otherwise be implied at law. To the fullest extent permitted by law, White International’s liability under this warranty and any other
conditions, guarantees or warranties at law that cannot be excluded, including those in the Competition and Consumer Act 2010 (Cth),
is expressly limited to:
(a) in the case of products, the replacement of the product or the supply of equivalent product, the payment of the cost of replacing the
product or of acquiring an equivalent product or the repair of the product or payment of the cost of having the product repaired, is at
the discretion of White
International or a 3rd party tribunal elected under the Competition and Consumer Act 2010 (Cth) for goods purchased in Australia and
the Consumer Guarantees Act 1993 (NZ) for goods purchased in New Zealand; and
6) To the fullest extent permitted by law, this warranty supersedes all other warranties attached to the product or its packaging.
7) In the case of services, supplying the services again or the payment of the cost of having the services supplied again, is at the
discretion of White International or a 3rd party tribunal elected under the Competition and Consumer At 2010 (Cth) for goods
purchased in Australia and the Consumer Guarantees Act 1993 (NZ) for goods purchased in New Zealand.
8) Our warranty commences from the date of purchase of the above mentioned pumps. Proof of purchase is required before
consideration under warranty is given. Record your date of purchase in the space below and retain this copy for your records.
Date of Purchase ..........................................................................
Model Purchased .........................................................................
12 MONTH WARRANTY
U
N
I
V
E
R
S
A
L
12
1
2
M
O
N
T
H
P
U
M
P
W
A
R
R
A
N
T
Y