Univet EOS HP User manual

MANUFACTURER:
Univet s.r.l.
via Giovanni Prati, 87
25086 Rezzato (BS) Italy
www.univet-optic.com
We congratulate you on the purchase of a Univet illumination system - Made in Italy. To ensure safe use
please observe the following notes.
Symbols reported on the products and/or on the case:

High-power LED lighting system powered by rechargeable Li-ion batteries, with intensity adjuster and
Bluetooth remote control
Technical specifications:
- Power supply: 1 Li-ion rechargeable battery
- Autonomy at max power: >8 hours
- Recharge time: approx. 7.5 hours
- Colour temperature: 5,700K
- Max luminosity: 45000 lx
- Battery charger power supply unit: 100-230V~, 50-60 Hz
- Environmental conditions: USE Temperature +10 °C to +30 °C Relative humidity 30% to 75% TRANSPORT
AND STORAGE Temperature -10° to +50°Relative humidity 10% to 80%
- Conformity: CEE 93/42, EN60601-1 3rd edition, EN60601-1-2:2007,EN62471 1st edition, directive
2014/53/EU, EN62479:2010, EN301 489-1 v1.9.2, EN301 489-17 v2.2.1, EN300 328 v1.9.1, CFR title 47 part
15, CFR title 47 part 15.247, ICES-003 issue 5 2012, RSS-247.
WARNING
Attention, failure to follow these safety instructions could lead to fire, electric shock, injury or damage to
the LED lighting system or to other property. Carefully read the following warnings before using the LED
lighting system. Do not use the device if it has been damaged. Do not tamper with or disassemble any
component of the system. Do not open the controller and do not attempt any repair operation. Do not
attempt to replace the battery. Do not expose the lighting system to conditions that may ignite the battery.
Avoid contact with sources of heat or naked flames. Do not use in spaces with flammable anesthetic
mixtures.
When the LED lighting system is not used store it in its container. Do not immerse any component in liquid
substances. Prevent liquid substances from entering the slots or the connection port. Do not look directly at
the light emitted by the LED nor direct the light to the eyes of the patient. Never place magnifying glasses
or other optical systems in front of the light. Use exclusively the components provided: do not combine the
components of the system with other lighting systems or electronic equipment. Use only the charger power
unit supplied. Field of application: the device is intended for use during medical examinations and therapy.
For internal use only.
DESCRIPTION OF DEVICE
The LED system (Light Emitting Diode) Univet EOS HP is a portable lighting device that can be worn by the
operator to illuminate the visual field during the execution of work. Thanks to its structure, the LED EOS HP
can be easily hooked up to all models of magnifying devices manufactured by Univet, thus providing an
integrated vision system.
The Li-ion battery with high capacity supplied with the device allows full autonomy to the user, ensuring
constant illumination for at least 8 hours.
It is recommended to perform a full charge cycle before using the device.

FITTING THE LED ON THE MAGNIFICATION SYSTEM
The lighting device EOS can be conveniently mounted on any model of magnifying system Univet thanks to
the magnetic coupling provided. UNIVERSAL
CLIP Open the clip and apply it on the frame at the nasal bridge; the terminals of the clip must adhere to
both surfaces of the lenses. FLIP-UP UNIVET Use the support provided with the model by screwing the
same using the special screws to seal on the center pin placed between the monocles. EVO Use the support
provided with the model by following the installation instructions given in the leaflet of the magnifying
system.
BLUETOOTH REMOTE CONTROLLER
Each remote controller shall be paired with a single control unit and connected to it before the use.
PAIRING FUNCTION
The pairing function shall be performed only when a new control unit or Bluetooth remote controller is used.
Devices are already paired by Univet prior to shipment.

1. Ensure the control unit in not in charge mode by removing it from wireless charging pad
2. Push and keep pushed for 8 seconds the command button (8)
3. During pairing function the command indicator LED (9) blinks in a red color very fast. It starts slowly
blinking in a red color as soon as the RF remote controller is correctly paired with the control unit.
CONNECT FUNCTION
This function enables the comunication betweeen RF remote controller and LED control unit and shall be
performed after every control unit’s charge or when the RF remote controller exits from the covered area of
10 meters far from the control unit. The need of a new connection is showed by no light of the command
indicator LED (9).
1. Ensure the control unit in not in charge mode by removing it from wireless charging pad
2. Quickly push and release the command button (8)
3. Command indicator LED (9) quickly blinks during connection, and it slowly blinks in a red color to confirm
the Bluetooth remote controller is corretly connected to the control unit.
USE OF REMOTE CONTROL
1. Quickly push and release command button (8) to turn ON the device
2. Push for 1sec and release command button (8) to turn OFF the device
3. Quickly push and release command button (8) to adjust brightness intensity among minimum, medium
and maximum levels
BATTERY CHARGING
1. Connect the wireless charging pad to the charger by using the USB cable.
2. Insert the charger into a wall socket 220V~50 Hz / 110V~60 Hz.
3. Place the control unit with the front surface in contact with the wireless charging pad. Please verify the
control unit is placed in the middle of the wireless charging pad surface
4. A single sound confirms the control unit is properly placed on the wireless charging pad. If the sound is
not emitted, remove the control unit from wireless pad and try to place it in the proper position.
5. A serie of 4 sounds informs the control unit is not properly placed on the wireless charging pad or the
battery is already charged
6. The following colors of charge status indicator LED (6) will indicate the charge status: RED: Charge mode.
The battery is charging - GREEN: Charge completed. The battery is ready for use. 10min after the full charge
is reached, the GREEN light turns off.
USING THE DEVICE
1. Connect the cable of the headlamp to the control unit using the dedicated connector (5)
2. Turn on the device by pressing the power button (1). The multicolor LED bar (2) shows for two seconds
the brightness setting in use

3. The multicolor LED bar (2) indicates the charge status: when the residual battery charge drops below
10% the indicator LED will become orange, while when the residual charge drops below 5% the light will
start flashing
4. Adjust the luminous intensity by acting on the adjustment buttons (3) and (4) on top of the controller: a
short pression causes the passage through five discrete steps. By keeping pushed buttons (3) or (4) a fine
adjustment of light intensity is allowed: release the button as soon as the desired brightness is reached
5. The multicolor LED bar (2) present on the front part of the controller will indicate in green color the level
of luminous intensity set during brightness adjustment
6. To turn off the device push the button (1). This device records the last brightness setting and keeps it
stored for the following use
UV FILTER
The filter UV525 enables shielding the ultraviolet radiation emitted by the LED that could interfere with
some work processes. The support is mounted on the lighting head by a slight pressure until it remains in
position. The movement of the ring nut allows the filter to be removed from the light beam without having
to unclip the support from the lighting head.
Should the filter support be excessively slack after being mounted on the spotlight, operate the clamping
screw gently.
CLEANING INSTRUCTIONS
Disconnect the cable from the lighting head before cleaning. Do not proceed with the cleaning while the
controller is connected to the charger.
Use a microfibre cloth to clean the lenses. The control unit can be cleaned with a soft cloth soaked in a
gentle disinfectant solution. Do not soak or spray any component with disinfectants and other liquids. The
LED lighting system cannot be sterilised in an autoclave. Make sure that the lighting system is completely
dry before use.
RADIO FREQUENCY DEVICE CERTIFICATION
FCC - FEDERAL COMMUNICATIONS COMMISSION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
WARNING: Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

ISED - INNOVATION, SCIENCE AND ECONOMIC DEVELOPMENT CANADA
This device complies with Industry Canada’s licence -exempt RSSs.
Operation is subject to the following two conditions:
(1) This device may not cause interference;
(2) This device must accept any interference, including interference that may cause undesired operation of
the device
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage;
(2) L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement