Universal EXPLORE HOME TRANQUILITY U195320 User manual

INSTRUCTION
SHEET
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small
parts that may have come loose inside the carton during shipment.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the
assistance of one or more persons in order to prevent personal injury and to insure parts are not damaged
during the assembly process. If dirty, clean finished parts with mild dishwashing liquid and water solution
applied on damp cloth. Cloth should not be excessively wet. Polish finish with soft cloth and an industry
recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residue and rough surfaces and also check for staples or nails left after removing the packaging material.
The manufacturer will not be held responsible if preventative steps are not taken prior to installation.
(3) Unpack and dispose of all packing material but be careful not to throw away any assembly parts or
hardware. Read the instruction sheet and parts list carefully. Remove all staples and screws used for
packaging carefully using pliers and or screwdrivers to prevent injury and scratching or damaging flooring.
(4) During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be
periodically inspected and re-tightened to prevent damage to the furniture and (or) personal property or cause
injury. Always check to be sure all hardware on this list and the above mentioned components is attached to
the furniture properly and kept tightened at all times.
Metal Slat
Metal Rail
Slat Panel
8PCS
1PC
2PCS
1PC
4PCS
PART LIST
F
G
1PC
1PC
Center Support
A
Headboard
Side rail
Footboard
B
C
D
E
5/16"*23*2mm
7
Flat washer 12PCS
METAL FRAME HARDWARE PACK
5/16"
9
10
11
5/16"*2-3/4"
8
2PCS
5/16"*1
87*19mm
10PCS
2PCS
1PC
Nut
Bolt
Bolt
Wrench
1
Spring washer
Curved washer
Nut
2
3
4
5
6
Screw
Wrench
5/16" *3"
5/16"
27.5*8*15mm
13*13*5mm
8*1-1/4"mm
87*19mm
8PCS
8PCS
8PCS
8PCS
8PCS
1PC
HEAD BOARD＆FOOT BOARD HARDWARE PACK
Bolt
TRANQUILITY BED KINGU195320

INSTRUCTION
SHEET
Assembly Procedure: (Please follow the sketches below.)
Unpack, inspect, and read assembly instruction carefully. Lay out the parts and hardware. Make sure
the quantity of each is correct.
Step 1: Assemble side rails (C) with headboard (B) using bolts (1), curved washers (2), spring
washers (3) and nuts (4). Tighten them by wrench (6).
Step 2: Attach the metal rail (G) to the metal slat (F) with nuts (7), washers (8) and bolts (9) using
Wrench (11)
Step 3: Attach the metal slat (F) to side rail (C) with washer (8), Bolt (10) by Wrench (11).
Step 4: Assemble side rails (C) with footboard (D) using bolts (1), curved washers (2), spring
washers (3) and nuts (4). Tighten them by wrench (6).
Step 5:Attach the footboard (D) to the metal rail (G) with washer (8), Bolt (10)by Wrench (11).
Step 6: Screw center support ( A) to the slat panels (E)
Step 7: Put slat panels (E) onto the inside notches of side rails (C), tighten them with screws (5) by
Screwdriver (not provided).
Note: U195320 bed has 8pcs center support.
Assembly is now complete.
6
4
3
2
1
B
C
C
F
G
TRANQUILITY BED KINGU195320

INSTRUCTION
SHEET
C
B
C
STEP 3
F
G
C
B
C
STEP 4
STEP 5
D
6
TRANQUILITY BED KINGU195320

INSTRUCTION
SHEET
D
C
5
STEP 6
A
STEP 7
AAAA
A
A
A
A
E
E
E
E
C
B
U195320 TRANQUILITY BED KING